Date
|
Hours
|
Work Log Summary
|
Details
|
01-17-2021
|
2.00
|
Riveting & More. See Notes to Right.
|
Details
|
|
|
01-16-2021
|
2.50
|
Buff, Clean, Prime & More. See Notes to Right.
|
Details
|
|
|
01-15-2021
|
2.75
|
Cut, Trim, Debur, Countersink & Rivet Canopy Clips
|
Details
|
|
|
|
01-13-2021
|
0.75
|
Install Defrost Fans
|
|
|
|
|
01-12-2021
|
1.00
|
Placed Canopy Back Onto Airframe
|
|
|
|
01-11-2021
|
3.25
|
See Notes to Right
|
Details
|
|
|
01-09-2021
|
2.50
|
Remove Aft Tape Line. See Notes to Right.
|
Details
|
|
|
01-08-2021
|
1.75
|
Sand Filled Areas. 1 More Fill Required
|
|
|
|
|
01-01-2021
|
1.50
|
Sand & Fill Low Spots in Canopy Fairing
|
|
|
|
12-31-2020
|
1.50
|
Continue Sanding Canopy Fairing
|
|
|
|
|
12-28-2020
|
0.75
|
Install Rear Canopy Seal & Tighten Area 3 Screws
|
|
|
|
|
12-27-2020
|
0.75
|
Applied Top Coat of Resin to Canopy Front Edge
|
|
|
|
12-26-2020
|
0.50
|
Prep Canopy for Resin Skim Coat
|
|
|
|
|
12-24-2020
|
1.00
|
Continue Sanding Canopy Fairing - Getting Close
|
|
|
|
12-22-2020
|
1.75
|
Sanding then Removed Forward Tape to Feather
|
|
|
|
12-19-2020
|
1.50
|
Continue Sanding Canopy Fairing
|
|
|
|
|
12-18-2020
|
1.00
|
Continue Sanding Canopy Fairing
|
|
|
|
12-17-2020
|
1.50
|
Continue Sanding Canopy Fairing
|
|
|
|
12-16-2020
|
1.00
|
Continue Sanding Canopy Fairing
|
|
|
|
|
12-15-2020
|
1.00
|
Remove Peel Ply & Begin Sanding Canopy Fairing
|
|
|
|
|
12-13-2020
|
2.50
|
Install Fiberglass Panels A & D
|
|
|
|
12-13-2020
|
3.00
|
Complete Buildup of Canopy 4" Lip w/Fiberglass
|
|
|
|
12-11-2020
|
2.50
|
Cut all Remaining Fiberglass Strips & Shapes +
|
Details
|
|
|
|
12-10-2020
|
1.75
|
Completd Fabrication of Wear Strips & Installed
|
Details
|
|
|
|
12-09-2020
|
1.50
|
Sand Canopy & Began Fabricating Wear Strips
|
|
|
|
|
12-07-2020
|
2.15
|
Canopy Works - See Notes to Right.
|
Details
|
|
|
12-05-2020
|
3.00
|
Final Sanding of Gap Filler - See Notes to Right
|
Details
|
|
|
12-04-2020
|
0.75
|
Mix & Apply Light 2nd Filler Coat to Gap Fill Area
|
|
|
|
12-04-2020
|
4.00
|
Begin Sanding of Gap Filler
|
|
|
|
12-03-2020
|
1.00
|
Apply 1st Layer of Filler to Canopy Gap
|
|
|
|
|
12-02-2020
|
1.50
|
Completed Scuffing Canopy for Fiberglasss Work
|
|
|
|
12-01-2020
|
0.75
|
Sand Down Left Side of Canopy
|
|
|
|
|
12-01-2020
|
1.00
|
Begin Scuffing Up Canopy for Fiberglasss Work
|
|
|
|
11-30-2020
|
1.00
|
Sand Down Right Side of Canopy
|
|
|
|
11-29-2020
|
3.50
|
Attach 7ea. Canopy Clips. Prep Canopy for Sanding
|
|
|
|
11-27-2020
|
1.50
|
Tighten Canopy Hardware - See Notes to Right
|
Details
|
|
|
|
11-22-2020
|
1.75
|
Install (not tighten) Canopy Hardware
|
|
|
|
11-20-2020
|
2.50
|
Fit & Notch Aft Canopy Seal. Gather Fastenings
|
|
|
|
11-19-2020
|
2.00
|
Finish Countersinking Aft Canopy Edge
|
|
|
|
|
11-15-2020
|
2.00
|
Began Countersinking Aft Canopy Edge
|
|
|
|
|
11-13-2020
|
3.50
|
Remove Canopy - See Notes to Right
|
Details
|
|
|
|
11-11-2020
|
2.50
|
Remove Canopy - See Notes to Right
|
Details
|
|
|
|
11-09-2020
|
1.00
|
Prep Canopy & Frame for Final Attachment
|
|
|
|
|
10-29-2020
|
1.75
|
Completed Countersinking Canopy Rails Edges
|
|
|
|
|
10-28-2020
|
0.75
|
Began Countersinking Canopy Rails Edges for #6.
|
|
|
|
|
10-12-2020
|
0.50
|
Fabricate Canopy Transition Curve Gauge
|
|
|
|
|
10-11-2020
|
2.50
|
Canopy Works. See Notes to Right.
|
Details
|
|
|
10-10-2020
|
1.50
|
Canopy Misc. See Notes to Right.
|
Details
|
|
|
|
10-09-2020
|
4.00
|
Canopy Works. See Notes to Right.
|
Details
|
|
|
|
10-08-2020
|
0.75
|
Hinge Cover Works. See Notes to Right...
|
Details
|
|
|
|
10-07-2020
|
1.75
|
Mark & Tape Canopy's Aft & Forward Fairing Lines
|
|
|
|
|
10-04-2020
|
0.50
|
Fabricate Canopy 7/8" Aft Limit Tape Gauge
|
|
|
|
|
10-03-2020
|
0.75
|
Fabricate Canopy Sanding Block
|
|
|
|
|
09-26-2020
|
3.50
|
Enlarge #40 Pilot Holes in Canopy to #27
|
|
|
|
09-25-2020
|
4.25
|
Drill/Match Drill #40 Pilot Holes in Canopy
|
|
|
|
09-24-2020
|
1.25
|
Weights Added & Final Check of Canopy. Drill Next
|
|
|
|
09-22-2020
|
1.50
|
Final Grinding, Sanding, Fitting of Canopy
|
|
|
|
09-21-2020
|
1.25
|
Continue Chamfering Canopy Front Edge - Close
|
|
|
|
|
09-19-2020
|
1.00
|
Continue Chamfering Canopy Front Edge
|
|
|
|
|
09-16-2020
|
1.25
|
Continue Chamfering Canopy Front Edge
|
|
|
|
|
09-14-2020
|
1.50
|
Chamfered Canopy Front Edge @ Point Oscar
|
|
|
|
09-13-2020
|
0.25
|
Fabricate 0.40 Feeler Gauge
|
|
|
|
|
09-12-2020
|
2.50
|
Sit Canopy in Frame. See Notes to Right
|
Details
|
|
|
09-10-2020
|
1.50
|
Prep Frame for Canopy's Initial Fit. Add Template
|
|
|
|
09-10-2020
|
1.00
|
Final Sanding of Widow's Leading Edge
|
|
|
|
|
09-09-2020
|
2.00
|
Begin Final Sanding of Widow's Leading Edge
|
|
|
|
|
09-08-2020
|
1.75
|
Trim & Fit sides of Window to Clear Skin Supports
|
|
|
|
|
09-06-2020
|
1.50
|
Continue Countersinking Window - Leading Edge
|
|
|
|
09-05-2020
|
2.50
|
Complete Installation of Canopy Locking Mechanism
|
|
|
|
|
09-04-2020
|
3.50
|
Begin Installation of Canopy Locking Mechanism
|
|
|
|
|
09-03-2020
|
1.00
|
Tap Rollbar for #6 Screws
|
|
|
|
09-03-2020
|
2.00
|
Continue Countersinking Window for #6 Screws
|
|
|
|
09-02-2020
|
2.00
|
Sanding Window Eges & Started Countersinking
|
|
|
|
|
09-01-2020
|
0.75
|
Final Rivet Side Skins to Fuselage
|
|
|
|
|
09-01-2020
|
1.00
|
Begin Trimming Front Edge of Window
|
|
|
|
|
08-31-2020
|
1.25
|
Window - Final Drill #27 & Relieve Inside Holes
|
|
|
|
|
08-31-2020
|
1.75
|
Rivet F-01474A-L&R to Fuselage
|
|
|
|
|
08-31-2020
|
1.50
|
Final Drill #27 & Dimple Fuselage for Window
|
|
|
|
|
08-30-2020
|
1.50
|
Remove, Trim & Install Canopy Frame onto Aircraft
|
|
|
|
08-28-2020
|
0.50
|
Trial Fit Canopy Frame onto Aircraft
|
|
|
|
|
08-26-2020
|
3.00
|
Complete Drilling Sequence of Window Installation
|
|
|
|
|
08-24-2020
|
1.50
|
Begin Drilling Sequence of Window Installation
|
|
|
|
|
08-22-2020
|
1.75
|
Mark Edging, Remove Film. Enlarge Roll Bar Holes
|
|
|
|
08-20-2020
|
2.25
|
Cut Notches in Rear Window - Buff, Polish, Fit
|
|
|
|
08-19-2020
|
1.50
|
Final Fit Window for Notching
|
|
|
|
|
08-17-2020
|
1.50
|
Prep Window for Installation
|
|
|
|
