Powered By Kitlog Pro v2.0
KENNETH T.'S WEB SITE
RV-7A
Wings
Work Logs Found:
90
Category Work Time:
397 Hours
Date
Hours
Work Log Summary
Details
07-25-2013
5.00
Installed wingtips.
Details
07-24-2013
6.00
Aligned the ailerons.
Details
07-23-2013
5.00
Flap rod adjustments.
Details
07-22-2013
4.00
Wing work.
Details
07-17-2013
6.00
Both wings on.
Details
07-16-2013
5.50
Installed the left wing.
Details
05-21-2012
12.00
Finished right wing and stored in cradle.
Details
05-16-2012
2.00
Cut and flared fuel tube for left wing.
Details
05-15-2012
5.00
Installed nutplates on wing for the fairing.
Details
05-14-2012
5.50
Installed wing root fairing then removed.
Details
05-11-2012
4.00
Fabricated fuel tank vent tube.
Details
05-07-2012
4.00
Flap actuating rod installed.
Details
05-03-2012
4.00
Fuel tank attach bracket installed.
Details
05-01-2012
7.00
Installed right wing and drilled aft spars.
Details
04-26-2012
4.00
Left wing moved to garage & installed.
Details
04-19-2012
3.00
Fabricated drill guides of drilling rear spars.
Details
04-16-2012
3.50
Drilled out QB wing rivets on inboard rib.
Details
04-09-2012
4.00
Practiced driving drift pins into carrythru spar.
Details
04-06-2012
4.00
Trimmed wing rear spars.
Details
04-04-2012
4.00
Repositioned fuselage for wing attachment.
Details
03-15-2012
4.00
Rewired Aveo 6-in-1 lights.
Details
03-14-2012
6.00
Reinstalled Aveo 6-in-1 wingtip light modules.
Details
02-15-2012
2.00
Functional test of Aveo 6-in-1 lights.
Details
02-14-2012
2.00
Connected wire bundles to terminal blocks.
Details
02-13-2012
4.00
Made wire bundles for attaching to lights.
Details
02-12-2012
4.00
Wing wires attached to terminal blocks.
Details
02-11-2012
4.00
Started wiring wingtip lights.
Details
02-08-2012
3.50
Fabricated right wingtip cutout lens.
Details
02-07-2012
4.50
Cut wingtip lenses and fabbed the left tip lens.
Details
02-06-2012
3.00
Shimed the foam rib on right wingtip.
Details
02-03-2012
4.00
Cut out foam wingtip ribs and glued.
Details
02-02-2012
5.50
Flap hinge loops cutout for pins insertion.
Details
02-01-2012
6.00
Started designing a foam rib to strengthen fibergl
Details
01-29-2012
3.00
Finished installing nutplates on wingtips.
Details
01-26-2012
4.00
Fabbed laning/taxi/strobe light reflector.
Details
01-25-2012
5.00
Riveted nutplates and dimpled wing skins.
Details
01-23-2012
4.00
Drilled nutplate holes onto wingtips.
Details
01-22-2012
4.00
Matchdrilled strip and wingtip end tip.
Details
01-21-2012
5.00
Added reinforcing srtips to wingtips.
Details
01-19-2012
4.50
Cut left wingtip to aileron gap and matchdrilled.
Details
01-18-2012
4.00
Marked left wingtip for aileron gap.
Details
01-17-2012
4.00
Prepping wingtip for installation
Details
01-15-2012
9.00
Finished riveting last skin on the right wing.
Details
01-12-2012
4.50
Finished riveting left wing and installed pitot.
Details
01-11-2012
4.00
More riveting.
Details
01-10-2012
5.00
More left wing skin riveting.
Details
01-09-2012
3.00
Started riveting last skin on left wing.
Details
01-08-2012
3.00
Redoing pitot heat wiring and tubing.
Details
01-05-2012
6.00
Fabricated "aileron stop" bushings.
Details
01-03-2012
4.00
Removed aluminum aileron stops.
Details
11-30-2011
4.00
Added wiring conduit clamps
Details
11-27-2011
1.00
Moved wings into garage.
Details
11-17-2011
3.50
Moved left wing to deck and wired the right wing.
Details
11-16-2011
2.00
Scarf joint problem solved.
Details
11-14-2011
4.50
Added nutplates to wing skin access hole.
Details
11-12-2011
4.00
Continuity check of wiring & pitot ops check.
Details
11-11-2011
4.00
Added wingtip lighting wires.
Details
11-08-2011
6.00
Pitot installation continued.
Details
11-04-2011
4.00
Secured PVC wiring conduit in the wings.
Details
11-02-2011
4.00
Started Dynon pitot/heat installation.
Details
07-05-2011
3.00
Resealed right wing tank.
Details
10-29-2008
5.00
Installed Dynon AP servo in right wing.
Details
10-25-2008
3.00
Started installing pitot line in left wing.
Details
05-29-2008
4.00
Installed fuel pickup tubes & quantity sensors.
Details
05-03-2008
3.00
Prepared Fuel Sensors for Wing Fuel Tanks.
Details
04-23-2008
3.00
Mounted Dynon Pitot Heater Control Box
Details
04-15-2008
3.00
Drilled and tapped Dynon pitot.
Details
04-14-2008
4.50
Cut streamline pitot hole, deburred, dimpled, prim
Details
04-13-2008
6.00
Riveted bracket & preped pitot mounting plates.
Details
04-12-2008
2.00
Dimpled Lower Wing Spars, Ribs, and Skins
Details
04-11-2008
5.00
Back Drilled Lower Outboard Right Wing Skin
Details
04-10-2008
5.00
Prep to Install Dynon Heated AOA Pitot
Details
09-10-2007
3.00
Charlotte and I riveted the aileron gap fairings.
Details
09-07-2007
6.50
Prepped and riveted left flap brace and hinge.
Details
09-04-2007
6.00
Prepped and riveted right flap brace & hinge.
Details
09-03-2007
6.50
Riveted outboard aileron hinge brackets.
Details
09-01-2007
4.50
Attached aileron hardware & drilled oversize holes
Details
08-31-2007
2.50
Drilled aileron attach hardware.
Details
08-28-2007
6.50
Set inbd. aileron brackets and prepped flap brace.
Details
08-27-2007
5.00
Drilled the aileron hinge brackets to rear spar.
Details
08-25-2007
6.00
Riveted and primed aileron push rods.
Details
08-24-2007
6.50
Drilled Aileron pushrod and rod ends.
Details
08-14-2007
3.50
Finished drilling wing wiring holes and cut ailero
Details
08-11-2007
4.00
Installed aileron bellcranks onto QB wings.
Details
08-10-2007
3.00
Drilled wiring conduit holes on the right wing.
Details
08-09-2007
6.00
Started drilling wing wiring conduit holes in the
Details
08-08-2007
4.00
Drilled out and reriveted 3 rivet in aileron hinge
Details
08-07-2007
6.00
Assembled the aileron hinges.
Details
07-23-2007
4.00
Inventoried parts for QB wings and fuselage.
Details
06-15-2007
4.00
Started constructing Wing Cradle while waiting for
Details
SITE NAVIGATION
Contact Builder
RV-7A Home
Category
# Logs
# Hours
All
720
3309
Avionics
40
188
Cowling
11
54
Electrical System
113
524
Empennage
68
306
Engine
50
228
Fuselage
195
867
Instrument Panel
33
164
Miscellaneous
120
581
Wings
90
397
Copyright © 2001-2024 Matronics. All Rights Reserved.
