Barry Motl - Experimental Aircraft Builder's Log

BARRY'S WEB SITE

Work Logs Found: 76

Category Work Time: 334 Hours

Date	Hours	Work Log Summary	Details
10-22-2002	3.00	installed prop


10-21-2002	3.00	cal. fuel tank senders


10-16-2002	4.00	hook airlons & flaps to push rods


10-15-2002	4.00	fit wings to plane


09-24-2002	8.00	Polished wing Installed flaps & ailerons


09-23-2002	3.00	Install radio & GPS units	Details


09-23-2002	5.00	Clean & polish bottoom side of wing


09-20-2002	3.00	Assemble Prop, Install Chute


09-19-2002	8.00	Install all lexan windows & doors


09-17-2002	2.00	installed port side window


09-13-2002	6.00	make up control panel


09-12-2002	6.00	Run wiring


09-11-2002	6.00	Safty wire, paint & splice wires


09-10-2002	8.00	Run wiring, hook brakes & engine control


09-09-2002	8.00	Run wiring & Control cables


09-06-2002	5.00	run chooke, & trottle & gas lines


09-05-2002	4.00	engine components


09-04-2002	8.00	Mount engine & hook up control cables


09-03-2002	8.00	Install rdder & horizontal stabilizer


08-30-2002	6.00	Paint fuselage	Details


08-29-2002	2.00	Etched Alum for painting


08-28-2002	10.00	Panit control surfaces & prep fuselage


08-26-2002	5.00	Spray poly brush & poly spray


08-15-2002	4.00	Shink fabric on control surfaces


08-14-2002	6.00	Covered control surfaces


08-13-2002	1.00	Started fabric covering control surfaces


08-12-2002	4.00	Install flap motor


08-07-2002	4.00	Glued control surfaces for fabric


08-05-2002	6.00	Bondo rivit lines


07-17-2002	3.00	Rivet trim to top of fuselage


07-08-2002	2.00	drilled out panel for switches & breaker


07-02-2002	2.00	Cut in compass & fit panel


07-01-2002	2.00	Install switches on stick


06-18-2002	4.00	Install vertical Stabilzer & Strobe


06-17-2002	3.00	Cover engine area & fit alum.


06-16-2002	6.00	cover inside of fuslage front area


06-15-2002	6.00	Fit lexan glass parts & drill holes


06-14-2002	3.00	cover inside fuselage


06-11-2002	6.00	Fit wing for 1st time	Details


06-10-2002	5.00	Install body to fuselage Install brakes


06-09-2002	3.00	Cover deck panel & install


06-06-2002	3.00	Cut instrument panel in


06-05-2002	3.00	fit panel deck cover


06-04-2002	3.00	Clean & sand parts to be fabric covered


06-02-2002	10.00	Fit fuselages body & more	Details


05-30-2002	3.00	Fitt trim tab servo motor


05-29-2002	4.00	Rivet tail boom to fuselage & file edges


05-28-2002	4.00	Cut & fit wing tips


05-23-2002	2.00	Fit vert. stabilizer & inspection plates


05-21-2002	2.00	Install tail boom & align stabilzer


05-20-2002	4.00	Install wing tip ribs & fit wing tips


05-18-2002	6.00	Installed top wing skins & set wash


05-16-2002	4.00	Fit tork tube & sand flaps-ailerons


05-15-2002	4.00	Glued & installed bottom wing skins


05-14-2002	4.00	Prepare skins for attachment


05-13-2002	4.00	Fit ailerons & flaps


05-09-2002	4.00	Install & fit flap & aileron hinges


05-08-2002	6.00	Prepare ribs & skins for glue & riveting


05-06-2002	4.00	Remove & deburr wing skin holes


05-05-2002	5.00	Fit top wing skins


05-02-2002	3.00	Cut & drill wing stiffeners


05-01-2002	3.00	Change ailerons tork tubes	Details


04-30-2002	4.00	Finished fitting bottom wing skins


04-29-2002	4.00	Fit bottom wing skins


04-10-2002	4.00	Rivet & install trim tab on stabilizer	Details


04-09-2002	3.00	Install aileron tork tube & clean boom


04-08-2002	5.00	Install rudder fittings


04-06-2002	4.00	Fit tail boom & horizontal stabilzer


04-04-2002	4.00	Rivet ailerons tork tubes


04-03-2002	8.00	Install tork tube, push rods & tail boom	Details


04-02-2002	8.00	Rivet ribs, flaps, ailerons & ass tires


04-01-2002	6.00	Installed ribs & box ribs onto D cell


03-31-2002	2.00	Drilled rivet holes into ribs


03-25-2002	1.00	Marked out rib spacing on wing D cell


03-13-2002	1.00	Kit arrived, unload plane


01-03-2002	0.50	Ordered Gull 2000

	SITE NAVIGATION

Contact Builder

Gull 2000 Home

Category		# Logs	# Hours

All		76	335

Empennage		49	202

Engine		6	33

Fuselage		9	47

Hardware		5	28

Interior		1	3

Kit		2	2

Systems		1	3

Wings		3	17