Date
|
Hours
|
Work Log Summary
|
Details
|
11-20-2011
|
3.00
|
L/E: Rivetted to main spar
|
Details
|
|
|
11-19-2011
|
2.00
|
F/Tanks: Prepped baffle for installation
|
Details
|
|
|
11-14-2011
|
3.00
|
T/S: Dimpled all top skins, Installed Aileron Bell
|
Details
|
|
|
11-12-2011
|
3.00
|
L/E: Rivetted leading edges
|
Details
|
|
|
11-09-2011
|
3.00
|
T/S: Deburred all top skins
|
Details
|
|
|
11-08-2011
|
1.00
|
T/S: Removing plastic in prep for debur
|
Details
|
|
|
11-07-2011
|
1.00
|
F/Tanks: Double check pro-seal
|
Details
|
|
|
11-06-2011
|
1.50
|
F/Tanks: Riveted leading edge support brackets
|
Details
|
|
|
11-03-2011
|
0.50
|
Continued dimpling rear spar
|
Details
|
|
|
11-01-2011
|
1.00
|
Dimpled Rear Spar
|
Details
|
|
|
10-31-2011
|
2.00
|
Coutersunk Main spar for wing skin rivets
|
Details
|
|
|
10-30-2011
|
2.00
|
Coutersunk Main spar for wing skin rivets
|
Details
|
|
|
10-27-2011
|
1.50
|
Dimpling main ribs
|
Details
|
|
|
10-26-2011
|
1.50
|
Started dimpling wing understructure
|
Details
|
|
|
10-24-2011
|
2.00
|
L T/S: Scarfing corners on Top Skins
|
Details
|
|
|
10-23-2011
|
2.00
|
L/E: Priming and rivetting platenuts to joint plat
|
Details
|
|
|
10-22-2011
|
1.50
|
L/E: Drilled platenuts on Joint Plates
|
Details
|
|
|
10-16-2011
|
0.50
|
L/E: Finished dimpling skins
|
Details
|
|
|
09-26-2011
|
1.50
|
L/E: Removed plastic and dimpled skin
|
Details
|
|
|
09-22-2011
|
1.50
|
R L/E: Deburr skin and dimple ribs and joint plate
|
Details
|
|
|
09-03-2011
|
1.50
|
L L/E: Deburr skin and dimple ribs and joint plate
|
Details
|
|
|
07-24-2011
|
2.00
|
R F/Tank: Installed Cap. Senders and outboard rib
|
Details
|
|
|
05-29-2011
|
1.00
|
R F/Tank: Rivetted inboard most rib
|
Details
|
|
|
05-22-2011
|
1.00
|
R F/Tank: Prosealed vent pipe in place
|
Details
|
|
|
05-14-2011
|
0.50
|
R F/Tank: Vent pipe bending (inboard)
|
Details
|
|
|
05-08-2011
|
0.50
|
R F/Tank: Fitted vent pipe
|
Details
|
|
|
05-01-2011
|
1.00
|
R F/Tank: Rivetted ribs and Filler Cap housing
|
Details
|
|
|
03-27-2011
|
1.00
|
R F/Tank: Fay sealed ribs in place
|
Details
|
|
|
02-13-2011
|
1.00
|
L F/Tank: Installed outboard rib and extra pro-sea
|
Details
|
|
|
02-03-2011
|
2.00
|
L F/Tank: Installed Cap. senders and inboard rib
|
Details
|
|
|
02-01-2011
|
0.50
|
L F/Tank: Vent pipe bending
|
Details
|
|
|
01-27-2011
|
1.00
|
L F/Tank: Fitted the vent pipe
|
Details
|
|
|
01-25-2011
|
2.00
|
L F/Tank: Rivetted ribs and Filler cap
|
Details
|
|
|
01-18-2011
|
1.50
|
L F/Tank: Rivetted Stiffeners and Drain Plug
|
Details
|
|
|
01-17-2011
|
1.00
|
R F/Tank: Rivetted stiffeners and drain plug
|
Details
|
|
|
01-15-2011
|
1.50
|
F/Tanks: Prep for proseal
|
Details
|
|
|
01-13-2011
|
2.00
|
R F/Tank: Dimpled skin and prep for pro-seal
|
Details
|
|
|
01-12-2011
|
1.00
|
R F/Tank: Dimpled ribs and stiffeners
|
Details
|
|
|
01-11-2011
|
1.00
|
L F/Tank: Dimple skin
|
Details
|
|
|
01-10-2011
|
2.00
|
L F/Tank: Disassemble and deburr
|
Details
|
|
|
11-08-2010
|
0.50
|
F/Tanks: Safety wired trap doors in place
|
Details
|
|
|
11-07-2010
|
1.50
|
L F/Tank: Flop Tube anti hang-up
|
Details
|
|
|
11-01-2010
|
1.00
|
R F/Tank: Manufactured vent pipe clamp
|
Details
|
|
|
10-30-2010
|
4.00
|
R F/Tank: Filler Camp, Drain Plug and Cap.plates
|
Details
|
|
|
10-27-2010
|
2.00
|
L F/Tanks: Vent Pipe Clamp and fit Capacitance pla
|
Details
|
|
|
10-25-2010
|
2.00
|
F/Tanks: Fitting Left Drain Plug and Filler Cap
|
Details
|
|
|
10-24-2010
|
2.50
|
F/Tanks: Capacitance Fuel Sender Installation
|
Details
|
|
|
10-23-2010
|
1.00
|
F/Tanks: Inboard Bay Trap Door (Left)
|
Details
|
|
|
10-22-2010
|
1.00
|
F/Tanks: Inboard Bay Trap Door (Right)
|
Details
|
|
|
10-21-2010
|
0.50
|
F/Tanks: Inboard Bay Trap Doors
|
Details
|
|
|
10-20-2010
|
2.00
|
F/Tanks: Inspection holes
|
Details
|
|
|
10-19-2010
|
1.00
|
F/Tanks: Inboard Ribs Inspection Hole Cut-Outs
|
Details
|
|
|
10-18-2010
|
2.00
|
F/Tanks: T405 Attachment Brackets
|
Details
|
|
|
10-11-2010
|
3.00
|
F/Tanks: T405 Attachment Brackets
|
Details
|
|
|
10-10-2010
|
4.00
|
F/Tanks: Debur skins/ribs, start on T405 brackets
|
Details
|
|
|
10-09-2010
|
1.00
|
F/Tanks: Countersinking Skins and drilling stiffen
|
Details
|
|
|
10-07-2010
|
1.00
|
R F/Tank: Countersink skins
|
Details
|
|
|
10-05-2010
|
1.00
|
Z Brackets: Drilling to right tank baffle
|
Details
|
|
|
10-04-2010
|
1.00
|
Z Brackets: Mount Right Fuel Tank
|
Details
|
|
|
10-03-2010
|
1.00
|
R F/Tank: Cleco together
|
Details
|
|
|
09-12-2010
|
0.50
|
F/Tanks: Prep stiffeners
|
Details
|
|
|
09-06-2010
|
1.00
|
L F/Tank: drilling and cut all stiffeners
|
Details
|
|
|
09-05-2010
|
1.50
|
L F/Tank: Drill W423 Joint Plate
|
Details
|
|
|
09-02-2010
|
0.00
|
Z Brackets-Fitting & drilling to Left Fuel Tank 4
|
Details
|
|
|
09-02-2010
|
0.00
|
Z Brackets-Fitting & drilling to Left Fuel Tank 3
|
Details
|
|
|
09-02-2010
|
0.00
|
Z Brackets-Fitting & drilling to Left Fuel Tank 2
|
Details
|
|
|
09-02-2010
|
2.00
|
Z Brackets-Fitting & drilling to Left Fuel Tank 1
|
Details
|
|
|
08-31-2010
|
3.00
|
Z Brackets - Priming and rivet nutplates
|
Details
|
|
|
08-30-2010
|
1.50
|
Z Bracket - countersinking and spar countersink
|
Details
|
|
|
08-29-2010
|
3.00
|
Bending Brake - Rebuild
|
Details
|
|
|
08-28-2010
|
1.50
|
Z brackets - drilling nutplates
|
Details
|
|
|
08-26-2010
|
0.50
|
Z Brackets - drilling to right spar
|
Details
|
|
|
08-15-2010
|
0.50
|
Z Brackets - drilling to left spar
|
Details
|
|
|
08-14-2010
|
1.00
|
Z Brackets ... cleco fuel tank skin
|
Details
|
|
|
08-14-2010
|
1.50
|
Z Brackets
|
Details
|
|
|
05-02-2010
|
0.00
|
Wing Stands: Photos after the fact
|
Details
|
|
|
05-01-2010
|
40.00
|
Wings stands, rigging, skins, drilling, leading ed
|
Details
|
|
|
04-18-2010
|
8.00
|
Rivet understructure together
|
Details
|
|
|
03-11-2010
|
1.00
|
Ribs: Priming
|
Details
|
|
|
03-10-2010
|
2.00
|
Disassemble understructure and debur
|
Details
|
|
|
03-08-2010
|
4.00
|
Clecoed understructure together
|
Details
|
|
|
02-28-2010
|
2.00
|
Wing Stands: Drilled feet and welded to uprights
|
Details
|
|
|
02-27-2010
|
2.00
|
Wing Stands: Cut uprights and shaped feet
|
Details
|
|
|
02-25-2010
|
4.00
|
Ribs: Fluting
|
Details
|
|
|
02-24-2010
|
4.00
|
Ribs: Fluting...
|
Details
|
|
|
02-23-2010
|
1.00
|
Ribs: Fluting
|
Details
|
|
|
02-22-2010
|
4.00
|
Ribs: Bending Flanges to 90 Deg.
|
Details
|
|
|
02-21-2010
|
8.00
|
Ribs: Deburring...
|
Details
|
|
|
01-26-2010
|
1.50
|
Ribs: Deburring...
|
Details
|
|
|
01-25-2010
|
4.00
|
Ribs: Deburring
|
Details
|
|
|
01-24-2010
|
1.50
|
Rear Spars: Rivetting and starting on Ribs
|
Details
|
|
|
01-23-2010
|
1.00
|
Rear Spars: 2 - Prep and Priming
|
Details
|
|
|
01-23-2010
|
1.00
|
Rear Spars: 1 - Reinforcement fork and doublers
|
Details
|
|
|
01-22-2010
|
1.00
|
Rear Spars: Aileron push rod cut-outs
|
Details
|
|
|
01-21-2010
|
0.50
|
Rear Spars: Match drill reinforcement plates
|
Details
|
|
|
01-19-2010
|
3.00
|
Rear Spars: Edge Prepping
|
Details
|
|
|
01-18-2010
|
0.50
|
Tie Down Manufacture - 3
|
Details
|
|
|
01-17-2010
|
0.00
|
Tie Down Manufacture - 2 (cont)
|
Details
|
|
|
01-17-2010
|
3.00
|
Tie Down Manufacture - 2
|
Details
|
|
|
01-12-2010
|
1.00
|
Tie Down Manufacture - 1
|
Details
|
|
|
01-11-2010
|
2.00
|
Rivet Web Platenuts, start on Tie Down Spacers
|
Details
|
|
|
01-09-2010
|
1.00
|
Rivet Flange Platenuts to spar
|
Details
|
|
|
01-07-2010
|
4.00
|
Countersink & Prime spars, rivet platenuts
|
Details
|
|
|
01-05-2010
|
3.00
|
Countersink Main Spars
|
Details
|
|
|
12-23-2009
|
0.00
|
Wings Arrive
|
|
|
|
12-14-2009
|
1.00
|
HS Tips: Drill, countersink and rivet
|
Details
|
|
|
12-13-2009
|
1.00
|
HS Tips: Re-enforcing with aluminium strips
|
Details
|
|
|
12-12-2009
|
3.00
|
R-Elev Tip: Re-enforcing, balancing and rivetting
|
Details
|
|
|
12-09-2009
|
1.50
|
Elev Tips: Re-enforcing tips and match drilling
|
Details
|
|
|
12-07-2009
|
2.00
|
HS & Elev Tips: Final sanding, removing box tape
|
Details
|
|
|
12-06-2009
|
1.00
|
HS & Elev Tips: Pinhole filling, sanding, priming
|
Details
|
|
|
12-05-2009
|
1.50
|
HS & Elev Tips: Sanding, priming, repeat
|
Details
|
|
|
12-04-2009
|
1.50
|
L-HS & L Elev Tip: Sanding, shaping, strengthening
|
Details
|
|
|
12-03-2009
|
1.50
|
L-HS & L-Elev Tips: Sanding and re-shaping
|
Details
|
|
|
11-29-2009
|
0.50
|
L-HS Tip: Remove and rebuild elev skin "joggle"
|
Details
|
|
|
11-29-2009
|
1.00
|
L-Elev Tip: Remove and rebuild elev skin "joggle"
|
Details
|
|
|
11-28-2009
|
0.50
|
L-Elev Tip: Sanding front face to shape
|
Details
|
|
|
11-27-2009
|
0.50
|
L-HS & L-Elev Tips: Sanding and floxing
|
Details
|
|
|
11-26-2009
|
1.00
|
L-HS Tip: Prep and glass in rear "face"
|
Details
|
|
|
11-26-2009
|
2.00
|
L-Elev Tip: Prep and layup front "face"
|
Details
|
|
|
11-24-2009
|
1.00
|
R-HS & R-Elev: Pinhole filling, sanding, priming
|
Details
|
|
|
11-23-2009
|
1.50
|
R-HS & R Elev: Balancing, priming and more floxing
|
Details
|
|
|
11-18-2009
|
1.50
|
R-HS & R-Elev tip: Sanded, ballooned and floxed
|
Details
|
|
|
11-17-2009
|
1.00
|
R-HS Tip: Sand down joggle and flox
|
Details
|
|
|
11-15-2009
|
0.50
|
R-HS Tip: Another layup
|
Details
|
|
|
11-14-2009
|
0.50
|
R-HS & Elev tip: Sanding to shape
|
Details
|
|
|
11-08-2009
|
0.50
|
R-HS Tip: Test fit and make flox gusset inside
|
Details
|
|
|
11-08-2009
|
1.00
|
R-Elev Tip: Sand tip joggle and micro balloon
|
Details
|
|
|
11-07-2009
|
1.00
|
R-HS Tip: Construct Foam Rib and Glass Over
|
Details
|
|
|
11-07-2009
|
0.50
|
R-Elev Tip: Remove and rebuild elev tip "joggle"
|
Details
|
|
|
11-01-2009
|
0.50
|
R-HS Tip: Initial fitting and drilling to skin
|
Details
|
|
|
11-01-2009
|
1.50
|
R-Elev Tip: Sanding and shaping
|
Details
|
|
|
10-29-2009
|
0.00
|
R-Elev Tip: Glass in counterweight -Part 2-
|
Details
|
|
|
10-29-2009
|
1.50
|
R-Elev Tip: Glass in counterweight -Part 1-
|
Details
|
|
|
10-26-2009
|
0.50
|
L-Elev: Fitted Trim Servo
|
Details
|
|
|
10-26-2009
|
1.50
|
Elev Tips: Cut to size, test fitted and drilled to
|
Details
|
|
|
10-25-2009
|
2.00
|
Elev: Mounting and aligning elevators to H-Stab
|
Details
|
|
|
10-22-2009
|
1.50
|
R-Elev: Rolled leading edge
|
Details
|
|
|
10-18-2009
|
2.00
|
L-Elev: Rolling leading edge
|
Details
|
|
|
10-17-2009
|
2.50
|
L-Elev: Rivet skin to understructure and Trim Tab
|
Details
|
|
|
10-15-2009
|
2.00
|
R-Elev: Rivet skin to understructure
|
Details
|
|
|
10-14-2009
|
1.00
|
Elev: Inspection and Trim Tab Rivetting
|
Details
|
|
|
10-12-2009
|
0.50
|
L-Elev: Trim Tab Hinge
|
Details
|
|
|
10-11-2009
|
0.00
|
New Fuse/ Engine/ Prop - I mean Garage/Kitchen/Stu
|
Details
|
|
|
10-26-2008
|
0.50
|
L-Elev: Rivet Understructure
|
Details
|
|
|
10-18-2008
|
1.00
|
L-Elev: Priming
|
Details
|
|
|
10-14-2008
|
1.00
|
L-Elev: Trim Tab construction
|
Details
|
|
|
10-13-2008
|
1.50
|
L-Elev: Rivet spar and start trim tab construction
|
Details
|
|
|
10-12-2008
|
0.00
|
L-Elev: Trim tab bend - Part 2
|
Details
|
|
|
10-12-2008
|
2.00
|
L-Elev: Trim tab bend - Part 1
|
Details
|
|
|
10-12-2008
|
1.00
|
L-Elev: Elevator tab folding
|
Details
|
|
|
10-11-2008
|
0.50
|
L-Elev: Trim Servo mounting bracket
|
Details
|
|
|
10-04-2008
|
1.50
|
L-Elev: Trim Servo skin doubler
|
Details
|
|
|
09-20-2008
|
2.00
|
L-Elev: Countersinking, Dimpling, Bevelling and Tr
|
Details
|
|
|
09-16-2008
|
1.50
|
L-Elev: Dimple and countersink
|
Details
|
|
|
09-14-2008
|
1.50
|
L-Elev: Complete understructure, match drill, debu
|
Details
|
|
|
09-09-2008
|
0.50
|
L-Elev: Construction of understructure
|
Details
|
|
|
09-08-2008
|
0.50
|
R-Elev: Rivet understructure
|
Details
|
|
|
09-07-2008
|
1.00
|
R-Elev: Priming
|
Details
|
|
|
09-05-2008
|
0.50
|
R-Elev: Initial rivetting of understructure
|
Details
|
|
|
08-23-2008
|
0.50
|
R-Elev: Edge prep, deburr and dimple
|
Details
|
|
|
08-22-2008
|
1.00
|
R-Elev: Countersink, bevel and deburr
|
Details
|
|
|
08-17-2008
|
1.50
|
R-Elev: Drill counterweight and match drill skin t
|
Details
|
|
|
03-31-2008
|
1.50
|
R-Elev: Beginning the understructure
|
Details
|
|
|
03-30-2008
|
0.50
|
Elev: Bending the trailing edges
|
Details
|
|
|
03-24-2008
|
1.50
|
L-Elev: Backriveting completed
|
Details
|
|
|
03-02-2008
|
1.00
|
R-Elev: Backriveting Stiffeners
|
Details
|
|
|
02-23-2008
|
1.00
|
Elev: Skin Prep and Backrivetting stiffeners
|
Details
|
|
|
02-09-2008
|
2.00
|
Elev: Edge Finishing, Dimpling and plastic strippi
|
Details
|
|
|
02-01-2008
|
0.50
|
R-Elev: Debur and edge finishing
|
Details
|
|
|
01-30-2008
|
1.00
|
L-Elev: Debur and edge finishing
|
Details
|
|
|
01-24-2008
|
1.50
|
Elev: Finished stiffeners and match drilled elevat
|
Details
|
|
|
01-19-2008
|
1.00
|
Elev: Left elevator stiffeners and right elevator
|
Details
|
|
|
01-17-2008
|
1.00
|
L-Elev: Cutting and marking of Stiffeners
|
Details
|
|
|
01-16-2008
|
1.00
|
R-Elev: Trimming and Edge Finishing Stiffeners
|
Details
|
|
|
01-13-2008
|
0.50
|
R-Elev: Marking and Trimming stiffeners
|
Details
|
|
|
11-23-2007
|
0.00
|
1 Hour Extreme Aerobatics - Extra 300
|
Details
|
|
|
11-21-2007
|
0.50
|
RD: Hang the rudder from VS
|
Details
|
|
|
11-18-2007
|
1.50
|
RD: Closed up leading edge
|
Details
|
|
|
11-12-2007
|
1.50
|
RD: Rolling the Leading Edge
|
Details
|
|
|
11-11-2007
|
2.50
|
RD: Pro-sealed and closed-up
|
Details
|
|
|
11-08-2007
|
0.50
|
RD: Inspection Complete
|
Details
|
|
|
11-06-2007
|
0.50
|
RD: Rivetting rudder control horn
|
Details
|
|
|
09-17-2007
|
2.00
|
RD: Rivetting spar and understructure
|
Details
|
|
|
09-09-2007
|
1.50
|
RD: Prepping and Priming
|
Details
|
|
|
09-04-2007
|
0.50
|
RD: Edge Finishing and Paint Prepping
|
Details
|
|
|
09-02-2007
|
3.00
|
RD: Disassemble, deburr and Dimple
|
Details
|
|
|
08-30-2007
|
2.00
|
RD: Bend Trailing edge
|
Details
|
|
|
08-28-2007
|
1.50
|
RD: Back-rivetting the rudder stiffeners
|
Details
|
|
|
07-08-2007
|
1.50
|
RD: Back-riveting rudder stiffeners
|
Details
|
|
|
07-05-2007
|
1.00
|
RD: Prepped for back-riveting
|
Details
|
|
|
07-04-2007
|
2.00
|
RD: Finished stiffeners and dimpled skin
|
Details
|
|
|
06-19-2007
|
1.00
|
RD: Match drilled top rib, final drilled spar web
|
Details
|
|
|
06-19-2007
|
0.50
|
Finished the Bending Break
|
Details
|
|
|
06-18-2007
|
3.00
|
Built a Bending Brake
|
Details
|
|
|
06-17-2007
|
1.00
|
RD: Clecoing and clamping of spar
|
Details
|
|
|
06-17-2007
|
0.00
|
First flip in an RV-8 --> PHWOAAR
|
Details
|
|
|
06-16-2007
|
1.50
|
RD: Trimmed R-710, Enlarged hinge hole on R-704
|
Details
|
|
|
06-14-2007
|
1.50
|
RD: Manufactured R-716 and R-717
|
Details
|
|
|
06-12-2007
|
1.50
|
RD: Debur and Dimple skin and R-815 Stiffeners
|
Details
|
|
|
06-07-2007
|
2.00
|
RD: Edge finished stiffeners, cleco'd and drilled
|
Details
|
|
|
06-04-2007
|
2.00
|
RD: Cut stiffeners to length and shape
|
Details
|
|
|
06-03-2007
|
2.00
|
Inspection and closing up both VS and HS
|
Details
|
|
|
06-02-2007
|
1.00
|
VS: Finish Riveting skin
|
Details
|
|
|
06-02-2007
|
0.00
|
Ready for my first inspection
|
Details
|
|
|
05-31-2007
|
2.00
|
VS: Fix mess & start riveting skin
|
Details
|
|
|
05-30-2007
|
1.50
|
VS: Riveted Rear Spar
|
Details
|
|
|
05-30-2007
|
1.50
|
VS: My first stuff up
|
Details
|
|
|
05-28-2007
|
1.50
|
VS: Primed understructure and skin inside
|
Details
|
|
|
05-27-2007
|
1.00
|
VS: Dimpled skin and prep'ed for priming
|
Details
|
|
|
05-26-2007
|
1.00
|
VS: Countersunk spar doubler
|
Details
|
|
|
05-25-2007
|
1.00
|
VS: Disassemble and edge finish
|
Details
|
|
|
05-24-2007
|
1.00
|
VS: Final drilled skin
|
Details
|
|
|
05-23-2007
|
1.00
|
VS: Completed Understructure
|
Details
|
|
|
05-22-2007
|
1.00
|
VS: Started on the vertical stab rear spar
|
Details
|
|
|
05-21-2007
|
3.00
|
HS: Finished riveting boths skins barring rear spa
|
Details
|
|
|
05-20-2007
|
1.50
|
HS: Shot both HS707 ribs to the skin
|
Details
|
|
|
05-18-2007
|
1.00
|
HS: More riveting of understructure
|
Details
|
|
|
05-17-2007
|
1.50
|
HS: Rivet outboard hinge brackets and shot my firs
|
Details
|
|
|
05-15-2007
|
4.00
|
HS: Prime and rivet understructure
|
Details
|
|
|
04-30-2007
|
2.00
|
HS: Deburr both HS skins and dimple on DRDT-2
|
Details
|
|
|
04-27-2007
|
1.50
|
HS: Dimple understructure with pneumatic squeezer
|
Details
|
|
|
04-26-2007
|
1.50
|
HS: Deburr and edge finish understructure
|
Details
|
|
|
04-25-2007
|
1.00
|
HS: Final drill 810, 814 and deconstruct
|
Details
|
|
|
|
04-24-2007
|
2.00
|
HS: (Right) Final drill Ribs, Spars and Skin
|
Details
|
|
|
|
04-23-2007
|
2.00
|
HS: (Right) Construction of Underlying structure
|
Details
|
|
|
04-22-2007
|
2.00
|
HS: Final drill skin and forward spar stiffeners
|
Details
|
|
|
|
04-19-2007
|
2.00
|
HS: Drill Ribs and Spars
|
Details
|
|
|
|
04-18-2007
|
2.50
|
HS: Construction of underlying structure
|
Details
|
|
|
|
04-17-2007
|
2.00
|
HS: Rib Preperations
|
Details
|
|
|
|
04-15-2007
|
2.00
|
HS: Front Spar and Ribs
|
Details
|
|
|
|
04-14-2007
|
2.00
|
HS: Front Spar Stiffeners
|
Details
|
|
|
04-13-2007
|
2.00
|
Setup Compressor
|
Details
|
|
|
|
04-10-2007
|
2.00
|
HS: Rear Spar
|
Details
|
|
|
04-09-2007
|
2.50
|
HS: Finished HS-609PP prepping
|
Details
|
|
|
|
04-03-2007
|
2.50
|
HS: Prepped HS-609PP
|
Details
|
|
|
|
03-31-2007
|
8.00
|
Built a workbench
|
Details
|
|
|
03-24-2007
|
6.00
|
More shop cleanup
|
Details
|
|
|
|
03-17-2007
|
4.00
|
Built a Dimpling Table
|
Details
|
|
|
|
03-10-2007
|
8.00
|
Cleaned out the Garage
|
Details
|
|
|
|
02-28-2007
|
0.00
|
Kit arrives...
|
Details
|
|
