KitLog pro

Powered By Kitlog Pro v2.0

RV-8 N998W
Work Logs Found: 347
Category Work Time: 1237 Hours
 Date
Hours
Work Log Summary

Details

 04-08-2010
5.00
Edited max oil temp limit.
Details

 04-05-2010
5.00
Installed canopy latch set screw.
Details

 04-03-2010
5.00
Set engine limits in EFIS. Adjusted flap travel.
Details

 04-01-2010
5.00
Measured equipment arms.
Details

 03-31-2010
3.00
Finished installing fuel pump drain tube.
Details

 03-29-2010
6.00
Began installing empennage fairing.
Details

 03-28-2010
3.00
Finished installing and torquing spar bolts.
Details

 03-15-2010
2.00
A/C W&B completed. Brakes bleed.

 03-14-2010
4.00
Install spinner.
Details

 03-09-2010
6.00
Installed prop and trim servo connector.
Details

 03-03-2010
3.00
Installation on LH fuse tank bracket.

 03-02-2010
4.00
Flaps install & adjust. Work on LH tank bracket.

 03-01-2010
3.00
Installed RH tank bracket & vent line.

 02-28-2010
4.00
Fitting RH Fuse tank bracket & RH flap fairing.

 02-20-2010
6.00
Set wing sweep & insidence
Details

 02-19-2010
5.00
Set wing sweep & insidence

 02-18-2010
3.00
Set wing sweep & insidence

 02-08-2010
4.50
Installed empennage assembly

 02-04-2010
6.00
Installed empennage assembly

 02-03-2010
3.50
Installed empennage assembly

 02-01-2010
3.00
Installed empennage assembly

 01-26-2010
4.00
Preped & primed windscreen & forskin

 01-25-2010
3.00
Cleaned up wiring inside RH & reinstalled canopy.

 01-24-2010
4.00
Finisshed installing canopy latch & lock.
Details

 01-23-2010
4.00
Install canopy latch & lock.

 01-22-2010
2.00
Fabricate switch panel cover
Details

 01-21-2010
3.00
Continued windscreen detail sanding.
Details

 01-20-2010
4.00
Fairing finshing.
Details

 01-19-2010
3.00
Wheel pant, leg & intersection fairings finishing

 01-17-2010
4.00
Wheel pants, leg fairings installed

 01-14-2010
3.00
Continued windscreen prep and finish

 01-13-2010
1.00
Continued windscreen prep and finish

 01-12-2010
2.00
Finished sikaflex windscreen & LH skirt prep

 01-10-2010
3.00
Windscreen trim

 01-05-2010
1.80
Windscreen trim

 12-20-2009
1.00
Windscreen trim

 12-14-2009
4.00
Windscreen trim

 12-10-2009
1.00
Windscreen trim

 12-03-2009
1.00
Windscreen trim

 12-01-2009
6.00
Canopy windscreen prep.

 11-30-2009
5.00
Windscreen prep for epoxy.

 11-29-2009
1.50
Windscreen epoxy & dress

 11-28-2009
2.50
Windscreen fit & prep

 11-25-2009
1.20
Windscreen fit & prerp

 11-22-2009
2.50
Installed Alt static air port & A/S tube bulkhead

 11-21-2009
3.50
Canopy skirt prep & prime

 11-20-2009
6.10
Installed cowl hinge pin covers, Cowling prep for

 11-19-2009
6.20
Front bagage door adjust.

 11-18-2009
3.70
Wind screen fit, canop yskirt adjust.

 11-17-2009
3.00
Canopy skirt adjust & fit

 11-13-2009
4.00
Sanded canopy skirt

 11-12-2009
4.00
Wings & empenage to hangar.
Details

 11-09-2009
2.00
Cut & readjust rear canopy skirt

 11-07-2009
4.50
Skirt rived to frame & glassed in with micro.

 11-06-2009
3.00
Glue canopy skirt.

 11-05-2009
2.00
Continued canopy skirt fit.

 11-04-2009
4.70
Trim & adjust canopy skirt. Shorten front control

 11-03-2009
6.30
Contunued canopy skrit trim & fit.
Details

 11-01-2009
2.00
Canopy skirt trim and fit

 10-31-2009
2.00
Canopy skirt trim and fit

 10-30-2009
3.00
Canopy skirt trim and fit

 10-29-2009
2.00
Canopy skirt trim and fit

 10-26-2009
3.00
Trimmed and fit canopy skirts
     

 10-25-2009
3.00
Trimmed and fit canopy skirts
     

 10-22-2009
6.00
Trimmed and fit canopy skirts

 10-21-2009
5.50
Trimmed and fit canopy skirts
     

 10-19-2009
3.00
Started fitting right hand canopy skirt
       

 10-18-2009
1.00
Finished gluing spacer holes

 10-17-2009
6.60
Canopy prep and glue

 10-16-2009
2.20
And more canopy trimming

 10-14-2009
3.80
More canopy trimming

 10-13-2009
3.50
Canopy trimming

 10-12-2009
3.00
Cutting the canopy
       

 10-11-2009
2.70
More canopy trimming
       

 10-05-2009
3.00
Trimed canopy

 10-04-2009
2.00
Trimed canopy

 10-03-2009
3.30
Trimed canopy
     

 10-01-2009
1.30
Trimed canopy
     

 09-28-2009
4.00
Installed flexible brake lines on landing gear.
     

 09-21-2009
3.00
Re installed cowl hinges and pins.
       

 09-20-2009
2.00
Re installed cowl hinges and pins.
       

 08-15-2009
2.70
Epoxy & rivet cowl hinges.
Details

 08-14-2009
0.60
Epoxy & rivet cowl hinges.
Details
       

 08-13-2009
2.00
Fabricated aluminum backing strips for tip fairing
Details

 08-11-2009
2.50
Expoxy & rivet cowl hinges.

 08-09-2009
2.30
Expoxy & rivet cowl hinges.

 08-06-2009
2.50
Preped cowl hinges

 04-15-2009
2.40
Trimmed forward bag door. Installed Hall effect co
Details

 04-10-2009
3.60
Began installation of firewall blanket. Placed N#.
Details
     

 04-09-2009
1.40
Began firewall blanket fitting.
Details

 04-06-2009
1.80
Finished fabricating front spar angle F-862 L&R
       

 04-05-2009
2.00
Fabricate front spar angle F-862 L&R

 04-04-2009
1.50
Fabricate front spar angle F-862 L&R

 04-03-2009
1.50
Begin fabrication of F-862 L&R

 03-27-2009
3.80
Forward baggag door lock adjustment.
Details

 03-21-2009
3.00
Installed forward baggage door inner skin.
     

 03-19-2009
1.90
Ajust and fitforward baggage door

 03-18-2009
2.00
Forward baggage door fabrication & installation.

 03-16-2009
2.00
Forward baggage door fabrication & installation.

 03-15-2009
5.10
Forward baggage door fabrication & installation.

 03-14-2009
1.50
Refit and assemble Forward baggage door.

 03-12-2009
2.70
Refit and assemble Forward baggage door.

 03-11-2009
5.30
Finished riveting foreskin.
Details
       

 03-10-2009
4.00
Painted glareshield and mounted compass.
Details
       

 03-09-2009
3.00
Modified oil can stringer
       

 03-08-2009
3.90
Rived F-821PP innassembley
Details

 03-07-2009
3.80
Began rivetinf F-821PP in assembley.

 03-05-2009
5.80
Installed additional nutplates for the floor.
Details

 03-04-2009
2.50
Fabricated instrument panel access door modificati
Details

 03-03-2009
6.30
Fabricate and install baggfge door

 03-02-2009
3.30
Fabricate and install baggfge door

 03-01-2009
2.80
Fabricate and install baggfge door

 02-28-2009
4.00
Install pitot line from panel to LH wing root.
Details

 02-14-2009
2.00
Installed rear scat tube and fresh air vent.
     

 02-04-2009
3.00
Final fitting of forreskin and wiring.

 02-01-2009
3.00
Fit foreskin & removed instrument panel.

 11-23-2008
4.90
Reinstalled Fuel Pump.
Details

 11-22-2008
3.50
Reposition Fuel Pump bracket.

 11-16-2008
1.50
Canopy frame block installed.

 10-14-2008
1.50
Installed Lt inst panel attach bolt.
Details

 09-28-2008
2.70
Canopy side rails and frame installation.
     

 09-21-2008
1.80
Canopy side rails and frame installation.
     

 09-20-2008
2.30
Canopy side rails and frame installation.
     

 09-05-2008
4.00
Canopy side rails fabrication.
     

 09-04-2008
4.30
Canopy side rail fabrication

 09-03-2008
4.50
Canopy side rails fabrication.

 08-24-2008
4.00
Forward NACA vent fresh air vent scat tube install
Details

 08-24-2008
2.50
Aux fuel pump re assemble, Fuel valve re install.

 07-21-2007
2.50
Made firewall penitrations.
Details

 11-11-2006
4.00
Installed cowl hinges

 11-10-2006
2.70
Trimmed cowl

 11-09-2006
4.30
Finished trimming cowl and installed rear hinges.

 10-26-2006
5.90
Installed securing bolt for rear stick.
Details

 10-23-2006
2.80
Finished cut and fit upper cowl.
       

 10-22-2006
2.80
Fit top cowl to fuse.
       

 10-20-2006
1.50
Fiberglass patch cowl

 10-19-2006
3.30
Installed cowl hinges. Fixed mic jacks.

 10-17-2006
5.60
Trim cowl front and bevel cowl hing.
       

 10-16-2006
3.00
Removed Fuel Pump, refit fuel bulkhead fitting.
Details

 10-15-2006
2.60
Fixed cutting mistake.

 10-14-2006
4.10
Installed upper rear cowl hinge.
Details

 09-04-2006
5.00
Installed wheel farings.

 07-04-2006
4.50
Finished installing fuel vents.
Details

 07-03-2006
5.60
Install fuel & vent lines

 07-02-2006
2.30
Install fuel lines.

 07-01-2006
9.50
Finish install gear leg fairings.
Details

 06-29-2006
1.50
Install Gear leg fairings.

 06-28-2006
2.60
Installed gear leg fairings.

 06-27-2006
4.60
Installed brake lines,map lightsEngine mount washe

 06-20-2006
3.50
Installed axels,wheel pant brackets, brakes wheels
Details

 06-16-2006
2.00
Mounted tubes, tires and wheels

 06-06-2006
3.80
Attached gear legs to Fuelage.
       

 06-05-2006
1.20
Preped gear legs for assembly.

 06-02-2006
4.90
Riveted Top aft skin.

 03-08-2006
1.00
Debur, dimple & paint F-821

 03-05-2006
1.00
Debur & Dimple F-821

 02-24-2006
2.40
Fabricated ELT bracket.

 02-23-2006
7.00
Rear Seat back Assembly, ELT Bracket
Details

 02-14-2006
2.50
Rear seat back assembly.

 02-13-2006
4.10
Assembled front seat back.

 02-11-2006
2.40
Bolted/riveted to Fuse Wd808,F856,816,816B.

 02-10-2006
3.40
Bolted/riveted to fuse, Wd808,F856,816, 816B.

 02-02-2006
5.60
Fabricated F816Bs.
Details

 02-01-2006
2.50
Fit & assemble rear throttle, Fabricate F-816Bs.

 01-31-2006
3.30
Fit and assembled rear throttle.
     

 01-24-2006
1.50
Fabricate switch template.
     

 01-23-2006
3.10
Fit, drill and cleco in assembly F-816APP L&R side
Details

 01-20-2006
1.80
Fit F-816APP side rails in assembley.

 01-19-2006
2.50
Finished fastening FF-817L&R in place.
Details

 12-23-2005
4.00
Back drilled F-821 at left WD-802 left side.
Details

 12-22-2005
5.20
Drill and debur F-821.

 12-21-2005
5.00
Riveted F845L&R, 846L&R and 848L&R in assembly.
Details

 12-19-2005
5.50
Preped and assembled F803 instrument panel.

 12-15-2005
3.50
Assembled F821BPPs to F-866BPP & F801PP.
Details

 12-14-2005
1.50
Installed pitot static system in aft Fuselage.
Details

 12-11-2005
6.50
Fab & installed rear throttle
Details

 12-10-2005
5.10
Installed static system.
Details

 11-30-2005
4.00
Reinstalled gear box hardware, F866A&B.
Details

 11-21-2005
3.80
Finished gear box fasteners
Details

 11-20-2005
1.20
Inst Panel access door assembly.
     

 11-19-2005
5.00
Fabricated instrument panel access door.
       

 11-17-2005
2.00
Installed F861 landing gear cover plates.

 11-12-2005
7.00
Finish prep F867. Rivet F851s, 802k, 822.

 11-11-2005
3.50
Finished drilled F867, preped, primed, riveted ass

 11-10-2005
5.20
Installed front floor platenuts. Assembled F867 co

 11-04-2005
0.80
Assembled F867, Cooling Ramp.
       

 11-03-2005
7.50
Fab. Inst Access panel. riveted in assembleF802k,m

 11-02-2005
4.00
Fabricate instrument panel access door. Fwd Bag.

 10-27-2005
1.70
Debur, dimple F822,802K,M,836L&R.

 10-26-2005
4.20
Cleco & drill F803K&M, 835L7R, 850, 851.
Details

 10-25-2005
4.00
Finished gear alignment and drilled gear legs on.

 10-24-2005
3.00
Gear leg alignment. Instrument panel door dblr.

 10-01-2005
2.00
Drilled 7/16 hole in U804s & 806-1s. Bolted gear l

 09-30-2005
4.10
Finished F825.
Details

 09-29-2005
4.00
Finished deburing F825, Drilled F858's in assembly

 09-28-2005
2.30
Fabricated F858L&R, Debured & dimpled F825PP.

 09-27-2005
2.00
Finish drilled F825PP to assembly.

 09-26-2005
3.30
Drilled F825PP to fuselage.

 09-25-2005
3.50
Rudder stops installed, removed empenage, Riveted

 09-20-2005
4.00
Rig rudder peddles, cables. Installed rear hardwar

 09-18-2005
3.10
Rig elev, Mount V/S, rudder, cables & peddles.

 08-12-2005
2.00
Elevator rigging and..
Details
       

 07-24-2005
3.00
Elevator rigging

 07-23-2005
2.30
Began elevator rigging...

 07-20-2005
2.00
Mounted fuel pump....
Details

 07-06-2005
3.00
Fabricated, primed and assembled F-839..
Details

 07-05-2005
4.50
Fabricated, preped, primed and installed
Details

 06-30-2005
4.75
Drilled, rivetd and bolyted F-681 in ...
Details

 06-29-2005
5.00
Aligned and drilled in assembly...
Details

 06-16-2005
6.00
Drilled H/S to Fuse.. Installed hardware

 06-15-2005
5.00
Leveled and aligned fuse and H/S

 06-14-2005
4.00
Preped rudder peddle assmebly &
Details

 05-31-2005
1.50
Preped rudder peddle angles...
Details

 05-22-2005
2.20
Primed forwad seat ramp parts...
Details

 05-21-2005
2.30
Fit, drilled, deburred forward...
Details

 05-20-2005
2.70
Installed platenuts for midcabin covers.

 05-14-2005
5.70
Primed and re installed RH mid cabin...
Details

 05-13-2005
7.20
Installed RH mid cabin brace...
Details

 05-12-2005
2.30
Installed WD 813 weldments

 05-11-2005
1.60
Finished riveting F-802Cs

 05-10-2005
2.60
WD 813s drilled in place...
Details

 05-05-2005
1.80
Mounted platenuts on F865 brackets.

 05-02-2005
2.50
Started fabrication of new F-864PP....
Details

 05-01-2005
7.00
Finished mounting plantenuts for...
Details

 04-30-2005
2.00
Drilled deburred & clecoed platenuts...
Details

 04-29-2005
6.00
Drilled & Clecoed F-834&835 in assembly.
Details
       

 04-28-2005
2.00
Cut & fit rear bag shelf F834 & 835....
Details

 04-27-2005
1.00
Drilled and clecoed F804NPP MainSpar....
Details

 04-26-2005
5.00
Drilled, deburred,dimpled,primed...
Details

 04-25-2005
1.80
Install fwd baggage comp platenutes.
Details

 04-24-2005
2.50
Assembly of fws baggage compartment
Details

 04-23-2005
0.50
Riveted upper flap actuator doubler.
       

 04-10-2005
3.50
Fab upper flap actuator doubler
Details
     

 04-02-2005
2.50
Fabricated wood temp floor panels

 01-14-2005
2.60
Drill F864 in assembly.

 11-24-2004
2.00
Riveted Aft deck F819.
Details

 11-10-2004
4.00
Drilled F866 ABC in assembly
Details

 11-09-2004
3.30
Rivet arm rests. Install F837 plate nuts

 11-08-2004
5.30
Fit and checked flap actator mech.
Details

 10-21-2004
1.80
Fit and drilled inside side panels

 10-19-2004
6.10
Mount F837.
Details

 10-18-2004
7.20
Fab battery box mounting bracket.
Details

 10-17-2004
7.60
Finish installing floor plate nuts.
Details

 10-16-2004
3.20
Prep and install floor plate nuts.

 10-15-2004
3.00
Fab F833D-R hinge.
Details

 10-14-2004
3.50
Drilled floors and footwells to fuse.
Details
       

 10-07-2004
4.00
Preded floors and riveted stiffners.

 10-06-2004
3.80
Finished rear seat foot wells.

 10-05-2004
2.30

Details

 10-04-2004
2.60
Preped & riveted 810C&D,811L, 865 to 807
Details

 10-01-2004
5.20
Fabricate F805 B L&R, C, F L&R
Details

 09-30-2004
3.60
Rivet F820L.
Details
     

 09-29-2004
5.30
Rivet F820R & Gear Box. F802A&B (L&R)
Details

 09-28-2004
3.30
Fabricate F810C,811C,812B.
Details

 09-27-2004
4.60
Riveted left gear box in assmbly
     

 09-25-2004
0.50
Clecoed gear boxes to F820 L&R
     

 09-24-2004
12.00
Rivet F822, 823 L&R, 824, 826 & 827
     

 09-18-2004
3.40
Installed keeper rivetd on F844 L&R.
Details

 09-17-2004
2.50
Pro sealed F822 to firewall flange

 09-15-2004
1.40
Prime & prep F826, 827
Details

 09-10-2004
2.00
Prep F822, 826, 827 for riveting
     

 09-09-2004
3.40
Rivet F823L&R
       

 09-08-2004
3.10
Rivet F 823L&R
       

 09-07-2004
4.00
Prep F805LR, 806LR, 806LR for riveting

 09-02-2004
0.60
Prep F-823L

 09-01-2004
13.90
Finish rivet F824's L&R. Prep F823 L&R
Details
     

 08-27-2004
2.20
Rivet F824 L

 08-26-2004
3.50
Rivet F828 842. Cleco F824 L

 08-20-2004
8.40
Riveted skins F828 & F842 to fuse.

 08-07-2004
3.30
F824 L&R preped & primed, rolled edges

 07-30-2004
1.50
F842 preded & primed

 07-15-2004
2.30
WD409 nuts (AN365) torqued to 235 in #s
Details

 07-13-2004
3.20
Fuse rivet prep

 07-09-2004
2.10
Riveted F818L&R in place.
Details

 07-08-2004
3.00
Deburr, Dimple F824PPL & F842PP

 07-07-2004
3.20
Debur, dimple F824ppl & F842pp

 06-19-2004
2.00
Deburr, Dimple, countersink
Details

 06-18-2004
3.70
Deburr F-824L

 05-28-2004
4.10
Dimpling & Deburring
Details

 04-27-2004
1.00
Deburr F822PPL & Stringers

 03-17-2004
1.60
Finished drilled, dimple, deburr F823PP

 03-16-2004
5.80
Drill, Deburr, Dimple F822pp and F826pp
Details

 03-14-2004
3.70
RH Ger tower and skin prep

 03-13-2004
5.30
Primed LH skins and tower parts.
Details

 03-12-2004
4.60
Left landing gear sub assemblies prep
Details

 11-04-2003
0.60
Gear Towers R&R G L&R brackets.
       

 11-03-2003
3.40
Gear towers. R&R G L&R brackets

 10-26-2003
4.40
Remove and Replace WD822 L&R

 10-25-2003
6.30
Fit Gear towers.
Details
       

 10-20-2003
2.60
F802 assmeble

 10-19-2003
5.20
Install and drill in assembly F 802
Details

 10-18-2003
6.30
Preped and primed F802 ABCEF
Details

 10-17-2003
4.80
Finished drilling in assembly F802 ABC
Details

 06-02-2003
2.90
Remake F802 G rt

 05-20-2003
3.30
F802 A,B,C, E,F Assembly

 05-12-2003
3.00
F802 E,F,G,H
Details

 05-11-2003
3.70
F802 E,F, G,H
Details

 05-08-2003
3.80
Drilled in assembly F802 left. A,B,C,E,F

 05-07-2003
4.80
F802G & WD822L
Details

 04-30-2003
1.70
F802S - R
Details

 04-24-2003
3.60
F802A,B,C,E,F
Details

 04-23-2003
4.30
F802D&S
Details

 04-22-2003
6.75
Drilled skins
Details

 04-21-2003
2.00
Drilled F826 and F827 skins

 11-03-2002
1.50
Drilled F826 and F827 skins to assembly

 11-02-2002
6.50
Longerons, Seat brackets, Drilling
Details

 10-27-2002
7.60
Seat brackets & Skins
Details

 10-26-2002
5.70
Side skin & seat belt anchor
Details

 10-25-2002
2.00
Skins & longeron
Details

 10-24-2002
2.00
Bulkheads
Details

 10-23-2002
5.60
Skins & bulkheads
Details

 10-22-2002
5.80
Fuse skins
Details
       

 10-21-2002
7.00
Drilled skins to assembly
Details

 10-19-2002
1.50
Longerons and skins
Details

 10-18-2002
5.90
Tail spring mount, Longerons
Details

 10-17-2002
5.10
Floor skeleton
Details
     

 10-16-2002
4.40
Floor skeleton
Details

 10-15-2002
2.40
Longerons
Details

 10-14-2002
2.60
Cockpit floor area
Details

 10-13-2002
5.50
Cockpit floor area
Details

 10-11-2002
2.50
Cockpit floor area
Details

 10-10-2002
6.30
Cockpit floor area
Details

 10-06-2002
4.30
Cockpit floor area
Details

 10-05-2002
8.50
Cockpit floor area
Details

 10-04-2002
3.00
Cockpit floor area
Details

 10-03-2002
2.40
Cockpit floor area
Details

 10-02-2002
3.20
Cockpit floora area
Details

 09-30-2002
5.70
Cockpit floor area
Details

 09-29-2002
3.50
Cockpit floor area
Details

 09-28-2002
1.70
Cockpit floor area
Details

 09-27-2002
2.70
Cockpit floor area
Details

 09-25-2002
2.60
Cockpit floor area
Details

 09-24-2002
1.00
Cockpit floor area
Details

 09-23-2002
4.00
Cockpit floor area
Details

 09-22-2002
5.20
Cockpit floor area
Details

 02-17-2000
2.70
Cockpit floor area
Details

 02-16-2000
1.40
Cockpit floor area
Details

 02-09-2000
5.70
Cockpit floor area
Details

 02-01-2000
3.70
Bulkhead assembly
Details

 01-31-2000
4.00
Bulkhead prep
Details

 01-30-2000
4.20
Bulkhead prep
Details
     

 01-25-2000
4.50
Firewall components
Details

 01-23-2000
4.50
Firewall
Details

 01-17-2000
3.60
F-801 and components
Details

 01-16-2000
2.20
Fuselage jig
Details
       

 01-15-2000
6.60
Inventory
Details

 01-14-2000
8.00
Unpacked fuselage kit
Details










Copyright © 2001-2024 Matronics. All Rights Reserved.