Date
|
Hours
|
Work Log Summary
|
Details
|
02-12-2009
|
1.50
|
Empennage Fairing
|
Details
|
|
|
|
01-29-2009
|
4.00
|
Rear seat back Completion
|
Details
|
|
|
|
01-22-2009
|
1.50
|
Rear headphone jacks.
|
Details
|
|
|
|
01-14-2009
|
1.50
|
Finished fitting Tunnel covers.
|
Details
|
|
|
01-05-2009
|
2.00
|
finish baggage door
|
Details
|
|
|
12-30-2008
|
2.50
|
Baggage door install
|
Details
|
|
|
|
12-27-2008
|
3.10
|
Finish baggage corrugation prep.
|
Details
|
|
|
|
12-24-2008
|
0.70
|
rivet baggage cover
|
Details
|
|
|
12-23-2008
|
0.30
|
tailcone top skin
|
Details
|
|
|
|
12-23-2008
|
0.50
|
rivet nutplates to baggage floors
|
Details
|
|
|
|
12-23-2008
|
0.50
|
rivet baggage bulkhead
|
Details
|
|
|
|
12-23-2008
|
2.20
|
baggage corrugations
|
Details
|
|
|
|
12-21-2008
|
0.60
|
Upper baggage door Channel
|
Details
|
|
|
12-21-2008
|
0.70
|
Re position static source tubing
|
Details
|
|
|
|
12-21-2008
|
0.20
|
cleco baggage covers
|
Details
|
|
|
|
12-21-2008
|
0.30
|
baggage door seal channel
|
Details
|
|
|
12-19-2008
|
1.30
|
seat and baggage floors
|
Details
|
|
|
12-19-2008
|
0.70
|
baggage floors
|
Details
|
|
|
|
12-19-2008
|
0.30
|
baggage floors
|
Details
|
|
|
12-16-2008
|
2.00
|
seat and baggage floors
|
Details
|
|
|
11-18-2008
|
1.00
|
changed FPS system
|
Details
|
|
|
|
11-15-2008
|
0.50
|
miscellaneous wiring details
|
Details
|
|
|
|
11-03-2008
|
2.00
|
install strobe light wires
|
Details
|
|
|
|
11-03-2008
|
0.50
|
ap fuse wires
|
Details
|
|
|
|
11-01-2008
|
1.00
|
elevator trim wiring
|
Details
|
|
|
|
10-26-2008
|
2.50
|
A/P wiring
|
Details
|
|
|
|
10-25-2008
|
2.00
|
Dynon A/P roll kit
|
Details
|
|
|
|
10-22-2008
|
0.50
|
wire wrap fuel and brake lines
|
Details
|
|
|
|
10-22-2008
|
0.50
|
Fuel boost pump
|
Details
|
|
|
|
10-21-2008
|
1.50
|
finish control column adjustment.
|
Details
|
|
|
|
10-20-2008
|
1.50
|
control column adjustment
|
Details
|
|
|
|
10-19-2008
|
0.50
|
Test flap operation
|
Details
|
|
|
|
10-19-2008
|
2.00
|
control column install
|
Details
|
|
|
|
10-18-2008
|
4.00
|
finish flap tube install
|
Details
|
|
|
|
10-16-2008
|
1.50
|
flap tube install
|
Details
|
|
|
|
10-14-2008
|
2.00
|
Flap control tubes
|
Details
|
|
|
|
10-11-2008
|
3.30
|
Elevator and control systems
|
Details
|
|
|
|
10-09-2008
|
1.50
|
make and prime elevator pushrods
|
Details
|
|
|
|
10-07-2008
|
0.50
|
Seat back closeout
|
Details
|
|
|
|
10-07-2008
|
0.20
|
FPS holes
|
Details
|
|
|
|
10-07-2008
|
0.70
|
Elevator Idler brackets
|
Details
|
|
|
10-05-2008
|
1.00
|
Static Port Replacement
|
Details
|
|
|
|
09-17-2008
|
0.20
|
Intercom Jacks
|
Details
|
|
|
|
09-17-2008
|
1.50
|
|
Details
|
|
|
|
09-15-2008
|
1.50
|
Fished more wires
|
Details
|
|
|
|
09-13-2008
|
3.00
|
Wiring tail light and Ele. trim
|
Details
|
|
|
|
09-13-2008
|
1.50
|
stall buzzer
|
Details
|
|
|
09-10-2008
|
1.00
|
Strobe P/S
|
Details
|
|
|
|
09-10-2008
|
1.00
|
reattach vert stab.
|
Details
|
|
|
|
09-09-2008
|
2.00
|
More Wiring
|
Details
|
|
|
|
09-07-2008
|
1.00
|
Q1, P8 & P9
|
Details
|
|
|
|
08-30-2008
|
3.00
|
circuit breakers and terminal block
|
Details
|
|
|
08-28-2008
|
3.20
|
Rear Floor Pans (Passenger)
|
Details
|
|
|
08-28-2008
|
3.00
|
brake tubing
|
Details
|
|
|
08-23-2008
|
1.50
|
Pedals Assembly
|
Details
|
|
|
|
08-22-2008
|
2.50
|
Brake parts assembly
|
Details
|
|
|
|
08-21-2008
|
2.00
|
Brake Pedals
|
Details
|
|
|
|
08-15-2008
|
1.00
|
Layout and Firewall bushing
|
Details
|
|
|
|
08-15-2008
|
0.70
|
Fuel lines
|
Details
|
|
|
08-09-2008
|
1.00
|
lock set and close out panel rivets
|
Details
|
|
|
08-09-2008
|
1.00
|
Fuel Lines
|
Details
|
|
|
|
08-07-2008
|
2.50
|
Fuel Lines
|
Details
|
|
|
|
07-29-2008
|
1.00
|
Fuel Lines
|
Details
|
|
|
|
07-19-2008
|
3.00
|
Baggage door assembly
|
Details
|
|
|
|
07-18-2008
|
1.00
|
Baggage area parts
|
Details
|
|
|
|
07-16-2008
|
6.00
|
dimpling and riveting
|
Details
|
|
|
07-15-2008
|
3.20
|
Drilling Skins
|
Details
|
|
|
|
07-14-2008
|
2.00
|
Clecoing Tailcone
|
Details
|
|
|
|
07-13-2008
|
3.00
|
Prep for Tailcone Attachment
|
Details
|
|
|
07-09-2008
|
3.00
|
Brake lines
|
Details
|
|
|
07-08-2008
|
0.30
|
Upper FWD Fuselage Assembly
|
Details
|
|
|
07-07-2008
|
0.75
|
Step Installation.
|
Details
|
|
|
07-06-2008
|
4.50
|
Fuselage Side Skins
|
Details
|
|
|
07-04-2008
|
0.50
|
Mid Seat Rail Support Rivet.
|
Details
|
|
|
07-03-2008
|
2.30
|
FWD Ribs, Bulkheads and Bottom Skins
|
Details
|
|
|
|
07-02-2008
|
0.50
|
Mid Fuselage Ribs and Bottom Skins
|
Details
|
|
|
|
07-02-2008
|
0.50
|
Mid Fuselage Bulkheads
|
Details
|
|
|
|
07-02-2008
|
0.50
|
Firewall
|
Details
|
|
|
06-30-2008
|
2.50
|
Wing Tip Lights Right Side
|
Details
|
|
|
06-29-2008
|
4.50
|
Laying up HS and Rudder Fairings
|
Details
|
|
|
06-29-2008
|
1.50
|
Finish Left Wing Tip Lighting
|
Details
|
|
|
06-21-2008
|
2.50
|
Wing Tip Lighting Left Side
|
Details
|
|
|
|
06-15-2008
|
1.80
|
Wing Tip Rib
|
Details
|
|
|
06-10-2008
|
4.10
|
Prep and install nutplates
|
Details
|
|
|
06-01-2008
|
1.00
|
Nutplate attach
|
Details
|
|
|
|
05-31-2008
|
6.00
|
Trim Wing Tips
|
Details
|
|
|
|
05-29-2008
|
2.10
|
BC to Ail Pushrod Install. R
|
Details
|
|
|
|
05-28-2008
|
2.00
|
TT to BC Installation, BC to Ail. pushrod Install.
|
Details
|
|
|
05-26-2008
|
2.50
|
Torque Tube Installation
|
Details
|
|
|
05-25-2008
|
2.50
|
Torque tubes and bellcrank assembly
|
Details
|
|
|
|
05-24-2008
|
2.50
|
Torque Tube to BellCrank Pushrod
|
Details
|
|
|
05-23-2008
|
0.20
|
QB Flaps
|
Details
|
|
|
05-18-2008
|
1.00
|
Wing access plates
|
Details
|
|
|
05-18-2008
|
1.60
|
QB aileron completion L & R
|
Details
|
|
|
05-15-2008
|
2.00
|
Finish Riveting Left Bottom Skins
|
Details
|
|
|
05-14-2008
|
3.00
|
Rivet Left Bottom Skins
|
Details
|
|
|
05-12-2008
|
0.50
|
Finish Bottom OB Skins (Right)
|
Details
|
|
|
05-10-2008
|
3.00
|
Botton Wing Skins Riveting
|
Details
|
|
|
05-08-2008
|
2.00
|
Bottom Skin Rivet (R)
|
Details
|
|
|
05-07-2008
|
2.00
|
Bottom Wing Skins Prep for Riveting
|
Details
|
|
|
05-01-2008
|
1.30
|
Bottom Wing Skins
|
Details
|
|
|
|
04-27-2008
|
3.50
|
Bottom Wing Skins
|
Details
|
|
|
|
04-21-2008
|
2.00
|
Bottom Wing Skins
|
Details
|
|
|
|
04-20-2008
|
3.50
|
bottom wing skins (Right) some (left)
|
Details
|
|
|
|
04-14-2008
|
1.30
|
Bottom Wing Skins (Left)
|
Details
|
|
|
|
04-13-2008
|
1.50
|
Bottom Wing Skins
|
Details
|
|
|
|
04-12-2008
|
4.20
|
Dimple top wing skins and Rivet Gap Fairings
|
Details
|
|
|
|
04-07-2008
|
1.50
|
dimpling Top Wing Skins
|
Details
|
|
|
|
04-06-2008
|
1.00
|
Top Wing Skins
|
Details
|
|
|
|
04-06-2008
|
6.00
|
Flap gap Fairings, Dimple Skins
|
Details
|
|
|
|
04-05-2008
|
5.00
|
Pitot Tube, Wiring Runs, Gap Fairings
|
Details
|
|
|
|
03-12-2008
|
0.50
|
Bottom Wing Skins
|
Details
|
|
|
|
03-11-2008
|
2.10
|
Stall Warning System
|
Details
|
|
|
|
03-10-2008
|
1.50
|
Stall Warning System
|
Details
|
|
|
|
03-09-2008
|
2.00
|
Stall Warning Systems
|
Details
|
|
|
|
03-09-2008
|
0.40
|
Fuel Tanks
|
Details
|
|
|
|
03-08-2008
|
2.50
|
Fuel Tanks
|
Details
|
|
|
|
03-06-2008
|
0.50
|
Wing Ribs
|
Details
|
|
|
|
03-06-2008
|
0.50
|
Rear Spar
|
Details
|
|
|
|
03-06-2008
|
0.30
|
Outboard Leading Edge
|
Details
|
|
|
|
03-06-2008
|
0.50
|
Main Spar
|
Details
|
|
|
|
03-06-2008
|
0.50
|
Fuel Tanks
|
Details
|
|
|
|
02-02-2008
|
2.00
|
Horizontal Stabilizer Tip Fairings
|
Details
|
|
|
01-16-2008
|
1.00
|
Bottom Rudder Epoxy for Brass Inserts
|
Details
|
|
|
01-13-2008
|
2.00
|
Re Work Rudder Skins near Counterweight
|
Details
|
|
|
|
01-08-2008
|
3.00
|
Seat Floors and Tunnel covers
|
Details
|
|
|
01-05-2008
|
1.00
|
Laser Level Trim Tabs
|
Details
|
|
|
01-05-2008
|
0.50
|
Bottom Rudder Fairing Strobe
|
Details
|
|
|
|
12-22-2007
|
0.50
|
Bottom Rudder Fairing
|
Details
|
|
|
12-20-2007
|
1.00
|
Rudder Tip Fairing
|
Details
|
|
|
12-20-2007
|
0.50
|
Rudder Bottom Fairing
|
Details
|
|
|
|
12-03-2007
|
1.50
|
Elevator Tip Fairing
|
Details
|
|
|
11-19-2007
|
2.00
|
Trim System Re Installation
|
Details
|
|
|
|
11-19-2007
|
0.80
|
Elevator Tip Fairing
|
Details
|
|
|
|
11-17-2007
|
1.00
|
Trim System Problems
|
Details
|
|
|
|
11-16-2007
|
2.00
|
Install Trim System
|
Details
|
|
|
|
11-14-2007
|
0.75
|
Elevator Trim Cable Attach
|
Details
|
|
|
|
11-13-2007
|
2.00
|
Trim Servo Installation
|
Details
|
|
|
|
11-12-2007
|
0.50
|
Trim Bracket Assembly
|
Details
|
|
|
|
11-10-2007
|
2.70
|
Trim Bellcrank Assembly
|
Details
|
|
|
|
11-01-2007
|
1.50
|
Rudder attach and Travel
|
Details
|
|
|
10-31-2007
|
1.00
|
Adjusting Pushrod for correct angle/ Rudder bearin
|
Details
|
|
|
|
10-30-2007
|
0.70
|
Push Rod Assembly and Installation
|
Details
|
|
|
|
10-29-2007
|
1.70
|
Elevator Pushrod Assembly
|
Details
|
|
|
|
10-26-2007
|
0.30
|
Vertical Stabilizer Attach Front
|
Details
|
|
|
10-22-2007
|
0.80
|
Vertical Stabilizer Attach
|
Details
|
|
|
10-21-2007
|
3.00
|
Attaching Horizontal Stabilizer to Tail Cone
|
Details
|
|
|
10-20-2007
|
3.00
|
Riveting Aft Top Skin
|
Details
|
|
|
10-20-2007
|
2.90
|
Install Elevators
|
Details
|
|
|
|
10-18-2007
|
0.50
|
Horizontal Stabilizer Setup
|
Details
|
|
|
|
10-14-2007
|
2.00
|
Step 3, (10-22), Steps 1,2 (10-23)
|
Details
|
|
|
|
10-13-2007
|
1.00
|
Steps 1 & 2
|
Details
|
|
|
|
10-12-2007
|
1.00
|
Step 5
|
Details
|
|
|
10-08-2007
|
0.50
|
Rivet Skins to Longerons under aft deck
|
Details
|
|
|
|
10-07-2007
|
1.00
|
Rivet Bell crank Ribs
|
Details
|
|
|
10-06-2007
|
3.00
|
Rivet bottom skin to side skin
|
Details
|
|
|
10-04-2007
|
1.90
|
Left Bulkheads & Frames
|
Details
|
|
|
|
10-01-2007
|
0.70
|
Bulkheads and Frames
|
Details
|
|
|
|
09-30-2007
|
3.90
|
Rivet Stiffeners
|
Details
|
|
|
|
09-28-2007
|
1.00
|
Rivet Stiffeners
|
Details
|
|
|
|
09-27-2007
|
2.75
|
Rivet Stiffeners
|
Details
|
|
|
|
09-19-2007
|
0.50
|
Tailcone Final Assembly
|
Details
|
|
|
09-18-2007
|
0.75
|
Tailcone Final Assembly
|
Details
|
|
|
|
09-17-2007
|
1.00
|
Tailcone Final assembly
|
Details
|
|
|
|
09-15-2007
|
1.50
|
Riveting Bulkheads and Frames
|
Details
|
|
|
|
09-13-2007
|
3.50
|
Battery Channel and Bell Crank Assemblies
|
Details
|
|
|
|
09-11-2007
|
2.00
|
Finish Dimpling Skins, Frames etc.
|
Details
|
|
|
|
09-10-2007
|
1.50
|
Dimpling Skins
|
Details
|
|
|
|
09-09-2007
|
1.50
|
Dimpling and CS Skins Frames etc
|
Details
|
|
|
|
09-06-2007
|
1.75
|
Finish Deburring, Cut Tie Down Hole, Dimpling
|
Details
|
|
|
|
09-04-2007
|
0.75
|
Deburring
|
Details
|
|
|
|
09-03-2007
|
6.00
|
Deburring, Trim F1073R Skin
|
Details
|
|
|
|
08-31-2007
|
0.75
|
Deburring
|
Details
|
|
|
|
08-26-2007
|
1.50
|
Disassembly of Tailcone
|
Details
|
|
|
|
08-25-2007
|
1.00
|
Shoulder Harness Anchors, Cover Plate
|
Details
|
|
|
08-24-2007
|
1.00
|
Drilling Aft Deck Areas
|
Details
|
|
|
08-23-2007
|
0.50
|
Drilling Aft Deck
|
Details
|
|
|
|
08-22-2007
|
0.75
|
Up Elevator Stop
|
Details
|
|
|
|
08-21-2007
|
1.75
|
Drilling Topm Skins and Stiffeners
|
Details
|
|
|
08-20-2007
|
0.75
|
Attaching Top Skins
|
Details
|
|
|
|
08-18-2007
|
4.00
|
Drilling Longerons, Frames and Bulkheads
|
Details
|
|
|
|
08-17-2007
|
1.50
|
Bulkhead Channel, Bell Crank Rib and Rib Angles
|
Details
|
|
|
|
08-14-2007
|
1.00
|
Rudder Stop Brace, 1006 Bulkhead
|
Details
|
|
|
|
08-13-2007
|
1.50
|
Cleco Skins and Bulkheads
|
Details
|
|
|
|
08-12-2007
|
4.00
|
Cleco Skins and Stiffeners
|
Details
|
|
|
|
08-11-2007
|
5.00
|
Clecoing Frames, Bulkheads, Ribs and Skins
|
Details
|
|
|
|
08-09-2007
|
0.50
|
Bending Longerons
|
Details
|
|
|
|
08-08-2007
|
2.00
|
Mark Stiffeners, Longerons
|
Details
|
|
|
|
08-07-2007
|
0.50
|
Removed vinyl from Stiffeners
|
Details
|
|
|
|
08-06-2007
|
2.00
|
Assemble Frames and Cut Stiffeners
|
Details
|
|
|
|
08-05-2007
|
1.00
|
Assemble1007 Frame
|
Details
|
|
|
|
08-04-2007
|
5.50
|
Preparing and manufacturing Parts
|
Details
|
|
|
|
08-03-2007
|
0.30
|
Tie Down Bar
|
Details
|
|
|
|
07-28-2007
|
2.00
|
Finish Elevator
|
Details
|
|
|
07-27-2007
|
2.50
|
Trim Tab Hinges
|
Details
|
|
|
|
07-19-2007
|
2.50
|
Riveting Trim Tab
|
Details
|
|
|
|
07-16-2007
|
1.75
|
Trim Tab Disassembly and Dimpling
|
Details
|
|
|
|
07-15-2007
|
1.00
|
Trim Tab Horns
|
Details
|
|
|
|
07-14-2007
|
3.25
|
Drilling and Bending Skins
|
Details
|
|
|
|
07-13-2007
|
1.00
|
Trim Cable Brackets and Counter weights
|
Details
|
|
|
|
06-24-2007
|
2.00
|
Roll Leading Edges
|
Details
|
|
|
|
06-23-2007
|
2.00
|
Rivet Trailing Edge and Skins
|
Details
|
|
|
|
06-21-2007
|
1.00
|
Trailing Edge Bend
|
Details
|
|
|
|
06-19-2007
|
1.50
|
Trim Tab Clamp Blocks
|
Details
|
|
|
|
06-18-2007
|
1.20
|
Seal Trailing Edges
|
Details
|
|
|
|
06-17-2007
|
5.00
|
Riveting, Riveting, Riveting
|
Details
|
|
|
|
06-16-2007
|
2.20
|
Riveting parts to Elevator Skins
|
Details
|
|
|
|
06-13-2007
|
1.50
|
Rivet Rear Spars to Rib Halves
|
Details
|
|
|
|
06-12-2007
|
3.00
|
Riveting
|
Details
|
|
|
|
06-11-2007
|
3.50
|
Dimpling, Countersinking Ribs and Spars
|
Details
|
|
|
|
06-10-2007
|
4.10
|
Finish Deburring/ Dimpling
|
Details
|
|
|
|
06-02-2007
|
3.00
|
Disassembly and Debur
|
Details
|
|
|
|
06-01-2007
|
17.00
|
Dimple Cover Plates and Reinforcement Plates
|
Details
|
|
|
|
05-30-2007
|
0.75
|
Trim Anchor Brackets
|
Details
|
|
|
|
05-24-2007
|
1.50
|
Final Drill Trailing Edge
|
Details
|
|
|
05-23-2007
|
2.30
|
Final Drilling Elevator Structures
|
Details
|
|
|
|
05-21-2007
|
1.50
|
Top Skin and Trailing Edge
|
Details
|
|
|
|
05-19-2007
|
2.00
|
Drilling Elevator Gussets
|
Details
|
|
|
|
05-16-2007
|
0.75
|
Trim Access Plates
|
Details
|
|
|
|
05-14-2007
|
2.00
|
Cleco Rear Spars to Ribs and Bottom Skin
|
Details
|
|
|
|
05-11-2007
|
1.50
|
Cleco Front Spar to Bottom Skin
|
Details
|
|
|
|
05-10-2007
|
1.30
|
Elevator Closeout Tabs
|
Details
|
|
|
|
05-07-2007
|
1.00
|
prepare ribs for final drilling
|
Details
|
|
|
|
05-05-2007
|
2.25
|
deburring ribs
|
Details
|
|
|
|
04-30-2007
|
1.50
|
preparing parts
|
Details
|
|
|
|
04-23-2007
|
1.80
|
riveting rear spar assembly
|
Details
|
|
|
04-22-2007
|
4.00
|
Finishing riveting
|
Details
|
|
|
04-20-2007
|
3.00
|
Rivet skins to inspar ribs
|
Details
|
|
|
04-16-2007
|
2.00
|
Rivet Skins
|
Details
|
|
|
|
04-14-2007
|
1.00
|
Last 2 Inspar Ribs Riveted.
|
Details
|
|
|
|
04-12-2007
|
1.00
|
Front Spar/ Rib Assembly
|
Details
|
|
|
|
04-11-2007
|
2.00
|
Nose Rib Assembly
|
Details
|
|
|
|
04-10-2007
|
2.50
|
Riveting the Inspar Ribs to the Front Spar
|
Details
|
|
|
|
04-09-2007
|
1.00
|
Rivet Inspar Ribs to Stringers
|
Details
|
|
|
|
04-09-2007
|
2.00
|
Countersinking Front and Rear Spar Flanges.
|
Details
|
|
|
|
04-08-2007
|
1.00
|
Dimpling
|
Details
|
|
|
|
04-04-2007
|
1.00
|
Dimpling
|
Details
|
|
|
|
04-03-2007
|
2.00
|
Dimpling HS
|
Details
|
|
|
|
04-01-2007
|
4.00
|
Deburring HS assembly
|
Details
|
|
|
|
03-31-2007
|
2.00
|
Final drilling Horizontal Stabilizer assembly.
|
Details
|
|
|
03-16-2007
|
3.00
|
Stringer Assembly and Rear Spar
|
Details
|
|
|
|
03-12-2007
|
1.50
|
Nose Ribs to Skins
|
Details
|
|
|
|
03-11-2007
|
6.00
|
Preparing Inspar Ribs and Nose Ribs
|
Details
|
|
|
|
03-09-2007
|
2.00
|
Riveting Front Spar Doubler and Trimming Ribs
|
Details
|
|
|
|
03-08-2007
|
4.00
|
Front Spar and Doubler
|
Details
|
|
|
|
03-07-2007
|
2.50
|
Front Spar Caps and Stringers
|
Details
|
|
|
|
03-05-2007
|
2.50
|
Front Spar Attachment Brackets
|
Details
|
|
|
|
03-04-2007
|
4.30
|
Rear Spar Assembly
|
Details
|
|
|
|
02-13-2007
|
2.00
|
Rolling leading Edges
|
Details
|
|
|
|
02-13-2007
|
1.50
|
Finished Rudder
|
Details
|
|
|
02-10-2007
|
1.50
|
Rolling Leading edge
|
Details
|
|
|
02-08-2007
|
3.00
|
Riveting/ Back Rivet Trailing Edge
|
Details
|
|
|
02-06-2007
|
0.50
|
Riveting
|
Details
|
|
|
|
02-05-2007
|
1.00
|
Hole Cleaning
|
Details
|
|
|
|
02-03-2007
|
2.00
|
Riveting and Sealant
|
Details
|
|
|
|
02-02-2007
|
3.00
|
Riveting
|
Details
|
|
|
|
01-28-2007
|
4.50
|
Rudder Dimpling
|
Details
|
|
|
|
01-27-2007
|
1.00
|
Counter Sink and Riveting
|
Details
|
|
|
|
01-23-2007
|
3.50
|
Rudder Skin Attachment
|
Details
|
|
|
|
01-20-2007
|
2.50
|
Begin Rudder Assembly
|
Details
|
|
|
|
01-19-2007
|
2.00
|
Rudder Parts Prep
|
Details
|
|
|
|
01-16-2007
|
1.00
|
Finished Vertical Stabilizer.
|
Details
|
|
|
01-15-2007
|
2.00
|
Riveting skin
|
Details
|
|
|
|
01-07-2007
|
4.50
|
Begin Riveting VS
|
Details
|
|
|
|
01-06-2007
|
3.50
|
Dimpling and Countersinking
|
Details
|
|
|
|
01-04-2007
|
1.00
|
Dimpling Skin
|
Details
|
|
|
|
01-03-2007
|
0.50
|
prepare skin for dimpling
|
Details
|
|
|
|
12-31-2006
|
2.50
|
attaching skins
|
Details
|
|
|
12-30-2006
|
4.50
|
Vertical Stabilizer Skeleton
|
Details
|
|
|
|
12-29-2006
|
0.50
|
Flange Holes of Rear Spar
|
Details
|
|
|
|
12-28-2006
|
0.50
|
Spar Caps to Rear Spar
|
Details
|
|
|
|
12-27-2006
|
0.50
|
Spar Caps
|
Details
|
|
|
|
12-16-2006
|
3.00
|
Inventory of Empennage Parts
|
Details
|
|
|
