KitLog pro

Powered By Kitlog Pro v2.0

Ralph Finch RV-9A Build
Work Logs Found: 175
Category Work Time: 560 Hours
 Date
Hours
Work Log Summary

Details

 10-15-2014
1.00
Rivet remaining aft canopy sheet
Details

 09-28-2014
7.00
Mounts for ADSB and EMS modules
Details

 09-24-2014
1.00
Drilled/dimpled center holes for access hatch
Details

 09-21-2014
3.00
Finish forward access plate
Details

 09-10-2014
4.00
Made access hatch in upper forward skin
Details
     

 09-10-2014
1.00
Continued access hatch work.
Details

 07-16-2014
1.00
Finished riveting fuse side skin
Details

 07-09-2014
2.00
Canopy release mechanism
Details
     

 07-07-2014
0.50
Finished aft control bracket
Details

 07-06-2014
3.50
Control Brackets
Details

 02-24-2013
1.50
Installed antennas
Details
       

 10-14-2012
4.00
Attached fresh air inlets to fuse
Details

 08-11-2012
1.00
Riveted channel to cabin frame
Details

 07-26-2012
5.00
Riveted side rails
Details

 07-23-2012
6.00
Finished side rails
Details

 07-21-2012
3.00
Finished canopy rear hoop, started side rails
Details

 07-19-2012
5.00
Canopy frame shims, spacer blocks...
Details

 07-18-2012
5.00
Continue canopy frame
Details

 07-17-2012
6.00
Continue fitting canopy frame
Details

 07-16-2012
6.00
Continue fitting canopy frame
Details
       

 07-15-2012
3.00
Started adjustment of canopy frame/skin
Details

 07-14-2012
3.00
Started work on fwd canopy frame weldment
Details

 07-13-2012
1.00
More work on aft canopy latch
Details

 07-06-2012
4.00
Installed aft canopy latch
Details

 07-05-2012
3.00
Continue canopy work
Details

 07-04-2012
4.00
Finished side latch handle
Details
       

 07-03-2012
1.00
Made C-712
Details

 07-01-2012
5.00
Finished riveting fwd sub-assy to fuse, cut slots
Details
     

 06-30-2012
4.00
Continue riveting fwd sub-assy together
Details

 06-28-2012
1.00
Started riveting together fwd sub-assy
Details

 06-27-2012
3.50
Finished canopy release
Details
       

 06-25-2012
1.00
Continued adjusting canopy release linkage
Details

 06-24-2012
3.00
More work on canopy release
Details

 06-23-2012
4.00
Finished C-621 & -622 and WD-620
Details

 06-22-2012
4.00
Started making parts C-621 -622
Details
       

 06-20-2012
4.00
Deburred forward skin, started canopy build
Details

 06-18-2012
0.50
Riveted angles to fuselage
Details

 06-17-2012
6.00
Almost finished installing air vents
Details

 06-15-2012
2.00
Began install of air vents
Details

 06-13-2012
2.00
Riveted angles to fuse
Details

 06-11-2012
0.50
Riveted nutplates to angles
Details

 06-10-2012
5.50
Drilled and clecoed top fwd skin, fit angles
Details
       

 06-09-2012
1.50
Drilled and clecoed F-743B angle to F-643-1 channe
Details
       

 06-08-2012
1.50
Continue forward sub-assy install
Details

 06-07-2012
1.00
Riveted stub ribs to center panel
Details

 06-06-2012
2.50
Assembled fwd assy on fuselage
Details
       

 06-05-2012
1.50
Riveted L/R seal support angles, alodined large pa
Details

 06-03-2012
4.00
Continued fwd sub-assy
Details

 06-02-2012
4.00
Continued work on fwd sub-assy
Details

 05-31-2012
1.00
Prepped parts for Fwd Fuselage Sub-Assy
Details

 05-30-2012
5.00
Re-did F-703B angle, attached to instrument panel
Details
     

 05-29-2012
2.00
More angles, found mistake
Details

 05-28-2012
6.00
Began upper forward fuselage for tip-up
Details

 05-23-2012
1.00
Made, installed more interior clips
Details

 05-22-2012
1.50
Installed seat panel floors
Details
     

 05-20-2012
1.50
Added missing nutplates to left seat fuse ribs
Details

 05-19-2012
1.00
Added nutplates to right sidearm brace
Details

 05-18-2012
2.00
Screwed in seat panels, primed/painted braces
Details

 05-15-2012
1.00
Started placement of flap indicator
Details
       

 05-14-2012
0.50
Painted last panel, installed center baggage panel
Details

 05-13-2012
5.00
Misc items, see description
Details

 05-12-2012
4.00
Installed wear blocks for shoulder harness cables
Details
       

 05-11-2012
2.00
Finished top rivets
Details

 05-10-2012
1.00
Attempted top rivets
Details

 05-06-2012
4.00
Mostly riveted the area where the canopy frame bol
Details

 05-05-2012
2.00
Finished items to re-install baggage floors and F-
Details
       

 05-03-2012
1.00
"Fixed" fuselage dent
Details

 05-02-2012
5.00
Installed steps
Details
       

 05-01-2012
1.50
NOW finished canopy cabin frame
Details

 04-30-2012
3.00
Finished canopy cabin frame
Details
       

 04-29-2012
4.00
Bolted angles to fuse, started attaching frame
Details
       

 04-28-2012
4.00
Riveted angles and trimmed parts for tipup
Details

 04-27-2012
1.00
Match-drilled, cleaned and primed F-631C/D parts
     

 04-26-2012
1.00
Fit angles onto cabin frame assy
Details

 04-25-2012
5.00
Riveted cabin frame assy, made light holder
Details
       

 04-24-2012
1.00
Cleaned and primed cabin frame parts
Details
     

 04-23-2012
1.00
Counter-sunk all drilled holes on assy
Details

 04-22-2012
2.00
Finished basic cabin frame assy
Details

 04-20-2012
2.00
Continue with forward side of canopy cabin frame
Details
       

 04-19-2012
2.00
Continue canopy cabin frame
Details
       

 04-18-2012
1.00
More canopy cabin frame work
Details

 04-17-2012
1.00
Continued fitting outer strap
Details

 04-16-2012
6.00
Continued canopy cabin frame
Details
       

 04-15-2012
3.00
Canopy cabin frame
Details
     

 04-14-2012
2.00
Continue canopy cabin frame
Details

 04-12-2012
3.00
Made parts F-631C and F-631D
Details

 04-09-2012
1.00
Finished riveting aft skin
Details

 04-08-2012
4.00
Most rivets driven for aft skin
Details
       

 04-07-2012
4.00
Final prep before aft wing skin riveting
Details
       

 04-06-2012
6.00
Aft wing skin and tip-up cabin frame
Details

 04-04-2012
3.00
Drilled out pop rivets, dimpled skin
Details
     

 02-01-2012
4.00
Installed armrest braces, started aileron trim ins
Details
     

 01-29-2012
3.00
Finished armrest braces
Details
     

 01-28-2012
5.00
Made braces for armrests
Details
     

 12-31-2011
1.00
Made F-912D elevator stop
Details

 12-17-2011
2.00
Moved Adel clamps
Details
     

 12-14-2011
1.00
Riveted F-712E to F712, drilled holes in F712 for
Details

 12-11-2011
4.00
Tail light wire routing, tail tiedown
Details

 11-26-2011
2.00
Cut holes for Delta-Pop antennas
Details

 11-16-2011
2.00
Added more supports for electrical wiring
Details
       

 11-11-2011
3.00
Finished top skin reinforcement for ELT antenna
Details

 11-10-2011
4.00
ELT bracket and aft fuse skin
Details
       

 11-09-2011
4.00
Support frame for ELT
Details

 11-02-2011
4.00
Continued installation of static line
Details
       

 10-30-2011
2.50
Painted seat backs
Details

 10-29-2011
1.00
Added Adel clamps
Details

 10-26-2011
2.00
Added static ports
Details
       

 10-23-2011
3.00
Primed seat backs
Details

 10-21-2011
5.00
Strobe trays and ADAHRS tray
Details
       

 10-14-2011
2.00
Started tray for tail strobe pwr supply
Details
     

 10-14-2011
3.00
NOW I finished the ADAHRS tray
Details
     

 10-13-2011
1.00
Finished ADAHRS tray
Details
     

 10-12-2011
3.00
Continued work on ADAHRS tray
Details

 10-09-2011
2.00
Started ADAHRS tray
Details

 10-08-2011
1.00
Installed shoulder harness cables
Details

 09-25-2011
2.00
Deburred, cleaned, primed parts
Details
     

 09-18-2011
3.00
Painted fuselage parts
Details
       

 09-17-2011
4.00
More prep
Details

 09-16-2011
2.00
Continue prepping fuselage parts.

 09-15-2011
1.50
Continue preparing more sheet metal parts

 09-14-2011
2.00
Prep parts for painting
Details

 09-05-2011
4.00
Electrical routing
Details

 09-04-2011
2.50
Finish wiring placement for fuel pump
Details
       

 09-04-2011
2.50
Finish flap bar install
Details
       

 09-03-2011
2.00
Torque center section/landing gear bolts, touchup

 08-14-2011
5.00
Finished plumbing and covers
Details
       

 06-26-2011
4.00
Continue electric fuel pump cover
Details
       

 05-04-2011
2.50
Finished bolting landing gear weldments
Details

 05-02-2011
0.50
Installed some bolts on right landing gear weldmen

 05-01-2011
3.50
Finished torqueing plumbing fittings; bolted left
Details

 02-12-2011
2.00
2nd enamel paint coat
Details
     

 02-09-2011
2.00
Painted fuse interior
Details

 02-06-2011
4.50
More painting and prep
Details
       

 02-05-2011
5.00
Wash and prime
Details
       

 02-04-2011
1.00
Started adding a bracket
Details

 01-17-2011
2.00
Finished landing gear support install
Details

 01-15-2011
2.50
Continue installing landing gear supports
Details

 01-12-2011
2.50
Continue fitting landing gear supports
Details

 01-09-2011
5.00
Continue landing gear support install
Details
       

 01-08-2011
2.00
Continue landing gear support install
Details

 01-02-2011
4.00
Landing gear support
Details
       

 12-22-2010
20.00
Finished Center Section
Details
       

 12-01-2010
20.00
Finished floorboard install
Details
       

 09-01-2010
8.00
Continue adding nutplates to fuselage flooring
     

 08-29-2010
15.00
many tasks in one entry
Details
       

 07-30-2010
4.00
Fitting brake pedals into rudder pedals
Details

 07-25-2010
3.00
Continued installation of rudder pedal bracket
Details

 07-24-2010
2.00
Fit rudder pedal bracket, drilled holes to fuselag

 07-22-2010
1.00
Started rudder pedal assy into fuselage.
Details

 07-18-2010
4.00
Paint brake pedals
Details

 07-13-2010
2.00
Rivet brake pedal assys
Details

 07-12-2010
1.00
Countersunk brake plates
Details

 07-11-2010
4.00
Finish fitting brake pedals, reprimed
Details

 07-10-2010
4.00
Drilled and fitted support angles to brake pedals

 07-09-2010
1.00
Cut and deburred brake pedal angles (brackets)

 07-08-2010
1.00
Primed brake pedals and brackets with zinc chroma

 07-07-2010
4.00
Began flap parts, brake parts
Details

 06-26-2010
2.00
Finish steps
Details
     

 06-25-2010
3.00
Steps again
Details

 06-24-2010
2.00
Continue right step installation
Details

 06-23-2010
6.00
Right step
Details
     

 06-21-2010
2.00
Heat treated, cleaned and primed left step
Details
     

 06-20-2010
8.00
Left step
Details
       

 06-19-2010
6.00
Began left step installation

 06-14-2010
6.00
Finished seat back assys
Details
       

 06-13-2010
5.00
Seat back brace slot on fuse bulkhead
Details
       

 06-11-2010
4.00
Finished riveting seat backs
Details

 06-10-2010
1.00
Zinc-chromated right seat back
Details

 06-09-2010
4.00
Seat back priming and riveting
Details
     

 05-30-2010
6.00
Left seatback assy
Details

 05-29-2010
4.00
Seatback assy
Details
     

 05-28-2010
3.00
continue seat backs
Details

 05-22-2010
5.00
Continue seat backs
Details

 05-21-2010
4.00
Continue seat back
Details

 05-20-2010
1.50
Seat back braces
Details










Copyright © 2001-2024 Matronics. All Rights Reserved.