KitLog pro

Powered By Kitlog Pro v2.0

Baker's RV-6
Work Logs Found: 126
Category Work Time: 216 Hours
 Date
Hours
Work Log Summary

Details

 05-10-2014
3.00
Spiral-wrapped Wires/Removed Aileron Trim Springs
Details
       

 05-09-2014
3.00
Spiral-wrapped Wires under Seats
Details

 04-17-2014
1.00
Tied Wires behind Panel to Fuel Line Air Vent Tubi
Details
       

 04-16-2014
0.50
Ran ELT and Push-to-Talk Wires along Rt Sidewall
Details
     

 03-08-2014
1.50
Left Wing Nav Light Power Wire Redone
Details
       

 03-07-2014
2.00
Connected Nav Light Power Wires/Left Doesn't Work
Details

 02-20-2014
1.00
Nav Light Power Wires in Fuselage
Details

 01-14-2014
0.50
Left Nav/Strobe Light
Details
       

 01-14-2014
1.50
Installed Left Nav/Strobe Light in Wing Tip
Details
       

 01-13-2014
1.00
Right Nav/Strobe Light Wiring
Details
       

 01-13-2014
0.50
Crimped Molex Pins on Right Strobe Wire
Details
     

 01-12-2014
2.00
Landing Lights Work!
Details
       

 01-12-2014
0.50
Assisted with Landing Light Installation
Details
     

 01-11-2014
0.30
Molex Pins on Right Landing Light Wires
Details

 01-10-2014
0.50
Crimped Right Landing Light Wires
Details
     

 01-02-2014
2.50
Ran Nav Power Wire thru Left Wing
Details
     

 01-02-2014
1.50
Helped Run Nav Power Wire thru Left Wing
Details

 12-27-2013
1.00
Ran Nav Power Wire thru Right Wing Loom
Details

 12-27-2013
0.50
Assisted with Running Right Nav Power Wire
Details

 12-27-2013
1.00
Assisted with Running Nav Power Wire
Details

 12-13-2013
1.00
Taxi Light Wires in Right Wing
Details
     

 10-01-2013
1.50
Ran Strobe Wiring
Details
       

 09-30-2013
0.50
Helped with Strobe Wiring
Details

 09-30-2013
2.00
Determined Strobe Wiring/Visitor
Details

 09-25-2013
1.00
Ran Strobe Wiring and Nav Coax Thru Wings
Details
       

 07-13-2013
2.00
Completed Left Landing Light Wiring in Wing
Details
       

 07-12-2013
3.00
Made Connectors for AeroLED Lights
Details
       

 07-12-2013
2.00
Landing Light Wiring
Details
       

 04-16-2012
1.50
Crimped Dsub Terminals onto Wires
Details
     

 04-12-2012
1.00
Found Amp Wires too Short/Pulled out Dynon
Details
       

 04-11-2012
2.00
RTV under Clock/Quick Disconnects in TruTrak
Details
       

 04-11-2012
3.00
Photos-Pitot and Static Tubing into the ADI
       

 04-10-2012
2.00
P1 Connector
Details
       

 04-10-2012
2.00
16 AWG Starter Wire
Details
       

 04-09-2012
3.00
Roll Servo Wires/Pinned Mag Wires
Details
       

 04-09-2012
1.00
FireBarrier Applied over Grommets in Firewall
Details
       

 04-06-2012
1.50
Finished Dsub Connector-Roll Servo
Details
       

 04-05-2012
1.00
Made Jumper Wire for Starter/Roll Servo Wires
Details
       

 04-04-2012
3.00
Made Power Wires for Lightspeed Ignition
Details
       

 04-04-2012
2.50
Lightspeed Wires to Battery/Roll Servo Wires
Details
       

 04-03-2012
2.00
Wired Tach Transducer to RPM Wire and Power
Details
       

 04-03-2012
1.30
Tach Transducer Wire
Details
       

 04-03-2012
0.20
Labeled Lightspeed Power Wire
Details
     

 04-02-2012
1.00
Pilot Stick Grip P7 Reassembled
Details
       

 04-02-2012
3.50
Made Output Connector for Lightspeed Control Box
Details
       

 03-28-2012
1.50
Lightspeed Ignition
Details
       

 03-28-2012
0.50
Found Smoke System Wiring Problem
Details

 03-28-2012
2.00
Chased Wiring Problem-Smoke System Ident Button
Details
       

 03-27-2012
2.50
Reassembled the P7 Connector
Details
       

 03-27-2012
2.00
Added Wire in Pilot Stick Grip for Smoke System
Details
       

 03-26-2012
1.50
Zaon Power Wire on Bus Bar
Details
     

 03-26-2012
1.50
Soldered Zaon Data Wire into Garmin Wiring
Details
       

 03-26-2012
1.50
Modified Pilot Stick Grip Wiring for Smoke System
Details
       

 03-26-2012
1.50
Completed Zaon Wiring
Details
       

 03-25-2012
0.50
Crimped Molex Pins onto Garmin 496 Data Wires
Details
     

 03-24-2012
2.00
Made New GPS Wire/Sealed Firewall PassThru's
Details
       

 03-23-2012
1.00
Screwdriver Access Holes Drilled for Shelf
Details
     

 03-23-2012
1.00
GPS/XM Antenna Shelf Construction #4
Details
       

 03-23-2012
1.00
GPS/XM Antenna Shelf Construction #3
Details
       

 03-23-2012
2.00
GPS/XM Antenna Shelf Construction #2
Details
       

 03-23-2012
1.00
GPS/XM Antenna Shelf Construction
Details
       

 03-22-2012
1.00
More Wires Inserted into P1
Details
     

 03-22-2012
2.00
Installed Firewall Pass-through for GPS Wires
Details
       

 03-22-2012
2.00
Garmin Data Cable
Details
       

 03-21-2012
1.00
P7 Connector/Garmin GPS & XM Antennas
Details
       

 03-19-2012
1.00
Nav Wire Run to Left Wing
Details
       

 03-19-2012
2.00
Comm Antenna Installed
Details
       

 03-19-2012
2.00
Antenna Wires Positioned/Ran P4 Wires
Details
       

 03-19-2012
2.00
Antenna Wires Connected/Antenna Installed
Details
       

 03-17-2012
2.00
Finished Flap Wires/Comm Antenna Coax Wires
Details
       

 03-17-2012
1.00
Comm Antennas Run thru Center Spar Area
Details
       

 03-16-2012
1.00
Rotated Smoke System Arm/On Switch
Details
       

 03-16-2012
2.00
Rewired Flap Switch
Details
       

 03-16-2012
1.00
Attached Battery and Master Relay Wire
Details
       

 03-15-2012
1.00
Labeled Flap Switch and Strobe Power Wires
Details
       

 03-15-2012
1.00
Joined the Two EDC-10A Connectors
Details
       

 03-15-2012
1.00
Inserted EDC-10A Wires into Connector
Details
       

 03-13-2012
0.50
Zaon XRX Interface Cable Assembly
Details
     

 03-13-2012
2.00
Smoke System Power/EDC-10A Wiring
Details
       

 03-13-2012
2.00
Pitch Servo Wiring/Smoke System Power
Details
       

 03-12-2012
1.00
Smoke System Wiring
Details
       

 03-12-2012
2.00
Ran Wires along Center Section/Smoke Wires
Details
       

 03-12-2012
2.00
Finished Smoke System Tubing
Details
       

 03-11-2012
0.50
Trimmed Center Section by Heat Cable
Details
     

 03-11-2012
1.50
Smoke System Tubing Routing
Details
       

 03-11-2012
2.00
Riveted Bracket to Subpanel/Smoke Tubing
Details
       

 03-10-2012
1.00
Pitot Tubing/Trimmed Floor Center Cover
Details
       

 03-10-2012
2.00
Made Bracket for Attaching P4S Connector
Details
       

 03-09-2012
1.50
Static Tubing into EFIS/Airspeed Indicator
Details
       

 03-09-2012
1.50
Photos-Static Tubing
       

 03-09-2012
1.50
Laced up Wires/Floor Center Section in Fuselage
Details
       

 03-07-2012
2.00
Pinned P4S Connector and Clamped in place
Details
       

 03-07-2012
2.00
Photos-P4S Connector
       

 03-06-2012
1.00
P4S Connector Partially Pinned
Details
       

 03-06-2012
0.50
Ground Wires Screwed Together
Details
     

 03-06-2012
1.00
Crimped Three Ground Wires into One Ground
Details
       

 03-06-2012
2.00
Began to Pin P4S Connector
Details
       

 03-05-2012
1.00
Wires Stripped in Preparation of Making Connector
Details
     

 03-05-2012
4.00
Reran Headset Wires on Left Side
Details
       

 02-29-2012
2.50
Replaced Wire Loom on Right Side/Nutplate
Details
       

 02-29-2012
0.50
Installed Jacks on Bulkheads
Details
       

 02-28-2012
2.50
Wiring LEMO Plugs
Details
       

 02-28-2012
2.50
Right Headset Jack Wires Resoldered
Details
       

 02-27-2012
3.00
Headset Jack Wires Run/LEMO Plug Wires
Details
       

 02-22-2012
5.00
Jacks installed on Left Side/Wire Sleeve Used
Details
       

 02-21-2012
3.00
Soldered Last Two Headset Jacks
Details
       

 02-21-2012
2.50
Headset Wire Run-Left Side/Finished Jacks Wiring
Details
       

 02-20-2012
4.50
Received Slo-Blo Fuse/Soldered Headset Jacks
Details
       

 03-07-2010
1.00
Canopy Rollers/Clear Heat-Shrink over Labels
Details
     

 03-06-2010
6.50
Wire Labels/Drilled out Rivets in Top Skin
Details
       

 03-06-2010
3.50
Reviewed/Corrected Flap Wire Runs
Details
       

 03-02-2010
2.00
Started Labeling Wires
Details
       

 03-01-2010
0.10
Photos-Transponder BNC/P-1 Connector
       

 03-01-2010
0.10
Photos 3-FPS Wires, Transponder
       

 03-01-2010
0.10
Photos 2-Flap Wires and Transponder Coax
       

 03-01-2010
5.50
Organized Flap Wires/P1 Connector Reseated
Details
       

 02-25-2010
0.10
Photos-Flap System and AOA Switch Wiring
       

 02-25-2010
0.10
Photos 3-Position the Smoke System Remote Switch
       

 02-25-2010
0.10
Photos 2-Flap System and AOA Switch Wiring
       

 02-24-2010
4.50
Flap and AOA Wiring
Details
       

 02-22-2010
3.00
Pinned Pitch Servo Wires/Changed Smoke Reservoir
Details
       

 02-17-2010
6.00
Wiring/Static Tube Clip
Details
       

 02-17-2010
3.00
Strobe Power Supply/EDC-10A Wiring/Smoke Sys Tubin
Details
       

 02-17-2010
0.10
Photo-Strobe Power Supply/ELT Wiring
     

 01-27-2010
0.10
Ran Wires for the Pitch Servo/Strobe Power Supply
Details
       

 01-27-2010
3.50
Ran Wire for Strobes/Pinned Magnetometer
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.