Powered By Kitlog Pro v2.0
Traci and Tom's RV-7A
RV-7A
Horz Stablizer
Work Logs Found:
45
Category Work Time:
54 Hours
Date
Hours
Work Log Summary
Details
08-05-2013
0.50
Horizontal stablizer completed!
Details
08-02-2013
0.50
Final horizontal stablizer rivets.
Details
08-01-2013
3.00
Skin HS601PP riveted to HS708 and rear spar.
Details
07-31-2013
1.50
Riveting the HS707 rib and a rivet fix.
Details
07-31-2013
2.00
Another challenge - fix for the mis-dimpled hole.
Details
07-30-2013
1.50
Just another priming day.
Details
07-29-2013
3.00
Finally riveting the HS-601PP skin to spar.
Details
07-25-2013
2.00
Riveting the ribs to the foreward spar.
Details
07-24-2013
2.00
Spar riveting - and more learning.
Details
07-23-2013
1.50
Rivet removal Horizontal Spar - Part II (Success!)
Details
07-23-2013
1.00
Priming the left horizontal skin - HS-601PP
Details
07-22-2013
1.00
Elevator hinges riveted to spar.
Details
07-22-2013
1.00
Education in Rivet removal.
Details
07-18-2013
1.50
Horizontal rear spar riveting.
Details
07-17-2013
1.00
The first rivets - horizontal stabilizer spar.
Details
07-10-2013
1.00
Just a lot more priming...
Details
06-25-2013
0.70
Cutting the rear spare notch.
Details
06-24-2013
2.00
Deburring, dimpling...oops.
Details
06-21-2013
2.00
Just another day of deburring - right H. sablizer
Details
06-20-2013
1.50
Same as before, but right side - 404/405 drilling
Details
06-19-2013
1.00
Dimpling - part 2
Details
06-18-2013
2.00
Deburr, drilling and dimples - part 1
Details
06-17-2013
0.70
Deburring holes and - oops.
Details
06-12-2013
1.00
Starting the right horizontal stabilizer.
Details
06-12-2013
1.50
Final HS-601PP to ribs holes.
Details
06-11-2013
0.50
Enlarging the HS405/404 and spar holes.
Details
06-11-2013
1.00
Drilling the HS405/404 to the spar
Details
06-07-2013
0.50
HR-405 drilling mistake? Time to ask!
Details
06-07-2013
0.50
Fluting and marking the HR-405 and HR-404
Details
06-07-2013
1.50
Fitting the HR-405 and 404 ribs and drilliing hole
Details
06-03-2013
1.50
Drilling ribs and putting skin on.
Details
05-29-2013
0.50
Fluting the horizontal stabilizer ribs.
Details
05-28-2013
1.00
Trim flanges of HS-405 ribs for spar fit.
Details
05-28-2013
0.20
Damage or just cosmetic?? (HS-405)
Details
05-28-2013
0.70
Countersink the HS-710 and HS-714 holes.
Details
05-23-2013
1.00
Six degrees of separation - bending spars
Details
05-23-2013
0.50
HS-702 bends - another 6 degree angle.
Details
05-23-2013
0.50
First dimple and set up countersink in HS-710 and
Details
05-23-2013
0.75
Cutting the bend strain relief in HS-702 spars.
Details
05-22-2013
2.00
Tapering the ends of the HS-710 and HS-714 spars.
Details
05-22-2013
1.00
Starting the forward spar
Details
05-22-2013
0.50
Marking the ends to round.
Details
05-22-2013
0.75
Center bearing assembly.
Details
05-21-2013
1.50
Rounding and smoothing.
Details
05-21-2013
1.50
Fitting spars and enlarging holes.
Details
SITE NAVIGATION
Contact Builder
RV-7A Home
Category
# Logs
# Hours
All
176
198
Horz Stablizer
45
54
Arrival
1
0
Elevator
59
65
Empennage
1
2
Firewall
3
3
Fuselage
2
3
Inventory
2
3
Rudder
36
34
Shop setup
5
10
Trim Tab
9
8
Vert Stabilizer
13
16
Copyright © 2001-2024 Matronics. All Rights Reserved.
