KitLog pro

Powered By Kitlog Pro v2.0

Terrences Web Site
Work Logs Found: 93
Category Work Time: 247 Hours
 Date
Hours
Work Log Summary

Details

 03-06-2017
8.00
Drill holes for new left spar nose rib attachments
Details
       

 02-12-2015
4.00
Drill new angles for NR#2
Details
       

 03-13-2010
4.00
Remove the rivets in the wing skeleton
Details
       

 11-25-2009
3.00
Remove clecoed skins, clear off work table
Details
       

 07-26-2009
3.00
Form sample of Z-angle
Details
       

 06-29-2008
1.00
Check diameter of main spar bolt holes
Details
       

 04-06-2008
1.00
Drill new holes for NR#4
Details
     

 04-04-2008
3.00
Add shims to move NR#7
Details
       

 04-03-2008
1.00
Positioned nose skin--problems with prepunched hol
Details
       

 04-02-2008
2.00
Drill holes for gas line, position nose skin
Details
     

 04-01-2008
2.00
Drill main spar pilot holes, etc.
Details
       

 03-30-2008
5.00
Drill remaining 3/32" holes in bottom skin
Details
       

 03-29-2008
4.00
Drill & cleco bottom rear skin
Details
     

 03-27-2008
2.00
Check wing twist, start drilling bottom skin
Details
       

 03-26-2008
0.00
Continue 3/26 entry: Kitlog Pro BUG
Details

 03-26-2008
2.00
Adjust positon of bottom rear skin
Details
       

 03-25-2008
2.00
Fuel system & bottom rear skin
Details
       

 03-24-2008
3.00
Redesign and build doublers to reinforce tie down
Details
       

 03-23-2008
2.00
Design doublers for tie down ring
Details
     

 03-20-2008
3.00
Rivet gascolator channel, etc.
Details
       

 03-19-2008
0.00
Continue gascolator channel
Details
       

 03-19-2008
4.00
Begin build of gascolator mount channel
Details
       

 03-18-2008
2.00
Put lightening holes in landing light channels
Details
       

 03-15-2008
1.50
Mark rib stations on spars
Details

 03-13-2008
2.00
Drill out rib 9; drill replacement0
Details

 03-12-2008
2.00
Turn wing upside down and level
Details
       

 03-12-2008
0.50
Bottom rear skin problem
Details
     

 03-11-2008
2.00
Drill & cleco wing 1/8", tack rivet rear top skin
Details
       

 03-10-2008
5.00
Finish drill 3/32" & cleco R wing top rear skin to
Details
       

 03-10-2008
1.50
Continue drilling top rear skin
Details
     

 03-07-2008
3.00
Begin drilling 3/32 & cleco top rear skin
Details
       

 03-06-2008
1.00
Readjust spar angle using template
Details
     

 03-06-2008
1.00
Cut plywood fuselage templates
Details
       

 03-06-2008
0.00
Continuation of template cut entry
Details

 03-05-2008
2.00
Plan wing mount for gascolator
Details
     

 03-05-2008
2.00
Level wing skeleton and position top rear skin
Details
       

 03-02-2008
3.00
Rivet right wing skeleton
Details
       

 03-01-2008
6.00
Fab 2 pcs of new design pump mount
Details
       

 03-01-2008
0.00
Continued 3/1 entry because of Kitlog Bug
Details

 02-28-2008
1.00
Mock up & test new fuel pump channel
Details
       

 02-27-2008
6.00
Build wing fuel pump mounting channel
Details
       

 02-26-2008
5.00
Deburr, scour, clean, prime R-wing skeleton joint
Details

 02-25-2008
2.00
Cut rear spar for aileron control rod
Details
       

 02-24-2008
2.00
Aileron control rod hole placement
Details
       

 02-23-2008
2.00
Drill #20 & cleco rear ribs
Details
       

 02-22-2008
4.50
Drill & cleco the the rear spar to the ribs
Details
       

 02-22-2008
1.50
Drill & cleco right rear spar doubler
Details
     

 02-21-2008
4.00
Drill & cleco nose ribs to right spar
Details
       

 02-20-2008
2.00
Pilot drill 3/32" nose rib angles
Details
       

 02-20-2008
3.00
Drill & cleco nose ribs1-4 to spar angles
Details
       

 02-18-2008
4.00
Drill & cleco rear ribs to spar
Details
       

 02-17-2008
1.97
Drill & cleco stiffeners to rear ribs 6-9
Details
       

 02-15-2008
0.70
Lay out nose rivet pitch on right spar
Details
       

 02-14-2008
3.00
Mark spar & ribs, clamp ribs to spar
Details
       

 02-12-2008
2.00
Rivet stiffeners, etc., to ribs
Details

 02-11-2008
1.00
Cleco ribs & stiffeners, etc.
Details

 02-10-2008
3.00
Scour, wash, and prime rib parts
Details
       

 02-07-2008
2.00
Build, drill, cleco hole cover plates
Details
     

 02-07-2008
2.00
Build 2 light-channels for land/taxi lights
Details
       

 02-06-2008
6.00
Drill rib stiffeners, deburr, & scour
Details
       

 02-04-2008
3.00
Remake wing rib stiffeners
Details
       

 02-04-2008
0.00
KitlogPro bug work around
Details
       

 02-01-2008
5.00
Drill & cleco bellcrank supports, make rib stiffen
Details
       

 01-31-2008
2.50
Drill & cleco bell crank support channel
Details
       

 01-30-2008
4.50
Deburr rear ribs, build aileron bell crank support
Details
       

 01-29-2008
4.00
Deburr nose ribs, notch ribs 1-3
Details
       

 01-28-2008
4.00
Drill, cleco, & rivet wing spar tips to main spars
Details
       

 01-27-2008
3.00
Rivet aileron trim tab in place
Details
       

 01-26-2008
3.00
Disassemble aileron trim, deburr, etc
Details
       

 01-25-2008
3.00
Connect servo, drill channel
Details
       

 01-23-2008
3.00
Cut & Adjust aileron trim tab control rod
Details
       

 01-17-2008
3.00
Servo & control horn install
Details
       

 01-16-2008
3.00
Drill 3/32 & cleco aileron trim channel
Details
       

 01-15-2008
5.00
Cut R aileron for trim tab, drill trim tab for hin
Details
       

 01-13-2008
4.00
Assemble and rivet ailerons
Details
       

 01-12-2008
4.00
Prime aileron parts
Details
     

 01-10-2008
1.00
Drill R Aileron #30 & attach horn
Details
     

 01-09-2008
3.00
Aileron control horns, right aileron
Details
       

 01-07-2008
0.00
Drill & cleco left aileron
Details

 01-07-2008
0.00
Drill & cleco left aileron
Details

 01-07-2008
4.00
Drill & cleco left aileron
Details
       

 01-04-2008
1.00
Deburr aileron parts
Details

 01-03-2008
3.00
Reassemble and rivet flaps
Details
     

 01-03-2008
0.00
Kitlog Pro Bug--Appended entry
Details

 01-02-2008
3.00
Deburr & prime flaps
Details
     

 01-01-2008
3.50
Drill #20 R Flap, disassemble, deburr L flap
Details

 12-30-2007
4.00
Drill R flap to #30, correct twist
Details
       

 12-29-2007
6.00
Drill #40 & cleco the right flap
Details
       

 12-28-2007
3.00
Drill and cleco left flap for A5 rivets
Details
       

 12-23-2007
5.00
Attach hinge to left flap
Details
       

 12-23-2007
0.00
2nd entry for 12/23 because of bug in Kitlog Pro 2
Details

 12-21-2007
0.00
Missing data because of Kitlog Pro Bug
Details

 12-21-2007
4.00
Drill #40 left flap & cleco
Details
       










Copyright © 2001-2018 Matronics. All Rights Reserved.