Powered By Kitlog Pro v2.0
John (Jack) Clark's Web Site
RV-8A
Avionics
195 Logs Found
Date
Hours
Work Log Summary
Details
02-02-2013
0.3
Secured the GPS Antennae
Details
01-29-2013
4.0
Configured GRT EFISs for ADS-B
Details
01-28-2013
1.0
Called NavWorx
Details
01-27-2013
2.0
NavWorx ADS-B Configuration
Details
01-06-2013
1.0
Garmin GPS 18x is Working Great
Details
01-05-2013
3.0
Installed VoiceFlight USB Update Port
Details
12-21-2012
1.0
Added Power Switch for the VoiceFlight
Details
12-19-2012
1.0
Installed the VoiceFlight Voice Activation Switch
Details
09-12-2012
4.0
Troubleshot the Com Problems
Details
09-10-2012
3.0
Rewired the Grounds of the Copilot Stick Grip
Details
09-08-2012
1.0
Trimmed GPS Antennae Shims and Installed
Details
09-08-2012
1.0
Tested the Intercom and the Radios First Time
Details
09-07-2012
1.5
Re-fabricated the GPS Antennae Shims
Details
09-06-2012
1.5
Formed a Shim for the GPS Antennae
Details
09-05-2012
0.8
Drilled Holes in Aft Top Skin for the GPS Antennae
Details
09-03-2012
1.5
Wired the VoiceFlight Wires to the Pilot's Com Jac
Details
08-31-2012
3.0
Wired the VoiceFlight Box
Details
08-31-2012
0.5
Adjusted the Installation of the Avionics Post Gro
Details
08-17-2012
1.0
Attached VoiceFlight Box to Forward Avionics Bulkh
Details
08-14-2012
2.0
Fabricated and Installed Rear Stick Connector Moun
Details
06-18-2012
1.5
Changed GRT EFIS Tiny 4-40 Screws to Large Ones
Details
06-16-2012
0.0
Worked to Organize Left Side of Avionics Bay 2
Details
06-16-2012
2.0
Worked to Organize Left Side of Avionics Bay 1
Details
05-24-2012
0.5
Stuck Pitot and AoA Tubes Through Lt Fuselage
Details
05-16-2012
0.5
Ran The VOR Coax Throught the Rt Fuselage Wall
Details
05-15-2012
1.0
Installed the Two Communication Antennae
Details
05-10-2012
1.0
Wired the IBBS Info Light
Details
05-08-2012
1.0
Installed a IBBS LED Indicator Light in the Panel
Details
05-07-2012
1.0
Re-Installed TCW IBBS
Details
04-15-2012
0.5
Removed IBBS for shipping
Details
04-15-2012
2.0
Found Out the GRT HX Can't Read IBBS Voltages
Details
04-12-2012
1.0
Installed the TCW IBBS Master Cutoff Switch
Details
04-11-2012
0.5
Corrected Fuel Totalizer Wiring on #1 Injector
Details
03-21-2012
1.0
Sent the ADS-B Back for Hardware and Software
Details
03-20-2012
2.0
The VP Serial 7 Input to the GRT EFISs Missing
Details
03-20-2012
0.5
Removed the ADS-B for Return for Upgrade
Details
03-19-2012
1.0
Return to Troubleshoot Missing ELT GPS Signal
Details
03-18-2012
3.0
Checked ELT GPS Signal without success
Details
03-17-2012
2.0
Unable to configure the ADS-B
Details
03-15-2012
3.0
Configured the GRT HX Displays and the VP System
Details
03-14-2012
2.0
Investigated Absence of Fuel Totalizer Value on EI
Details
03-10-2012
3.0
Configured the EIS and GRT HX EFIS Displays
Details
03-03-2012
0.0
Unstalled Panel USB Plugs
03-03-2012
3.0
Installed 3 USB Plugs in the Instrument Panel
Details
09-20-2011
1.0
Attached TNC Connector For G430W GPS
Details
09-18-2011
7.0
Fixed the G-430W Backup Power Problem
Details
09-17-2011
6.0
Tested EFISs OK. Checked Backup Power System
Details
09-15-2011
3.0
Finished EFIS/AHRSs CPC Connectors Installation
Details
09-14-2011
2.5
Re-wired the EFISs and AHRSs Secondary Power
Details
09-12-2011
4.0
Finished Avionics Installation and Power Up
Details
09-11-2011
2.5
Re-installed Avionics in Panel and Secured Wires
Details
09-07-2011
1.0
Wired the ADS-B Fault Light
Details
09-06-2011
0.8
Installed AHRSs and Pitot/Static Connections
Details
09-06-2011
0.3
Adel Secures Gretz and VP Cables
Details
09-01-2011
0.5
Connected G430W GPS Antenna to Rack
Details
09-01-2011
1.5
Connected Fuel Guardian and Autopilot Wires
Details
08-28-2011
0.5
Primed the AHRS Mount
Details
08-28-2011
1.0
Installed the ADS-B Fault Light in the Panel
Details
08-28-2011
0.5
Installed Rivnuts to Attach the AHRS Mount
Details
08-27-2011
1.5
Clecoed the Forward Top Skin in place
Details
08-26-2011
2.5
Connected Antennae to the Avionics
Details
08-25-2011
1.5
Fabricated a Mount of the VOR Antenna Splitter
Details
08-20-2011
2.0
Ran EIS Out Wire from EFIS towards the EIS
Details
08-20-2011
0.5
Connected TCW IBBS Info wire to the GRT EFIS
Details
08-15-2011
2.5
Finished Pitot/Static Installation To the EIS
Details
08-14-2011
6.0
Wired the Autopilot Terminal
Details
08-12-2011
2.0
Wired Gretz Heated Pitot Tube Output to VP Sys.
Details
08-11-2011
1.0
Mounted Gretz to VP Conversion Circuit Board
Details
08-08-2011
2.0
Connected ELT Power, Ground and Shield
Details
08-06-2011
2.5
Straightened/Organized more wiring
Details
08-06-2011
1.0
Reversed the Antenna Pigtail Direction
Details
08-06-2011
1.0
Connected the AFS AoA to the Pitot/Static System
Details
08-06-2011
0.0
Connected GPS Serial Output to the ELT - Cont.
Details
08-06-2011
2.0
Connected GPS Serial Output to the ELT
Details
08-05-2011
5.0
Worked on several tasks that need to be done.
Details
08-05-2011
3.0
Wired the EIS System
Details
07-12-2011
2.0
Soldered the Mini DIN Connector for GPS to ELT
Details
07-12-2011
0.0
Soldered the Mini DIN Connector for GPS to ELT
Details
07-12-2011
1.0
Laced the ELT Related Wires
Details
07-10-2011
1.0
Installed the ELT Antenna
Details
07-09-2011
3.0
Cut the Panel for the ELT Remote Panel Control
Details
07-08-2011
1.0
Ran the ELT Cables Forward Along Right Side
Details
07-07-2011
1.0
Flipped the ELT Securing Bands
Details
07-06-2011
3.0
Replaced the ELT Mounting Plate
Details
06-25-2011
1.5
Riveted the EIS Tray to the Forward Right Panel
Details
06-24-2011
0.5
Top Coated the EIS Tray Dawn Patrol Grey
Details
06-23-2011
2.0
Primed EIS Tray After Drilling to Right FWD Panel
Details
06-15-2011
1.5
Modified the EIS Tray
Details
06-14-2011
2.5
Fabricated the EIS Tray
Details
06-04-2011
1.0
Installed Mic and Headphone Jacks
Details
06-02-2011
2.5
Soldered Wires to the Mike and Headset Plugins
Details
05-30-2011
1.5
Wired the Tank Sensors for the Fuel Guardian
Details
05-28-2011
2.0
Ran Pitot/Static Lines to the AHRS
Details
05-28-2011
6.0
Organized Wires on the Left Side of the Panel
Details
05-28-2011
0.0
Organized Wires
Details
05-26-2011
1.0
Ran the Magnetometer Wires Through the Panel
Details
05-26-2011
2.0
Ran Backup Power Wires to the AHRSs
Details
05-25-2011
1.5
Organized Panel Wires
Details
05-24-2011
1.5
Put the Avionics Trays Back on the Panel
Details
05-24-2011
1.5
Laced More Wires Behind the Panel
Details
05-22-2011
1.5
Painted the Panels Rustoleum Graphite Gray
Details
05-22-2011
4.0
Organized Avionics Wires Behind the Panel
Details
05-22-2011
1.0
Cut Panel Holes for the Air Vents
Details
05-21-2011
1.0
Prepared to Cut Panel Holes for the Air Vents
Details
05-19-2011
8.0
Still Organizing Avionics Wires
Details
05-15-2011
8.0
Installed and Wired the TCW IBBS
Details
05-14-2011
6.5
Organizing Panel Wires
Details
05-10-2011
6.0
Organized Panel Wires
Details
05-10-2011
0.0
Organized Panel Wires
Details
05-09-2011
1.5
Worked on Organizing Avionics Wiring on Right Side
Details
05-09-2011
1.5
Soldered the SL-40 Antenna Pigtail in Place
Details
05-09-2011
0.0
Soldered the SL-40 Antenna Pigtail in Place
Details
05-06-2011
2.5
Soldered 10K Ohm Resistors in Keep Alive Wires
Details
05-06-2011
2.5
Removed the Instrument Panel Equipment
Details
04-02-2011
6.0
Receiving Fault Message on the Backup B Panel
Details
04-01-2011
2.0
Programming G430W and GRT EFISs
Details
03-27-2011
1.5
Programmed the GRT EFISs until Battery Died
Details
03-23-2011
1.5
Programming the VP-200
Details
03-22-2011
1.5
Installed an Inline Fuse for the Fuel Guardian Lig
Details
03-20-2011
1.0
Wired Inline Fuse Holders for the Fuel Guardian
Details
03-19-2011
1.5
Ran the Pitot/Static Lines for the Avionics and Ao
Details
03-16-2011
1.0
Corrected Light Wiring of Fuel Guardian
Details
03-14-2011
1.0
Farmiliarized Myself with Programming the VP-200
Details
03-12-2011
1.0
Updated the GRT EFISs Nav Data
Details
03-11-2011
2.0
Found the Cause of the AHRSs Failures
Details
03-10-2011
2.5
Started testing elctrical circuits
Details
03-04-2011
8.0
Installed the AHRSs Mounting Platform
Details
03-02-2011
1.0
Made Left Side of the AHRS Mount
Details
02-28-2011
1.5
Ran Five 20ga. Wires from the Hub to the Firewall
Details
02-27-2011
2.0
Wired the Grounding Hub
Details
02-27-2011
3.0
Installed and Wired the Panel Grounding Hub
Details
02-26-2011
3.0
Wired GNS 430W to the Avionics Power Terminal
Details
02-26-2011
1.0
Mounted the Fuel Guardian
Details
02-20-2011
2.0
Wired the AFS Sport Angle of Attack Indicator
Details
02-20-2011
4.0
Wired Power for Avionics to the Terminal
Details
02-20-2011
0.5
Started to Run Mic and Headphone Wires
Details
02-20-2011
1.0
Soldered Wires to AoA Test and Dimmer Buttons
Details
02-14-2011
2.0
Wired Power Side of the Lighting Terminal
Details
02-13-2011
3.0
Wired the Bottom Row of Avionics Power Terminal
Details
02-12-2011
8.0
Worked on Wiring the Left Side of the Panel
Details
02-11-2011
1.5
Attached TCW IBBS to the Baggage Bulkhead
Details
02-08-2011
1.0
Installed the Instrument Panel in the Aircraft
Details
02-06-2011
2.0
Switched Front Stick Grip Direction on the Stick
Details
02-06-2011
1.0
Installed Connector on Rear Stick Fuselage Cable
Details
02-06-2011
2.5
Corrected the Wiring of the Grips PTT Switches
Details
02-06-2011
1.5
Attached D-sub Connector on Rear Stick Cable
Details
02-04-2011
2.5
Trimmed the F-803B L&R to Clear Installed Avionics
Details
02-03-2011
4.0
Installed Avionics in the Panel
Details
02-03-2011
2.0
Attached Cables to the Aft End of Avionics Trays
Details
02-02-2011
0.3
Drilled Holes for the AoA Button Switches
Details
01-29-2011
2.0
Cut the Opening for the Advanced Flight AoA
Details
01-28-2011
3.0
Cut the Panel Opening for the Bottom EFIS
Details
01-27-2011
3.0
Cut the Upper GRT HX Opening in the Panel
Details
01-24-2011
1.0
Put D-sub Connector on the Front Stick Cable
Details
01-24-2011
1.0
Installed the Rear Stick Grip on the Stick
Details
01-23-2011
2.0
Installed the Grips Back on the Sticks
Details
01-18-2011
1.0
Re-Riveted Antennae Doublers to Fuselage
Details
01-17-2011
3.0
Removed all of the Antennae Doubler Installations
Details
01-12-2011
5.0
Installed the Fuel Guardian Lights in the Panel
Details
01-10-2011
2.0
Mounted a Flaps Microswitch for the Advanced AoA
Details
01-08-2011
3.0
Cut Mounting Holes for the TruTrak Turn and Bank
Details
01-06-2011
2.0
Match Drilled the Avionics Mounting Rail To Panel
Details
01-04-2011
2.5
Attached the Avionics Mounting Rail to Avionics
Details
12-31-2010
0.5
Put BNC Connector on the Transponder Cable
Details
12-31-2010
1.0
Made Hangers for the ADS-B GPS Antenna Cable
Details
12-28-2010
8.0
Cut the Holes for the Vertical Power Display Unit
Details
12-27-2010
1.5
Drew Verical Power Display Unit Opening
Details
12-26-2010
2.5
Made 16 Nuts for the Avionics Mounting Rail
Details
12-26-2010
0.5
Duct Taped the Avionics Trays Together
Details
12-26-2010
3.0
Cut the Avionics Stack Opening in the Panel
Details
12-20-2010
1.5
Drew GRT EFIS Positions on the Panel
12-18-2010
2.0
Instrument Panel Planning and Photos
Details
12-18-2010
0.0
Instrument Panel Planning and Photos
12-16-2010
1.0
Ran the ADS-B GPS Cable
Details
12-15-2010
2.5
Installed the ADS-B cable 37 pin D-Sub Connector
Details
12-12-2010
0.3
Installed the Transponder Antenna
Details
12-12-2010
1.0
Installed the ADS-B UAT Antenna and Cable
Details
12-08-2010
1.0
Put Shells on the Magnetometer D-Dub Connectors
Details
12-06-2010
1.0
Routed the Magnetometer Bundles
Details
12-05-2010
2.0
Laced the Remaining Magnetometer Wiring Bundle
Details
12-04-2010
2.5
Laced One of the Magnetometer Wire Bundles
Details
11-21-2010
4.0
Fabricated the Transponder Antenna Doubler Plate
Details
11-20-2010
1.0
Attached the FastStack Pro-X Hub to Panel
Details
11-19-2010
3.0
Fabricated Doubler Plates for the Commo Antennae
Details
11-17-2010
1.0
Drilled and Dimpled the ADS-B Antenna Doubler
Details
11-16-2010
1.5
Fabricated the ADS-S Antenna Doubler
Details
11-12-2010
2.0
Installed the Dual Magnetometers
Details
11-10-2010
0.5
Drilled Mounting Holes in the Magnetometers
Details
11-10-2010
0.5
Drew a Template for the Magnetometer Installation
Details
11-07-2010
2.0
Ran the RG-400 Cables for the Antennae
Details
11-07-2010
0.5
Ran Fuel Level Cables from the Panel Area
Details
11-02-2010
3.0
Ran Autopilot Servo Wires
Details
10-27-2010
1.5
Mounted the ADS-B to the Mounting Panel
Details
10-26-2010
2.5
Finished the ADS-B Mount
Details
10-25-2010
3.0
Started Fabrication of NavWorx ADS-B Mount
Details
SITE NAVIGATION
Contact Builder
RV-8A Home
All
Avionics
Brakes
Canopy
Cooling System
Cowling
Electrical System
Empennage
Engine
Fiberglass
Finishing Kit
Flight Control Syste
Forward Baggage Comp
Forward Top Skin
Fuel System
Fuselage
Heating System
Interior
Landing Gear
Lighting
Miscellaneous
None
Oxygen System
Painiting
Painting
Prop
Sensors
Ventilation
Windscreen
Wings
Copyright © 2001-2013 Matronics. All Rights Reserved.
