Date
|
Hours
|
Work Log Summary
|
Details
|
02-03-2024
|
1.00
|
Installed seat backs and seat cushions
|
|
|
|
02-02-2024
|
2.00
|
Installed seat back brackets
|
|
|
|
01-30-2024
|
1.00
|
Installed outboard seat belt brackets
|
|
|
|
01-28-2024
|
2.00
|
Installed passenger seat sliders and seat pan
|
|
|
|
01-27-2024
|
2.00
|
Installed pilot seat sliders and seat pan
|
|
|
|
12-23-2023
|
2.00
|
Installed the seat base panels
|
|
|
|
12-10-2023
|
4.00
|
Installed control tunnel side panels
|
Details
|
|
|
11-26-2023
|
2.00
|
Replaced starter key switch with a push button
|
Details
|
|
|
10-29-2023
|
5.00
|
Drilled console side panels and installed nut plat
|
|
|
|
10-22-2023
|
3.00
|
Installed the front torque tube bearing
|
|
|
|
09-19-2023
|
4.00
|
Finished install and started up engine
|
Details
|
|
|
09-18-2023
|
6.00
|
Trimmed and fitted cowling to aircraft
|
Details
|
|
|
09-18-2023
|
2.00
|
Installed prop on engine
|
|
|
|
|
09-18-2023
|
5.00
|
Installed fuel header tank and fuel lines
|
Details
|
|
|
09-17-2023
|
4.00
|
Mounted the engine
|
Details
|
|
|
09-17-2023
|
5.00
|
Installed the engine electrical
|
Details
|
|
|
09-17-2023
|
2.00
|
Installed heater and center console switch panel
|
|
|
|
09-15-2023
|
0.00
|
My engine arrived!
|
Details
|
|
|
09-13-2023
|
2.00
|
Drilled forward top skin
|
|
|
|
09-04-2023
|
1.00
|
Made drill guides for forward top skin
|
Details
|
|
|
08-05-2023
|
4.00
|
Installed nose wheel steering rods
|
Details
|
|
|
05-31-2023
|
0.00
|
She is on her feet!
|
|
|
|
05-29-2023
|
3.00
|
Installed nosewheel strut and wheel
|
Details
|
|
|
02-26-2023
|
2.00
|
Mounted main tires on rims
|
Details
|
|
|
02-26-2023
|
2.00
|
Installed wheels on main gear
|
|
|
|
02-26-2023
|
1.00
|
Bolted spacer to nose wheel fork
|
Details
|
|
|
02-12-2023
|
2.00
|
Mounted nose wheel tire on rim
|
Details
|
|
|
01-29-2023
|
3.00
|
Installed main gear
|
Details
|
|
|
01-22-2023
|
1.00
|
Trimmed nose gear lower bearing
|
Details
|
|
|
01-22-2023
|
1.00
|
Installed SS rivets in cabin frame gusset
|
Details
|
|
|
01-08-2023
|
2.00
|
Rivetted side skin and firewall
|
|
|
|
12-30-2022
|
3.00
|
Finished side skin stiffeners passenger side
|
Details
|
|
|
12-10-2022
|
4.00
|
Finished side skin stiffeners pilot side
|
Details
|
|
|
12-03-2022
|
1.50
|
Installed steering rod swivels
|
Details
|
|
|
12-03-2022
|
1.00
|
Drilled and clecoed firewall to side skin
|
|
|
|
12-03-2022
|
2.00
|
Began fabricating side skin stiffeners
|
|
|
|
11-26-2022
|
1.00
|
Prepped firewall for drilling to side skin
|
Details
|
|
|
11-05-2022
|
3.00
|
Installed rudder & brake pedals & brake cylinders
|
|
|
|
10-29-2022
|
1.00
|
Test fit rudder & brake pedals
|
|
|
|
10-01-2022
|
5.00
|
Prep & drill brake pedals
|
|
|
|
09-11-2022
|
1.50
|
|
|
|
|
09-11-2022
|
1.00
|
|
|
|
|
09-03-2022
|
1.00
|
Installed passenger seat support brackets
|
|
|
|
08-28-2022
|
1.50
|
Riveted cabin frame - pilot side
|
|
|
|
08-28-2022
|
1.50
|
Riveted cabin frame - passenger side
|
|
|
|
08-27-2022
|
7.00
|
Installed landing gear brackets
|
|
|
|
08-20-2022
|
7.00
|
Joined rear and forward fuselage halves
|
|
|
|
08-14-2022
|
8.00
|
Re-assembled forward fuselage
|
|
|
|
10-02-2021
|
4.00
|
Continued reassembly of lower forward fuselage
|
|
|
|
09-25-2021
|
2.00
|
Reassemble lower forward fuselage
|
Details
|
|
|
|
09-18-2021
|
2.00
|
Drilled and installed brake cylinder supports
|
Details
|
|
|
09-06-2021
|
4.00
|
Install access panels in baggage floors
|
Details
|
|
|
09-05-2021
|
3.00
|
Cut holes in baggage floors for access panels
|
|
|
|
07-05-2021
|
4.50
|
Disassemble and debur forward fuselage
|
|
|
|
|
05-31-2021
|
2.50
|
Drilled forward side skins
|
|
|
|
05-09-2021
|
1.00
|
Completed assembly of firewall
|
|
|
|
05-09-2021
|
2.00
|
Clecoed forward side skins to fuselage
|
|
|
|
05-02-2021
|
3.00
|
Began assembling firewall
|
Details
|
|
|
05-01-2021
|
3.00
|
Assembled gear gusset
|
Details
|
|
|
04-18-2021
|
1.00
|
Drilled & rivetted L angles to upper stop
|
|
|
|
03-21-2021
|
2.00
|
Debur drilled holes in firewall parts
|
|
|
|
|
03-14-2021
|
3.00
|
Fit & drill firewall parts
|
|
|
|
03-13-2021
|
3.00
|
Fit & drill firewall parts
|
|
|
|
|
02-28-2021
|
3.00
|
Debur parts for firewall
|
|
|
|
|
02-07-2021
|
1.00
|
Made stiffener for upper baggage floor
|
Details
|
|
|
02-07-2021
|
1.00
|
Drilled cabin floor holes to final size - pilot si
|
Details
|
|
|
02-06-2021
|
2.00
|
Drilled gear channel L and pilot seat base side su
|
|
|
|
02-02-2021
|
1.00
|
Drilled pilot seat base to baggage floor
|
|
|
|
01-31-2021
|
2.50
|
Drilled & installed L brackets for pilot seat base
|
|
|
|
01-16-2021
|
4.00
|
Drilled pilot seat base and supports
|
|
|
|
01-10-2021
|
2.00
|
Drilled cabin frame front gussets
|
|
|
|
01-09-2021
|
1.00
|
Drilled gear channel doublers - Pilot side
|
|
|
|
01-09-2021
|
1.00
|
Drilled cabin frame holes to final size
|
|
|
|
01-03-2021
|
3.00
|
Drill main gear strut fitting - Pilot side
|
|
|
|
01-02-2021
|
3.00
|
Drilled cabin floor holes to final size - Passenge
|
Details
|
|
|
01-01-2021
|
3.00
|
Drilled gear channel doublers - Passenger side
|
Details
|
|
|
12-27-2020
|
3.00
|
Drilled gear channel L and seat base side support
|
Details
|
|
|
12-24-2020
|
3.00
|
Fitted and pilot drilled cabin frame
|
Details
|
|
|
12-13-2020
|
1.50
|
Drill main gear strut fitting - Passenger side
|
Details
|
|
|
11-28-2020
|
3.00
|
Drilled seat base and supports
|
Details
|
|
|
11-27-2020
|
4.00
|
Worked on getting seat base to fit
|
Details
|
|
|
|
10-04-2020
|
3.00
|
Worked on passenger side seat area
|
Details
|
|
|
|
10-03-2020
|
2.00
|
Join rear & forward fuselage and drill longerons
|
|
|
|
|
09-19-2020
|
3.50
|
Installed rudder pedals
|
Details
|
|
|
09-07-2020
|
2.00
|
Worked on fitting passenger side seat base
|
Details
|
|
|
|
09-06-2020
|
2.00
|
Drill and cleco L brackets for cabin sides
|
Details
|
|
|
09-05-2020
|
3.00
|
Drilled Front Sliding Seat Supports
|
Details
|
|
|
09-05-2020
|
2.00
|
Clecoed Cabin Sides and Floor Stiffeners
|
Details
|
|
|
08-29-2020
|
5.00
|
Forward Fuselage Floor: Locate, debur, cleco
|
Details
|
|
|
|
08-23-2020
|
2.50
|
Riveted Baggage area
|
Details
|
|
|
08-21-2020
|
3.00
|
Re-assembled the baggage area
|
Details
|
|
|
08-21-2020
|
2.00
|
Drilled 2" holes in the Flaperon Control Covers
|
Details
|
|
|
08-21-2020
|
0.50
|
Doubled check cotter pins
|
Details
|
|
|
08-20-2020
|
1.00
|
Riveted everything I can at this point
|
Details
|
|
|
08-20-2020
|
1.00
|
Drilled & riveted 2 of 2 elevator cable bearings
|
Details
|
|
|
08-16-2020
|
1.00
|
Drilled & riveted 1 of 2 elevator cable bearings
|
Details
|
|
|
|
08-13-2020
|
2.00
|
Deburred & prepped steel parts for powder coating
|
Details
|
|
|
08-12-2020
|
1.50
|
Painted torque and elevator control tubes
|
Details
|
|
|
08-10-2020
|
1.50
|
Drilled & installed torque tube bearing
|
|
|
|
08-09-2020
|
2.00
|
Prepped torque and elevator control tubes for pain
|
Details
|
|
|
|
08-05-2020
|
1.00
|
Installed horizontal flaperon control rods
|
Details
|
|
|
08-02-2020
|
4.00
|
Drilled & clecoed F4-2, drilled & riveted F4-6
|
Details
|
|
|
07-31-2020
|
2.00
|
Cut & drilled : angles for right baggage floor pan
|
Details
|
|
|
07-28-2020
|
1.00
|
Cut & drilled L angles for left baggage floor pane
|
|
|
|
|
07-27-2020
|
1.00
|
Locate debur baggage floor and control tunnel part
|
Details
|
|
|
|
07-26-2020
|
2.00
|
Clecoed seat belt bracket and rear baggage ares
|
Details
|
|
|
07-25-2020
|
1.50
|
Riveted flap motor mount and control mixer assembl
|
|
|
|
07-25-2020
|
1.50
|
Installed flaperon bellcranks and flap motor
|
Details
|
|
|
07-21-2020
|
1.00
|
Drill holes in flaperon bellcrank bearings
|
Details
|
|
|
|
07-20-2020
|
1.00
|
Debur and drill flaperon bellcranks
|
Details
|
|
|
|
07-19-2020
|
1.00
|
Riveted Side Channel Doublers into place
|
|
|
|
07-19-2020
|
1.00
|
Installed L angles onto flaperon control covers
|
Details
|
|
|
07-18-2020
|
2.00
|
Continued work on baggage area
|
Details
|
|
|
07-12-2020
|
3.00
|
Worked on baggage floor and flaperon control cover
|
Details
|
|
|
07-06-2020
|
2.00
|
Drill Side Channel Doublers
|
Details
|
|
|
06-28-2020
|
1.00
|
Cleco flaperon mixer control tube into place
|
Details
|
|
|
06-21-2020
|
2.00
|
Drilled L brackets and riveted to baggage floor
|
Details
|
|
|
06-20-2020
|
2.00
|
Started on baggage floor
|
Details
|
|
|
|
06-20-2020
|
2.00
|
Assemble flaperon mixer bearing supports
|
Details
|
|
|
05-30-2020
|
5.00
|
Prep & paint flaperon control parts
|
Details
|
|
|
05-24-2020
|
1.50
|
Finished drilling flap motor bracket
|
Details
|
|
|
05-16-2020
|
3.00
|
Began drilling flap motor bracket
|
Details
|
|
|
04-19-2020
|
1.00
|
Rivetted baggage area back panel to fuse sides
|
Details
|
|
|
04-19-2020
|
1.50
|
Finished rivetting top skin
|
Details
|
|
|
04-18-2020
|
2.00
|
Rivetted wing attachment brackets
|
Details
|
|
|
04-18-2020
|
4.00
|
Put top skin on fuselage and began rivetting
|
Details
|
|
|
04-14-2020
|
1.50
|
Finished assembly of baggage area back panel
|
Details
|
|
|
04-12-2020
|
2.00
|
Worked on the baggage area back panel
|
Details
|
|
|
04-11-2020
|
3.00
|
Worked on the backend of the rear fuselage
|
Details
|
|
|
04-07-2020
|
1.50
|
Fix L brackets and finish riveting longerons to to
|
Details
|
|
|
04-05-2020
|
1.00
|
Installed rear wing attachments on top channel
|
|
|
|
04-05-2020
|
2.00
|
Began riveting longerons to top skin
|
Details
|
|
|
|
04-04-2020
|
2.50
|
Drill baggage back panel top bracket
|
Details
|
|
|
03-29-2020
|
2.00
|
Prepared baggage back panel for drilling
|
Details
|
|
|
03-28-2020
|
1.00
|
Trimmed front edge of bottom longerons
|
|
|
|
03-28-2020
|
1.50
|
Riveted bottom longerons to side skins
|
|
|
|
03-25-2020
|
2.00
|
Cut & shaped fuel header tank support tube
|
Details
|
|
|
03-21-2020
|
3.00
|
Cut & drill support for fuel header tank
|
Details
|
|
|
|
03-17-2020
|
1.50
|
Debur holes in H.T. attachment brackets & side fus
|
|
|
|
|
03-16-2020
|
2.50
|
Drill H.T. attachment bracket & fuselage skin (L
|
Details
|
|
|
03-14-2020
|
3.00
|
Drill H.T. attachment bracket & fuselage skin (R)
|
Details
|
|
|
03-01-2020
|
3.00
|
Clecoed rear fuselage together
|
Details
|
|
|
02-29-2020
|
1.00
|
Riveted rear fuselage top rail
|
Details
|
|
|
02-29-2020
|
2.00
|
Installed nut plates for the hell hole
|
Details
|
|
|
02-09-2020
|
2.00
|
Debur #11 holes in top skin, longerons, top rail,
|
Details
|
|
|
02-08-2020
|
4.00
|
Drill #11 holes in top skin, longerons, top rail,
|
Details
|
|
|
01-25-2020
|
7.00
|
Debur top skin and rivet L brackets
|
Details
|
|
|
01-23-2020
|
1.50
|
Rivet L's to left side rear skin
|
Details
|
|
|
01-18-2020
|
2.00
|
Rivet L's to right side rear skin
|
Details
|
|
|
01-18-2020
|
4.00
|
Debur left side rear skin & cleco L's
|
Details
|
|
|
|
01-17-2020
|
2.50
|
Cleco L's and longeron to right side rear skin
|
Details
|
|
|
01-11-2020
|
3.50
|
Debur right side rear fuelage skin
|
Details
|
|
|
01-10-2020
|
1.50
|
Debur right side rear fuselage skin
|
Details
|
|
|
|
01-09-2020
|
2.00
|
Rivet bottom skin longerons
|
Details
|
|
|
01-05-2020
|
3.00
|
Cleco'd longerons to bottom skin
|
Details
|
|
|
01-04-2020
|
3.50
|
Cleco'd L & Z brackets to bottom skin and riveted
|
|
|
|
01-01-2020
|
3.50
|
Finished deburring parts and applied Cortec
|
Details
|
|
|
12-28-2019
|
3.00
|
Continued deburring bottom fuselage parts
|
|
|
|
|
12-27-2019
|
3.00
|
Debur bottom fuselage skin and parts
|
Details
|
|
|
11-28-2019
|
2.50
|
Riveted skin and elevator into place
|
Details
|
|
|
11-23-2019
|
2.50
|
Drilled skin hinge line to final size
|
Details
|
|
|
|
11-16-2019
|
7.00
|
Trued up HS and cleco'd top skin
|
Details
|
|
|
11-02-2019
|
4.00
|
Installed new skin on bottom of stab
|
Details
|
|
|
10-26-2019
|
3.00
|
Positioned and drilled elevator hinge extentions
|
|
|
|
10-26-2019
|
1.00
|
Deburred new horizontal stab skin
|
Details
|
|
|
|
10-19-2019
|
4.00
|
Remove horizontal stab skin
|
Details
|
|
|
09-01-2019
|
2.00
|
Deburred fin skin and rivetted to skeleton
|
Details
|
|
|
08-31-2019
|
4.00
|
Assemble and rivet fin skeleton
|
Details
|
|
|
08-04-2019
|
1.50
|
Locate fin parts and begin deburring
|
|
|
|
|
07-04-2019
|
2.00
|
Mounted left nav lights
|
Details
|
|
|
06-25-2019
|
1.25
|
Finished drilling wing tip and installed access co
|
Details
|
|
|
06-23-2019
|
2.00
|
Fit and drill wing tip
|
Details
|
|
|
06-23-2019
|
1.00
|
Completed install of trailing edge
|
|
|
|
06-22-2019
|
2.00
|
Removed LL, tightened mounts, & re-installed
|
Details
|
|
|
|
06-22-2019
|
4.50
|
Fit and install trailing edge
|
Details
|
|
|
|
06-16-2019
|
2.00
|
Installed light assembly and secured wiring
|
Details
|
|
|
06-15-2019
|
1.50
|
Installed LL lens in wing
|
|
|
|
06-07-2019
|
2.00
|
Drilled lens and assembled lights
|
Details
|
|
|
06-02-2019
|
2.00
|
Trimmed LL lens
|
Details
|
|
|
|
05-27-2019
|
3.50
|
Trimmed LL lens and drilled mounting holes
|
Details
|
|
|
|
05-25-2019
|
2.00
|
Trimmed wing tip pieces
|
Details
|
|
|
05-05-2019
|
4.00
|
Drilled wing and light mounting bracket
|
Details
|
|
|
05-04-2019
|
5.50
|
Cut hole in wing for landing lights
|
Details
|
|
|
04-28-2019
|
2.50
|
Rough assembly of the landing lights
|
Details
|
|
|
04-13-2019
|
2.00
|
Riveted top wing skin over fuel tank
|
|
|
|
04-13-2019
|
1.50
|
Installed fuel tank & connected fuel lines
|
Details
|
|
|
03-30-2019
|
1.50
|
Prepared the other fuel access plate
|
Details
|
|
|
03-30-2019
|
4.50
|
Fitting of fuel tank into wing
|
Details
|
|
|
03-24-2019
|
1.50
|
Prepared one of the fuel access plates
|
Details
|
|
|
03-24-2019
|
1.50
|
Fuel tank leak test
|
Details
|
|
|
03-02-2019
|
7.00
|
Installed fuel sender & prepared for leak test
|
Details
|
|
|
02-23-2019
|
7.50
|
Riveted top wing skins
|
|
|
|
02-16-2019
|
3.00
|
Routed & secured wire and lines to rear spar
|
Details
|
|
|
02-16-2019
|
2.00
|
Hooked up pitot & static air lines
|
Details
|
|
|
02-09-2019
|
3.50
|
Worked on hoses: pitot tube, return fuel
|
Details
|
|
|
02-02-2019
|
6.00
|
Trailing edge, flaperon brackets, & pitot tube
|
Details
|
|
|
01-27-2019
|
2.50
|
Spent time studying landing light & pitot install
|
Details
|
|
|
|
01-26-2019
|
3.50
|
Complete deburring the skins and spar
|
|
|
|
01-20-2019
|
2.00
|
Installed wing tie down
|
Details
|
|
|
01-19-2019
|
5.00
|
Began deburring skins
|
|
|
|
|
01-13-2019
|
2.50
|
Finished drilling wing root top skins
|
Details
|
|
|
01-12-2019
|
6.00
|
Started drilling wing root top skins
|
Details
|
|
|
01-06-2019
|
3.50
|
Drilled spar line to final size and installed root
|
Details
|
|
|
01-05-2019
|
5.00
|
Clecoed top skins and #30 drilled spar line
|
Details
|
|
|
12-29-2018
|
4.50
|
Riveted bottom wing skins & install upper strut br
|
Details
|
|
|
12-29-2018
|
1.50
|
Made & installed strain relief for return fuel lin
|
Details
|
|
|
12-24-2018
|
3.50
|
Installed L brackets on top skin and deburred
|
Details
|
|
|
|
12-09-2018
|
3.00
|
Deburred & cortec bottom wing skins
|
Details
|
|
|
12-08-2018
|
5.00
|
Drilled upper strut fitting and deburred skins & s
|
Details
|
|
|
12-02-2018
|
4.00
|
Finished drilling along main spar
|
Details
|
|
|
12-01-2018
|
2.50
|
Began drilling along bottom main spar
|
Details
|
|
|
11-17-2018
|
3.00
|
Deburred and clecoed remaining bottom skins
|
Details
|
|
|
11-11-2018
|
2.50
|
Drilled, deburred, and riveted L brackets
|
Details
|
|
|
11-10-2018
|
5.00
|
Clecoed bottom skins and cut L brackets
|
Details
|
|
|
11-04-2018
|
1.50
|
Riveted rear spar to ribs
|
|
|
|
11-03-2018
|
4.00
|
Riveted ribs to main spar
|
Details
|
|
|
10-27-2018
|
5.00
|
Started on left wing skeleton
|
Details
|
|
|
10-21-2018
|
2.00
|
Wrapped and stored right wing
|
Details
|
|
|
10-21-2018
|
0.00
|
EAA Ford Trimotor at Rogers airport
|
Details
|
|
|
10-13-2018
|
1.50
|
Prepared and installed the other fual access plate
|
Details
|
|
|
10-06-2018
|
2.00
|
Installed nutplates on fuel access panel
|
Details
|
|
|
10-06-2018
|
3.00
|
Finished drilling & clecoing wing tip
|
|
|
|
09-29-2018
|
4.00
|
Mounted right wing tip nav light
|
Details
|
|
|
09-29-2018
|
2.00
|
Created strain relief and fitted front wing tip
|
Details
|
|
|
09-08-2018
|
5.00
|
Installed inboard trailing edge
|
Details
|
|
|
09-08-2018
|
1.00
|
Installed fuel sender wiring
|
Details
|
|
|
09-03-2018
|
5.00
|
Installed top wing skin over fuel tank
|
Details
|
|
|
08-18-2018
|
3.00
|
Installed Return fuel fittings and line
|
Details
|
|
|
08-18-2018
|
3.00
|
Installed Feed fuel fittings and line
|
Details
|
|
|
07-14-2018
|
1.50
|
Did some fitting of tank into wing
|
|
|
|
|
07-08-2018
|
1.00
|
Drained fuel test
|
Details
|
|
|
|
07-07-2018
|
2.00
|
Trimed wing tip pieces
|
|
|
|
07-07-2018
|
3.00
|
Fuel tank leak test
|
Details
|
|
|
07-04-2018
|
4.50
|
Installed fuel sender
|
Details
|
|
|
07-01-2018
|
1.00
|
Cut and bent fuel sender float arm
|
Details
|
|
|
06-30-2018
|
1.00
|
Prep'd fuel sender mounting ring
|
Details
|
|
|
06-24-2018
|
5.00
|
Drilled hole in tank for fuel sender
|
|
|
|
06-23-2018
|
3.00
|
Drilled hole in wing rib for fuel/vent return line
|
Details
|
|
|
06-16-2018
|
1.50
|
Fuel system planning & tank fit testing
|
|
|
|
|
06-09-2018
|
2.00
|
Removed rivets from top skin so I can install fuel
|
Details
|
|
|
06-02-2018
|
1.50
|
Riveted bottom trailing edge
|
Details
|
|
|
|
05-28-2018
|
5.00
|
Riveted top skins
|
Details
|
|
|
05-27-2018
|
3.50
|
Cleco'd top skins in place
|
Details
|
|
|
|
05-19-2018
|
2.00
|
Riveted L brackets to top skins
|
|
|
|
|
05-06-2018
|
4.00
|
Riveted flaperon brackets to wing
|
Details
|
|
|
04-28-2018
|
4.50
|
Drill & deburr leading edge rib holes
|
Details
|
|
|
|
04-26-2018
|
1.00
|
Deburr top wing skins and spar
|
|
|
|
|
04-23-2018
|
1.50
|
Deburr top wing skins and spar
|
|
|
|
|
04-22-2018
|
3.00
|
Deburr top wing skins and spar
|
|
|
|
|
04-21-2018
|
5.00
|
Remove and deburr top wing skins
|
|
|
|
|
04-08-2018
|
4.50
|
Began drilling root top wing skins
|
Details
|
|
|
04-07-2018
|
3.50
|
Finished drilling top wing skins
|
Details
|
|
|
04-06-2018
|
1.00
|
Drilled #30 holes top wing skins on spar
|
|
|
|
|
03-31-2018
|
5.00
|
Started drilling top wing skins
|
Details
|
|
|
03-30-2018
|
1.50
|
Finished riveting bottom wing skins
|
|
|
|
03-25-2018
|
6.00
|
Riveting bottom wing skins
|
Details
|
|
|
|
03-24-2018
|
7.00
|
Debur, Cortech, reassemble bottom wing skins
|
Details
|
|
|
03-18-2018
|
1.50
|
Debur wing skins and apply Cortec
|
|
|
|
|
03-17-2018
|
3.00
|
Debur wing skins and apply Cortec
|
|
|
|
|
03-05-2018
|
1.00
|
Drill bottom skins on spar to #20
|
|
|
|
|
03-03-2018
|
2.50
|
Drill bottom skins on spar to #30
|
Details
|
|
|
02-24-2018
|
2.00
|
Get wing spar level
|
|
|
|
|
02-17-2018
|
9.00
|
Installed bottom skins and brackets
|
Details
|
|
|
02-16-2018
|
4.50
|
Celco'd bottom skin. Cut L brackets.
|
Details
|
|
|
02-11-2018
|
5.50
|
Applied Cortec and riveted wing skeleton
|
|
|
|
02-10-2018
|
4.50
|
Installed spar tip. Drilled ribs for flaperons
|
|
|
|
02-08-2018
|
1.00
|
Drill and debur root rib
|
|
|
|
|
02-06-2018
|
2.00
|
Finished deburring & installing rear channel angle
|
|
|
|
02-05-2018
|
1.00
|
Debur rear channel angles
|
|
|
|
|
02-04-2018
|
4.00
|
Deburred more wing parts. Cleco'd the rear channel
|
|
|
|
02-03-2018
|
6.00
|
Installed root rib. Debur rear wing channels.
|
|
|
|
01-28-2018
|
3.50
|
Cleco'd wing ribs to main spar
|
|
|
|
01-27-2018
|
7.00
|
Finished drilling and deburring the wing ribs
|
|
|
|
01-20-2018
|
4.00
|
Drill and debur wing ribs
|
|
|
|
|
01-13-2018
|
3.00
|
Drill and debur wing ribs
|
|
|
|
|
01-07-2018
|
3.00
|
Drill and debur wing ribs
|
|
|
|
|
01-06-2018
|
3.00
|
Drill and debur wing ribs
|
|
|
|
|
01-01-2018
|
3.00
|
Locate and clean right wing components
|
Details
|
|
|
12-30-2017
|
0.50
|
Put fin away for later
|
Details
|
|
|
|
12-23-2017
|
2.50
|
Began assembling fin
|
Details
|
|
|
12-18-2017
|
1.00
|
Finished deburing. Applied anti-corrosion.
|
|
|
|
|
12-16-2017
|
3.00
|
Located parts and began deburring.
|
Details
|
|
|
12-09-2017
|
1.00
|
Clecoed elevator to stabilizer. Stored in barn.
|
|
|
|
12-04-2017
|
1.00
|
Completed elevator
|
Details
|
|
|
12-03-2017
|
4.00
|
Installed trim servo and attached to trim tab
|
|
|
|
11-26-2017
|
2.00
|
Completed riveting of elevator.
|
Details
|
|
|
11-25-2017
|
4.00
|
Riveted control arm assembly and safety wired hing
|
Details
|
|
|
11-12-2017
|
1.00
|
Started re-assembling elevator
|
|
|
|
|
11-10-2017
|
1.00
|
Applied anti-corrosion
|
|
|
|
|
11-05-2017
|
3.00
|
Disassemble and deburr parts
|
|
|
|
|
11-04-2017
|
5.00
|
Completed all cutting & drilling. Trim servo
|
Details
|
|
|
|
10-22-2017
|
1.00
|
Completed drilling elevator trim hinge
|
|
|
|
|
10-21-2017
|
4.00
|
Finished doulbers. Started on elevator trim hinge.
|
|
|
|
10-14-2017
|
3.00
|
Worked on installing doublers
|
|
|
|
10-01-2017
|
2.00
|
Completed drilling of elevator hinge
|
Details
|
|
|
09-30-2017
|
2.00
|
Fit elevator on H.S and begin drilling
|
|
|
|
09-24-2017
|
2.50
|
Completed stabilizer end caps
|
|
|
|
09-17-2017
|
1.00
|
Marking holes on stabilizer end caps
|
|
|
|
|
09-15-2017
|
2.00
|
Top skin riveted. Installed tip end ribs.
|
|
|
|
09-11-2017
|
1.00
|
Riveting top skin
|
|
|
|
|
09-08-2017
|
2.50
|
Finished deburring. Riveted doublers & brackets
|
|
|
|
09-04-2017
|
2.00
|
Finished drilling hinge holes. Started deburring h
|
|
|
|
|
09-03-2017
|
2.50
|
Drilling hinge holes
|
|
|
|
09-02-2017
|
6.50
|
Riveting horizontal stabilizer skin
|
Details
|
|
|
08-27-2017
|
1.00
|
Debur stabilizer skin
|
|
|
|
|
08-24-2017
|
1.50
|
Debur stabilizer skin
|
Details
|
|
|
08-21-2017
|
2.50
|
Cleco ribs and skin together
|
Details
|
|
|
08-20-2017
|
2.00
|
Deburring elevator ribs
|
|
|
|
|
08-14-2017
|
2.00
|
Began deburring
|
|
|
|
|
08-13-2017
|
0.50
|
Inspected stabilizer skin - Damaged
|
Details
|
|
|
|
08-12-2017
|
4.00
|
Riveted ribs to front & rear spar
|
|
|
|
08-11-2017
|
3.00
|
Assembled ribs with front & rear spars
|
Details
|
|
|
04-30-2017
|
0.00
|
Shop & garage flooded.
|
Details
|
|
|
|
04-25-2017
|
2.00
|
Applied cortec and riveted doublers to front spar
|
|
|
|
04-24-2017
|
1.00
|
Deburred front spar
|
|
|
|
|
04-23-2017
|
1.00
|
Riveted bottom doublers to rear spar
|
|
|
|
|
04-22-2017
|
3.00
|
Deburred and cleco'd rear spar
|
|
|
|
04-09-2017
|
5.00
|
Deburr stablizer parts
|
Details
|
|
|
12-11-2016
|
5.00
|
Brought kit home
|
|
|
|
12-09-2016
|
7.00
|
Built rudder at factory workshop
|
|
|
