Date
|
Hours
|
Work Log Summary
|
Details
|
07-16-2018
|
2.00
|
Fuel Flow and Unusable Fuel Testing
|
Details
|
|
|
05-31-2018
|
3.00
|
Installed cowliing, adjusted skybolts and installe
|
Details
|
|
|
05-23-2018
|
0.50
|
Installed baffle strips and cleaned up anti-chafe
|
Details
|
|
|
|
05-22-2018
|
3.50
|
Adjust heat muff, installed spark plugs, wet sande
|
Details
|
|
|
05-17-2018
|
0.50
|
Added additional adel clamp on heater SCEET and di
|
Details
|
|
|
|
05-16-2018
|
1.00
|
More cowling wet sanding
|
Details
|
|
|
|
05-15-2018
|
3.00
|
Skybolt cowl fasteners drilled and riveted to FW p
|
Details
|
|
|
05-12-2018
|
7.00
|
Nutplates installed on cowling, primed cowl, spinn
|
Details
|
|
|
|
04-28-2018
|
6.00
|
Cowl inlet baffle seals fabricated, clips fabricat
|
Details
|
|
|
04-27-2018
|
2.50
|
Engine is done! CHT/EGT lines for all cyls. SCEE
|
Details
|
|
|
04-26-2018
|
5.00
|
Baffling and engine install almost complete.
|
Details
|
|
|
04-24-2018
|
2.00
|
Primed/painted and riveted 4130 doublers to cyl ba
|
Details
|
|
|
04-23-2018
|
1.50
|
Fabricated and drilled 4130 reinforcements for low
|
Details
|
|
|
|
04-22-2018
|
8.00
|
Baffle seals fabricated and installed
|
Details
|
|
|
04-21-2018
|
3.00
|
FAB wet sanded, primed and painted. Alernate air
|
Details
|
|
|
|
04-20-2018
|
4.00
|
Drill and rivet heat and alternator ducts. Rivete
|
Details
|
|
|
|
04-18-2018
|
1.00
|
More forward cowl trim and FAB micro sanding
|
Details
|
|
|
|
04-18-2018
|
1.00
|
|
Details
|
|
|
|
04-17-2018
|
3.00
|
Oil cooler duct riveted, heat duct cut, alternator
|
Details
|
|
|
04-16-2018
|
2.50
|
Glassed alternate air hole and micro on FAB, cut o
|
|
|
|
04-15-2018
|
2.00
|
Snorkel test fit, alternate air hole cut. Cowl in
|
Details
|
|
|
04-14-2018
|
6.00
|
FAB, finished all brackets. Nutplates to hold dow
|
Details
|
|
|
|
04-12-2018
|
3.00
|
FAB work continues
|
Details
|
|
|
|
04-11-2018
|
7.00
|
FAB work continues - made VA 132 brackets and baff
|
Details
|
|
|
04-10-2018
|
4.00
|
Snorkel fitting to left inlet, drilled holes, cut
|
Details
|
|
|
04-09-2018
|
1.00
|
More baffle riveting, clearanced forward cowling p
|
Details
|
|
|
|
04-07-2018
|
5.00
|
Finished top baffle trim
|
Details
|
|
|
|
04-06-2018
|
2.00
|
Baffle marking and initial top trim
|
Details
|
|
|
04-05-2018
|
3.00
|
Baffling fitting and trimming, fabricated front cl
|
Details
|
|
|
04-04-2018
|
4.00
|
Baffling fitting and trimming
|
Details
|
|
|
|
04-02-2018
|
2.00
|
Baffling fitting and trimming
|
Details
|
|
|
|
04-01-2018
|
4.00
|
Baffling fabrication, deburr and riveting
|
Details
|
|
|
|
04-01-2018
|
1.50
|
Baffling fabrication and riveting
|
Details
|
|
|
03-31-2018
|
3.00
|
Baffling fabrication and deburring
|
Details
|
|
|
|
03-29-2018
|
0.50
|
Started baffles
|
Details
|
|
|
|
03-28-2018
|
2.00
|
Cowling oil door sanding, cowl sanding
|
Details
|
|
|
|
03-27-2018
|
2.00
|
Oil Door Fabrication finished. Hinges drilled. G
|
Details
|
|
|
03-25-2018
|
3.00
|
Oil Cooler Lines - Firesleeve, oil door fabricatio
|
Details
|
|
|
03-24-2018
|
5.00
|
Installed oil cooler mount, cooler, plenum and cab
|
Details
|
|
|
03-23-2018
|
2.00
|
Painted oil cooler plenum white. RTV plenum mount
|
Details
|
|
|
03-22-2018
|
2.00
|
Sanded upper intersection fairing.
|
Details
|
|
|
|
03-21-2018
|
1.00
|
Glassed upper intersection fairing
|
Details
|
|
|
|
03-18-2018
|
3.00
|
Cowling - removed cover plates an drilled nutplate
|
Details
|
|
|
03-17-2018
|
3.00
|
Sanded forward cowl and glassed hinge pin cover pl
|
Details
|
|
|
03-16-2018
|
3.00
|
Front cowling micro sanding, OC plenum sanding
|
|
|
|
03-15-2018
|
3.00
|
Oil Cooler plenum sanding and micro. Cowling fron
|
Details
|
|
|
|
03-14-2018
|
3.50
|
Oil Cooler Plenum layup and cowl edge sanding
|
Details
|
|
|
03-13-2018
|
2.00
|
Riveted horizontal side hinges.
|
Details
|
|
|
03-12-2018
|
2.50
|
Cowling horizontal hinge prep
|
Details
|
|
|
|
03-11-2018
|
3.50
|
Drilled, shaped upper intersection fairings and op
|
Details
|
|
|
03-09-2018
|
2.00
|
Oil Cooler gap seals fabricated and riveted
|
|
|
|
03-08-2018
|
3.50
|
Cowl side hinges, upper and lower drilled
|
Details
|
|
|
03-07-2018
|
4.00
|
Cowl edge gap sanding, oil cooler plate fabricated
|
Details
|
|
|
03-06-2018
|
2.00
|
Trimmed and sanded left lower cowling edge
|
Details
|
|
|
|
03-04-2018
|
3.00
|
Lower Cowl right edge glassing and oil cooler fitm
|
Details
|
|
|
03-03-2018
|
4.00
|
Lower Cowl fitted, trimmed and drilled to firewall
|
Details
|
|
|
03-02-2018
|
2.00
|
Lower Cowling - Trimmed gear area and aft bottom c
|
|
|
|
03-01-2018
|
3.00
|
Top Cowl - final forward trim, trimmed aft edge an
|
Details
|
|
|
02-28-2018
|
3.00
|
Cowling - leveled fuselage, marked spinner hole.
|
Details
|
|
|
02-27-2018
|
1.50
|
Cowling - measured perimeter, forward cowl/spinner
|
Details
|
|
|
|
05-22-2017
|
2.00
|
Deburred wheel paint fairling, removed deburred en
|
Details
|
|
|
05-21-2017
|
8.00
|
Riveted Skybolt Cowl Strips - Sides/Bottom and FW
|
Details
|
|
|
05-20-2017
|
4.00
|
Engine Mount Drilled to FW
|
Details
|
|
|
|
12-01-2016
|
1.50
|
Fabricated bushings for elev. bellcrank, large pus
|
Details
|
|
|
01-24-2016
|
3.50
|
Battery Box
|
Details
|
|
