KitLog pro

Powered By Kitlog Pro v2.0

Terrences Web Site
Work Logs Found: 231
Category Work Time: 739 Hours
 Date
Hours
Work Log Summary

Details

 03-01-2019
4.00
Drill 1/4" and 5/16" holes in doublers/angles
Details
       

 02-25-2019
4.00
Drill Seat Front Angle and Rear Bottom Angle to ce
Details
     

 02-22-2019
6.00
Drill front section of Center Spar for 3/16" Rivet
Details
       

 02-18-2019
3.00
Disassemble center spar for upgrade--rear
Details

 02-17-2019
3.00
Disassemble center spar for upgrade--rear
Details
       

 02-11-2019
6.00
Disassemble center spar for upgrade
Details
       

 03-29-2017
5.00
Rivets Spar Caps and Doubler to Spar
Details
       

 03-23-2017
6.00
Rivet doubler to web, shims, and front rib attach
Details
       

 03-16-2017
2.00
Fill misdrilled 3/32" holes in web and doubler wit
Details

 03-10-2017
3.00
Disassemble, deburr, scour, clean, and prime left
Details
     

 03-06-2017
8.00
Drill holes for new left spar nose rib attachments
Details
       

 02-16-2015
3.00
Drill holes to attach left spar NR#1 to rib angles
Details
     

 02-15-2015
4.00
Drill nose rib anges for left spar NR#2, and NR#1
Details
       

 02-12-2015
4.00
Drill new angles for NR#2
Details
       

 02-10-2015
6.00
Left spar prep for nose ribs
Details
       

 12-08-2012
8.00
Project Restart: Logging work done in 2012
Details
       

 12-06-2012
3.00
Practice oval cut in .040 & remove rivets
Details
     

 12-05-2012
3.00
Riveted the doubler to the right wing spar
Details
       

 12-01-2012
2.00
Prime Right Spar Doubler Parts
Details

 11-30-2012
4.00
Prepare doubler for right wing spar
Details
       

 02-24-2012
3.00
Blend out damage to L-bottom spar cap
Details
       

 05-29-2011
4.00
Reassemble left aileron w/ balance & hinge
Details
       

 05-28-2011
8.00
Continued.: balance arm & piano hinge
Details
     

 05-26-2011
8.00
Install balance arm & piano hinge on right aileron
Details
       

 02-17-2011
2.00
Reinstall aileron trim servo
Details
       

 02-11-2011
4.00
Deburr, scour, clean, and prime new aileron joints
Details
     

 01-26-2011
6.00
Install R aileron counter-balance arm & ribs
Details
       

 01-22-2011
6.00
R aileron piano hinge conversion
Details
       

 01-16-2011
1.00
Revised mod process for right aileron
Details

 01-15-2011
2.00
Drill piano hinge attach holes to #30
Details
     

 01-14-2011
6.00
Drill inboard rib for left aileron counterbalance
Details
       

 01-05-2011
1.00
Drill inboard rib for left aileron counterbalance
Details
     

 11-13-2010
1.00
Drill out gussets for L-aileron
Details

 11-10-2010
5.00
Pilot drill L-aileron to hinge
Details
       

 11-07-2010
5.00
Prepare & pilot drill L Aileron for piano hinge
Details
       

 11-04-2010
2.00
Add L-angle back doubler behind aileron horn
Details
     

 11-03-2010
5.00
Mod left aileron to accept counter balance
Details
       

 10-25-2010
2.00
Disassemble left aileron to install balance, Hinge
Details
       

 10-21-2010
5.00
Drill & ream holes for left spar root doubler plat
Details
       

 08-13-2010
2.00
Remove web doubler from right spar
Details
       

 08-07-2010
2.00
Left spar cap rivet removal: bottom root
Details

 08-06-2010
3.00
Rivet the left top spar cap back together
Details
       

 08-06-2010
1.00
Confer with Zenair Re bend in R Spar at doubler
Details
       

 08-02-2010
3.00
Drill extra hole for AN3 bolt in extrusion & prime
Details
     

 07-29-2010
2.00
Back drill rivet holes through the spar cap extrus
Details

 07-23-2010
0.10
Remove rivets--continuation
Details

 07-23-2010
5.00
Remove rivets from left spar cap
Details
       

 07-21-2010
4.00
Drill wing attach 5/16 bolt holes to fit NAS bolts
Details
       

 07-09-2010
3.00
Drill the holes in the wing root doubler to final
Details
       

 07-03-2010
1.00
Replace one rivet
Details
       

 07-02-2010
3.00
Rivet spar web doubler in place
Details
       

 07-01-2010
2.00
Drill doubler and spar web, prepare for riveting
Details
     

 06-27-2010
5.00
De-rivet spar caps inboard & install web doubler
Details
       

 05-28-2010
2.00
Transfer punch & pilot drill holes in spar root do
Details
       

 05-27-2010
3.00
Rivet & bolt extrusion to right wing spar cap
Details
       

 05-26-2010
1.00
Set up work bench to rivet extruded angle to spar
Details
       

 05-24-2010
2.00
Deburr, scour, clean, and prime top spar cap joint
Details

 05-21-2010
0.01
Practice 3/16" Solid Riveting (cont.)
Details
       

 05-21-2010
2.00
Practice 3/16" Solid Riveting
Details
       

 05-04-2010
3.00
Remove bottom spar cap rivets & nose rib angles
Details
     

 03-24-2010
3.00
Drill spar cap extruded angle for rivets
Details

 03-23-2010
1.00
Position extruded angle for drilling
Details
     

 03-23-2010
3.00
Cut off spar cap angle and clean up spar cap
Details
       

 03-20-2010
1.00
Remove solid rivets from spar 2/2
Details

 03-20-2010
7.00
Remove solid rivets from spar 1/2
Details
       

 03-19-2010
2.00
Drill solid rivet heads on R wing spar
Details
     

 03-18-2010
8.00
Build jig to support main spar for riveting
Details
       

 03-13-2010
4.00
Remove the rivets in the wing skeleton
Details
       

 03-12-2010
4.00
Practice 5/32 solid riveting
Details

 03-09-2010
1.00
Solid Rivet Practice 2/2
Details
       

 03-09-2010
5.00
Solid Rivet Practice 1/2
Details
       

 03-04-2010
1.00
Bend L-angles & Z-angles 4/4
Details

 03-04-2010
1.00
Bend L-angles & Z-angles 3/4
Details

 03-04-2010
1.00
Bend L-angles & Z-angles 2/4
Details
       

 03-04-2010
8.00
Bend L-angles & Z-angles 1/4
Details
       

 02-16-2010
2.00
Rivet practice
Details
       

 02-15-2010
20.00
Practice Solid Riveting
Details
       

 01-15-2010
24.00
Add automatic electric outlet to compressor
Details
       

 11-25-2009
3.00
Remove clecoed skins, clear off work table
Details
       

 07-26-2009
3.00
Form sample of Z-angle
Details
       

 10-21-2008
1.00
Make up 3 rivet test specimens
Details

 06-29-2008
1.00
Check diameter of main spar bolt holes
Details
       

 06-13-2008
6.00
Make up 22 rivet strength test specimens
Details
       

 04-06-2008
1.00
Drill new holes for NR#4
Details
     

 04-04-2008
3.00
Add shims to move NR#7
Details
       

 04-03-2008
1.00
Positioned nose skin--problems with prepunched hol
Details
       

 04-02-2008
2.00
Drill holes for gas line, position nose skin
Details
     

 04-01-2008
2.00
Drill main spar pilot holes, etc.
Details
       

 03-30-2008
5.00
Drill remaining 3/32" holes in bottom skin
Details
       

 03-29-2008
4.00
Drill & cleco bottom rear skin
Details
     

 03-27-2008
2.00
Check wing twist, start drilling bottom skin
Details
       

 03-26-2008
0.00
Continue 3/26 entry: Kitlog Pro BUG
Details

 03-26-2008
2.00
Adjust positon of bottom rear skin
Details
       

 03-25-2008
2.00
Fuel system & bottom rear skin
Details
       

 03-24-2008
3.00
Redesign and build doublers to reinforce tie down
Details
       

 03-23-2008
2.00
Design doublers for tie down ring
Details
     

 03-20-2008
3.00
Rivet gascolator channel, etc.
Details
       

 03-19-2008
0.00
Continue gascolator channel
Details
       

 03-19-2008
4.00
Begin build of gascolator mount channel
Details
       

 03-18-2008
2.00
Put lightening holes in landing light channels
Details
       

 03-16-2008
1.00
Repair HF Rivet gun
Details

 03-15-2008
1.50
Mark rib stations on spars
Details

 03-13-2008
2.00
Drill out rib 9; drill replacement0
Details

 03-12-2008
2.00
Turn wing upside down and level
Details
       

 03-12-2008
0.50
Bottom rear skin problem
Details
     

 03-11-2008
2.00
Drill & cleco wing 1/8", tack rivet rear top skin
Details
       

 03-10-2008
5.00
Finish drill 3/32" & cleco R wing top rear skin to
Details
       

 03-10-2008
1.50
Continue drilling top rear skin
Details
     

 03-07-2008
3.00
Begin drilling 3/32 & cleco top rear skin
Details
       

 03-06-2008
1.00
Readjust spar angle using template
Details
     

 03-06-2008
1.00
Cut plywood fuselage templates
Details
       

 03-06-2008
0.00
Continuation of template cut entry
Details

 03-05-2008
2.00
Plan wing mount for gascolator
Details
     

 03-05-2008
2.00
Level wing skeleton and position top rear skin
Details
       

 03-02-2008
3.00
Rivet right wing skeleton
Details
       

 03-01-2008
6.00
Fab 2 pcs of new design pump mount
Details
       

 03-01-2008
0.00
Continued 3/1 entry because of Kitlog Bug
Details

 02-28-2008
1.00
Mock up & test new fuel pump channel
Details
       

 02-27-2008
6.00
Build wing fuel pump mounting channel
Details
       

 02-26-2008
5.00
Deburr, scour, clean, prime R-wing skeleton joint
Details

 02-25-2008
2.00
Cut rear spar for aileron control rod
Details
       

 02-24-2008
2.00
Aileron control rod hole placement
Details
       

 02-23-2008
2.00
Drill #20 & cleco rear ribs
Details
       

 02-22-2008
4.50
Drill & cleco the the rear spar to the ribs
Details
       

 02-22-2008
1.50
Drill & cleco right rear spar doubler
Details
     

 02-21-2008
4.00
Drill & cleco nose ribs to right spar
Details
       

 02-20-2008
2.00
Pilot drill 3/32" nose rib angles
Details
       

 02-20-2008
3.00
Drill & cleco nose ribs1-4 to spar angles
Details
       

 02-18-2008
4.00
Drill & cleco rear ribs to spar
Details
       

 02-17-2008
1.97
Drill & cleco stiffeners to rear ribs 6-9
Details
       

 02-15-2008
0.70
Lay out nose rivet pitch on right spar
Details
       

 02-14-2008
3.00
Mark spar & ribs, clamp ribs to spar
Details
       

 02-12-2008
2.00
Rivet stiffeners, etc., to ribs
Details

 02-11-2008
1.00
Cleco ribs & stiffeners, etc.
Details

 02-10-2008
3.00
Scour, wash, and prime rib parts
Details
       

 02-07-2008
2.00
Build, drill, cleco hole cover plates
Details
     

 02-07-2008
2.00
Build 2 light-channels for land/taxi lights
Details
       

 02-07-2008
2.00
Bend tests with HF brake
Details
     

 02-06-2008
6.00
Drill rib stiffeners, deburr, & scour
Details
       

 02-04-2008
3.00
Remake wing rib stiffeners
Details
       

 02-04-2008
0.00
KitlogPro bug work around
Details
       

 02-01-2008
5.00
Drill & cleco bellcrank supports, make rib stiffen
Details
       

 01-31-2008
2.50
Drill & cleco bell crank support channel
Details
       

 01-30-2008
4.50
Deburr rear ribs, build aileron bell crank support
Details
       

 01-29-2008
4.00
Deburr nose ribs, notch ribs 1-3
Details
       

 01-28-2008
4.00
Drill, cleco, & rivet wing spar tips to main spars
Details
       

 01-27-2008
3.00
Rivet aileron trim tab in place
Details
       

 01-26-2008
3.00
Disassemble aileron trim, deburr, etc
Details
       

 01-25-2008
3.00
Connect servo, drill channel
Details
       

 01-23-2008
3.00
Cut & Adjust aileron trim tab control rod
Details
       

 01-17-2008
3.00
Servo & control horn install
Details
       

 01-16-2008
3.00
Drill 3/32 & cleco aileron trim channel
Details
       

 01-15-2008
5.00
Cut R aileron for trim tab, drill trim tab for hin
Details
       

 01-13-2008
4.00
Assemble and rivet ailerons
Details
       

 01-12-2008
4.00
Prime aileron parts
Details
     

 01-10-2008
1.00
Drill R Aileron #30 & attach horn
Details
     

 01-09-2008
3.00
Aileron control horns, right aileron
Details
       

 01-07-2008
0.00
Drill & cleco left aileron
Details

 01-07-2008
0.00
Drill & cleco left aileron
Details

 01-07-2008
4.00
Drill & cleco left aileron
Details
       

 01-05-2008
4.00
Measure beam and work table flatness
Details
       

 01-04-2008
1.00
Deburr aileron parts
Details

 01-03-2008
3.00
Reassemble and rivet flaps
Details
     

 01-03-2008
0.00
Kitlog Pro Bug--Appended entry
Details

 01-02-2008
3.00
Deburr & prime flaps
Details
     

 01-01-2008
3.50
Drill #20 R Flap, disassemble, deburr L flap
Details

 12-30-2007
4.00
Drill R flap to #30, correct twist
Details
       

 12-29-2007
6.00
Drill #40 & cleco the right flap
Details
       

 12-28-2007
3.00
Drill and cleco left flap for A5 rivets
Details
       

 12-23-2007
5.00
Attach hinge to left flap
Details
       

 12-23-2007
0.00
2nd entry for 12/23 because of bug in Kitlog Pro 2
Details

 12-21-2007
0.00
Missing data because of Kitlog Pro Bug
Details

 12-21-2007
4.00
Drill #40 left flap & cleco
Details
       

 12-14-2007
1.00
Hang Rudder, Stabilizer, & Elevator from the ceili
Details
     

 12-13-2007
3.00
Button up the elevator
Details
       

 12-11-2007
0.00
KitLog Pro Bug Work Around
Details

 12-11-2007
6.00
Attach connectors to the servo & begin install in
Details
       

 12-07-2007
4.00
Complete riveting bottom of elevator, work on wiri
Details
     

 12-06-2007
3.00
Reassemble elevator & rivet bottom side
Details

 12-05-2007
4.00
Disassemble, deburr, & prime elevator
Details

 12-04-2007
4.00
Install servo and check operation
Details
       

 12-02-2007
4.00
Assemble elevator, and drill holes to final diamet
Details

 11-29-2007
3.00
Install elevator trim tab hinge
Details

 11-22-2007
3.00
Drill and cleco elevator cut out channel to elevat
Details
       

 11-14-2007
6.00
Attach elevator horns to elevator
Details
       

 11-13-2007
5.00
Drill hinge & skin, begin horn installation
Details
       

 11-11-2007
6.00
Drill and cleco the FTTs to the stab
Details
       

 11-10-2007
2.00
Attach extrusions to end ribs, check level
Details

 11-09-2007
4.00
Drill & cleco hinge to elevator
Details

 11-01-2007
2.00
Initiate FTT attachment to stab
Details
       

 11-01-2007
2.00
Consult w/ ZAC on stab/elevator building sequence
Details

 10-28-2007
4.00
Re-assembled stab and riveted
Details
     

 10-27-2007
1.00
Deburr, clean, and prime stab. top skin & Skeleton
Details

 10-25-2007
2.00
Drill the trailing edge of the stab & elevator hin
Details
     

 10-24-2007
2.00
Assemble Hangar Days Dwg Notebook
Details
     

 08-26-2007
3.00
Drill stabilizer top skin for front spar & ribs, i
Details
       

 08-24-2007
4.00
Press stab top skin into place, check for twist
Details
       

 08-22-2007
4.00
Rivet stabilizer bottom skin
Details
       

 08-21-2007
1.00
Deburr & scour the stab skin
Details
     

 08-20-2007
3.00
Drill and cleco stab skin to rear spar-3
Details
       

 08-18-2007
2.00
Drill and cleco stab skin to rear spar-2
Details
       

 08-06-2007
2.00
Drill and cleco stab skin to rear spar-1
Details

 08-04-2007
1.50
Deburr the stabilizer skin and attach to skeleton
Details
     

 08-04-2007
2.50
Clamp the skeleton to the work bench
Details
       

 07-22-2007
2.00
Clean stab parts and prime joint areas
Details

 07-21-2007
2.00
Drill out skeleton holes, disassemble, deburr
Details

 07-20-2007
3.00
Drill cleco rear spar to stabilizer ribs
Details
       

 07-18-2007
2.00
Re-drill & Cleco elevator skin
Details
       

 07-18-2007
2.00
Make new rear spar attachment, drill & cleco
Details

 07-18-2007
3.00
Drill & cleco the stabilizer ribs to the front spa
Details
       

 07-17-2007
2.00
Try to eliminate twist in elevator
Details
       

 07-16-2007
2.00
Drill &Cleco the elevator skin to the skeleton
Details
       

 07-11-2007
3.00
Assemble center ribs of elevator
Details
     

 07-09-2007
4.00
Stab rear spar doubler and attachment
Details
       

 07-08-2007
5.00
Drill & clecoe stabilizer front spar
Details
       

 07-02-2007
3.00
Rivet rudder skin to skeleton
Details
       

 07-02-2007
2.00
Assemble rudder skeleton
Details
       

 07-01-2007
3.00
ScotchBrite-again, wash, prime joint areas
Details
       

 07-01-2007
3.00
ScotchBrite the joint areas. Prepare and prime.
     

 06-29-2007
2.00
Unclecoe rudder; Trim nose skin, ScotchBrite joint
Details

 06-24-2007
3.00
Drill holes in rudder nose skin
Details
       

 06-06-2007
3.00
Insert nose skin for drilling
Details
       

 03-07-2007
2.00
Finish shelf on work bench, add doublers
Details
       

 03-06-2007
7.00
Build storage shelving, add shelf to workbench
Details
       

 03-05-2007
4.00
Build storage shelving
Details
       

 03-02-2007
2.00
Moved full kit to shop
Details
       

 02-28-2007
2.33
Drill and cleco aft rudder skin
Details
       

 02-27-2007
1.50
Drill and cleco top rib, fit aft skin
Details
       

 02-25-2007
1.00
Drill & Cleco nose rib

 02-24-2007
3.00
Rudder spar doubler + 2 ribs
Details
     

 02-16-2007
20.00
Build Table
Details
       










Copyright © 2001-2019 Matronics. All Rights Reserved.