KitLog pro

Powered By Kitlog Pro v2.0

Greg's RV-12 N719VA (reserved)
Work Logs Found: 36
Category Work Time: 77 Hours
 Date
Hours
Work Log Summary

Details

 04-06-2021
1.25
shorten the avionics dimmer pot shaft
Details

 09-13-2020
2.00
build the ELT GPS received test tool
Details
     

 09-11-2020
2.50
Install ELT remote nameplate, wire connector
Details
       

 09-10-2020
1.00
Investigate the ELT wiring
Details

 09-05-2020
2.00
Finish AP cutoff wiring, connect trim tab wiring
Details
       

 09-01-2020
1.50
install remote ELT
Details
       

 08-31-2020
2.50
clean-up the wiring behind the instrument panel
Details
       

 08-30-2020
4.50
misc avionics wiring and install
Details
       

 08-29-2020
3.75
Many items related to the avionics installation
Details
       

 08-28-2020
3.00
wire up the CO monitor wires to EMS connector
Details
     

 08-27-2020
1.00
mount the CO monitor module
Details
     

 08-26-2020
4.00
wire up GPS, install connector on CO monitor
Details
       

 08-25-2020
3.00
review CO monitor installation
Details

 08-24-2020
1.00
Review elec. schematics and connector changes
Details

 08-23-2020
0.25
tighten transponder antenna & connect cable
Details

 08-22-2020
2.75
finish countersink holes in instr. panels, rivnuts
Details

 08-19-2020
2.25
file and fit cutouts for AP Knob Panels
Details
       

 08-18-2020
2.75
cutout the holes for AP Knob Panles
Details
     

 08-17-2020
2.50
prep comm brackets and ADS-b brackets
Details
     

 08-15-2020
2.40
mount ELT antenna bracket, install stack angles
Details
       

 08-13-2020
3.00

Details
     

 08-12-2020
1.50
install xponder mount and xponder, connect ant.
Details
     

 08-11-2020
1.00
rivet rivnuts for starter module, prep xponder mou
Details
     

 08-10-2020
1.75
countersink Skyview panel and rivet doubler
Details

 08-08-2020
1.00
install EMS and Battery modules
Details
     

 08-07-2020
1.50
install ransponder antenna, ELT parts
Details
     

 08-06-2020
4.50
protect ADS-B antenna, deburr parts
Details
       

 08-05-2020
1.75
install ADS-B antenna
Details
       

 08-04-2020
3.50
prime rivnuts, install d-sub ADAHRS, install ADAHR
Details
       

 07-29-2020
1.75
fixed 2 cotter pins, misc. install 2 rear baggage
Details
       

 07-28-2020
1.50
received and inventoried Dynon Avionics
Details

 06-15-2020
2.50
install pitch servo, drill hole for AP stop switch
Details
       

 06-14-2020
0.30
attach pitch pushrod to servo
Details

 06-13-2020
3.25
Install roll servo
Details
       

 06-11-2020
2.00
make autopilot servo push rods
Details
     

 05-31-2020
0.50
ordered Dynon Autopilot servos
Details










Copyright © 2001-2021 Matronics. All Rights Reserved.