KitLog pro

Powered By Kitlog Pro v2.0

Norris's RV Construction
Work Logs Found: 124
Category Work Time: 668 Hours
 Date
Hours
Work Log Summary

Details

 06-12-2020
7.00
Side panels

 06-11-2020
5.00
Continue installing side panels

 06-10-2020
6.00
Installed the right passenger seat cover panel

 05-04-2020
3.00
Install and seal the oil cooler holder on the fire

 04-24-2020
4.00
Tested alternative panel labeling options

 04-23-2020
8.00
Labeled most of the items on the panel

 04-22-2020
6.00
Got panel ready for covering and mostly covered
     

 04-21-2020
6.00
Continue laying out and drilling holes in the pane

 04-20-2020
8.00
Layi0ut and cut holes for switches and EFII displa
     

 04-17-2020
6.00
Made and tapped a ground plate. Painted subpanel
     

 04-15-2020
8.00
EIS, backplates, and relay holder
Details
       

 04-14-2020
2.50
Started designing a holder for the EIS box

 04-13-2020
2.50
Installed flap position sensor
     

 04-10-2020
6.00
Install flap system
     

 04-08-2020
8.00
Worked on installing controll tubes and stick

 04-07-2020
8.00
Baggage door
Details
       

 04-03-2020
4.00
Riveted half lthe baggage door
     

 04-02-2020
8.00
Buss Mgr bracket. Switch layout. Start baggage Dr.

 03-31-2020
4.00
Wrapping center dadio stack
     

 03-31-2020
3.00
Modified and wrapped Throttle and Prop brackerts
     

 03-30-2020
8.00
Riveted covering and cut out openings
     

 03-28-2020
2.50
covering the center c onsole radio stack
     

 03-27-2020
8.00
Continue working on makinmg the radio stack

 03-25-2020
8.00
Continue working on the radio stack center console

 03-24-2020
8.00
Framework of center console radio rack
     

 03-18-2020
4.00
Transponder rack
Details
       

 03-17-2020
6.00
Developing and making transsponder brackets

 03-16-2020
4.00
Finished cutting out the G3X panel openings
       

 03-15-2020
8.00
Making land installing structural supports in Pane

 03-10-2020
7.00
Worked on stiffening the fold down instrument pane

 03-09-2020
8.00
Installed battery contactors plus work on panel
Details
       

 02-19-2020
4.00
Installed fuel lines from tunnel to aircraft skin
     

 02-18-2020
5.00
Installed a new parking brake acuator and pumps

 02-17-2020
4.00
Installed battery cables thru firewall

 02-14-2020
2.00
Install AHRS bracket
     

 02-04-2020
9.00
Rudder peddles and the remaining brake lines.
     

 02-03-2020
3.00
dudder peddles and brake lines

 01-31-2020
8.00
Brake and fuel lines instulation.
     

 01-30-2020
4.00
Continued working on the parking brake and rack

 01-29-2020
8.00
See details
Details
     

 01-28-2020
3.00
Started testing electric parking brake actuator

 01-27-2020
9.00
Making new fuel lines. Didn't like Fridays attemp
     

 01-24-2020
8.00
Continue working on fuel lines

 01-23-2020
3.00
Designing the fuel pumps and filters layout

 01-22-2020
4.00
Brake lines and fuel selector
Details

 01-21-2020
6.00
Rudder peddles install and start brake lines
     

 01-14-2020
3.00
Finished adjusting and installing the bsaggage bac
     

 01-13-2020
3.00
Finished the other half of the back baggage wall
     

 01-10-2020
9.00
Installing skybolt quarter turn fasteners
Details
     

 01-07-2020
6.00
Continue working on the forward skin and panel

 01-06-2020
9.00
Made panel attachments
Details
       

 01-02-2020
3.50
Aligning and riviting baggage and rear seat panels

 12-26-2019
6.00
Continued with the rear seat and baggage floors
     

 12-23-2019
8.00
Baggage floor and rear seat cover ready to rivet
     

 12-20-2019
6.00
Continue working on baggage floor, rear seat floor

 12-19-2019
3.00
Preping passenger seat bottoms

 12-13-2019
5.50
Riveted the passenger floor plans down

 12-11-2019
5.00
Prep and start installing passenger floor pan

 12-06-2019
7.50
Install smuft tubes and start back seat floor
     

 09-24-2019
2.00
Continue riviting the tail cone to the forward fus

 09-23-2019
2.00
Continue riviting the tail cone to the forward fus

 09-20-2019
2.00
Riveting the tail cone to thefuselage

 09-16-2019
7.00
Connect tail cone to fuselage
       

 09-12-2019
7.00
Installed fire protective blanket
     

 09-11-2019
8.00
Finishing the hinged panel
       

 09-10-2019
4.00
Working on making a hinged fold down panel

 08-21-2019
5.00
assermble the upper fuselage assembly
     

 08-19-2019
4.00
Rear air vents
Details

 08-16-2019
2.00
Started on upper forward fuselage assembly

 08-15-2019
5.00
Installed L and R steps
     

 08-14-2019
3.00
Installed the passenger fresh air vents
     

 08-12-2019
5.00
installed the landing gear brackets
     

 08-09-2019
8.00
Put in copilots floor and started on L gear suppor
       

 08-08-2019
5.00
Finish riveting sides. Install Pilot floorboard

 08-07-2019
6.00
Continue riveting side skins

 08-05-2019
8.00
Continue riveting forward and mid side skins

 08-02-2019
7.00
Installed side skins and started riveting
     

 08-01-2019
3.00
Continue riveting the forwerd longerons

 07-31-2019
3.00
start fiveting longerons to the firewall

 07-16-2019
7.50
dimpling tghe side skins and finish counterrtsinki

 07-12-2019
6.00
More drilling and countersinking

 07-11-2019
6.00
Install and match drill the forward side skin
     

 07-10-2019
6.50
Attached mid skins and match drilled
     

 06-28-2019
9.00
Curved the 4 side skins bottoms
       

 06-27-2019
6.00
Shaping the mid and forward Longeroons

 06-26-2019
6.00
Riviting Mid and Fwd sections and Longerons
Details

 06-25-2019
1.50
Completed drilling for the Right main gear

 06-21-2019
4.50
mid seat supports and L main gear support
Details

 06-20-2019
7.50
Seat pans and side structure
     

 06-19-2019
7.00
Mated fwd land mid fuselage
     

 06-18-2019
7.00
Continue riviting
     

 06-17-2019
9.00
Riviting forward fuselage
Details
     

 06-14-2019
8.00
Rivit forward bottom skin
Details
     

 06-13-2019
5.00
Firewall cleko'd to forward bottom skin
Details
     

 06-12-2019
2.00
Fwd Fusalage Floor- set parts and start match dril

 01-02-2019
2.00
Continue working on the fwd fuselage bulkhead asm

 01-01-2019
1.50
Continue working on the fwd fuselage bulkhead asm

 12-28-2018
7.50
Fwd Fugelage bulkhead sub assembly
     

 12-11-2018
3.00
Finished riveting the Firewall section 27

 11-30-2018
2.00
Rivet in the Nose Gear Tension Fittings
     

 11-28-2018
3.00
Continue riviting onfirewall parts

 10-22-2018
2.00
Start firewall aft attachments

 10-19-2018
2.00
Finish riveting firewall

 10-16-2018
4.00
Riveting firewall

 10-05-2018
3.00
Readying parts for firewall

 08-24-2018
2.00
lContinue riveting lower aft fuselage

 08-22-2018
5.00
Riveting Aft fuselage bottom skins on

 08-21-2018
5.00
Finished DCrilling, deburring, and dimpling bottom
       

 08-20-2018
6.00
Aligning and clekoing and match driling bottom ski

 08-17-2018
5.50
Riveting the last part of the aft lower fuselage
     

 08-16-2018
4.00
Started riveting aft of midsection

 08-15-2018
4.00
More mid fuselage assembly
     

 08-14-2018
8.00
Still working on mid fuselage

 08-13-2018
9.00

     

 08-10-2018
8.00
Completed the mid fuselage bulkheads

 08-09-2018
5.00
Working on the Mid section aft spar
     

 08-08-2018
6.00
Finished the forward mid fuselage bulkhead.

 08-07-2018
7.00
Added gear legs and began riviting spar
     

 08-06-2018
6.00
Assemble the Mid Fuselage Spar
       

 08-02-2018
5.00
Finished inventorying
       

 08-01-2018
6.00
Inventorying parts

 07-19-2018
2.00
Begin unpacking and inventorying
     

 01-04-2018
1.50
Longeron for rear fuselage

 12-22-2017
9.00
Begin making the ribs for the rear fuselage










Copyright © 2001-2021 Matronics. All Rights Reserved.