Powered By Kitlog Pro v2.0
Neils Web Site
RV9A
Wings
Work Logs Found:
87
Category Work Time:
208 Hours
Date
Hours
Work Log Summary
Details
04-15-2019
5.00
Aileron Rigging
Details
04-12-2019
5.00
Aileron Rigging
Details
08-22-2016
2.50
Drill debur and rivet air seal - right side
Details
08-25-2015
1.00
Final fit left wing tip
Details
08-24-2015
1.50
Drill and dimple mounting holes in wings for tips
Details
08-21-2015
3.00
Rivet platenuts to left wingtip
Details
08-17-2015
2.00
Drill and dimple for recessed screws and rivets
Details
08-14-2015
3.00
Drill reinforcement strip and clecos to left Wing
Details
08-11-2015
1.50
Rivet left wingtip outside rib to wingtip
Details
08-11-2015
1.00
Drill left wingtip to left wing
Details
08-10-2015
1.50
Drill, cleco, debur, and prime left outside wing r
Details
08-03-2015
2.00
Rivet left inside wing tip rib to wing tip
Details
07-31-2015
2.00
Bond left inside wing tip rib to rib
Details
07-29-2015
4.00
Drill and fit left wing tip ribs into wing tip
Details
07-28-2015
1.00
Debur and prime left wingtip ribs
Details
07-24-2015
3.00
Trim left Wing Tip to fit
Details
02-02-2015
2.50
Rivet Plate Nuts to Right Wing tip
Details
01-28-2015
3.00
Bond attachment strip to inside of Wingtip
Details
01-26-2015
2.00
Drill Wing Tip for Plate nut attachment to Wing
Details
01-22-2015
2.00
Rivet right wingtip ribs to wingtip
Details
01-06-2015
1.00
Back drill wing tip rib after bonding
Details
01-05-2015
1.00
Bond wing tip rib to inside of right wing tip
Details
11-24-2014
4.00
Drilled and Cleco Right Wing tip to Wing
Details
10-14-2014
0.50
Drill Lightning holes in wing tip ribs
Details
09-30-2014
4.00
Fit Right Wingtip
Details
06-10-2013
1.50
Check Wing Sweep
Details
06-10-2013
1.50
Check Wing Plumb
Details
06-10-2013
2.00
Check Wing Incidence
Details
06-10-2013
1.00
Bolt left rear wing spar to Fuselage
Details
11-19-2012
5.00
Riveted Left lower wing skin
Details
11-16-2012
2.00
Started riveting right lower skin to wing
Details
11-16-2012
0.50
Ok to Close from EAA Technical Councelor
Details
11-16-2012
5.00
Closed Right Wing
Details
11-13-2012
2.00
Riveted access plates nut plates to lower wing ski
Details
11-12-2012
2.00
Prime inside of lower wing skins
Details
11-12-2012
1.00
Drill and dimple access covers for lower wing skin
Details
11-11-2012
1.50
Dimpled rib holes in lower wing skins
Details
11-09-2012
2.00
Dimpled right and left bottom wing skins
Details
11-08-2012
2.00
Dimple right wing ribs / Countersink rear spar
Details
10-26-2012
4.00
Cleco match drill and deburr right bottom skin
Details
10-25-2012
1.50
Dimple left wing ribs / Countersink rear spar
Details
10-23-2012
3.00
Completed installation of stall warner
Details
10-22-2012
2.50
Match drill left wing bottom skin, spar and ribs
10-22-2012
2.50
Assemble Stall warning sensor
Details
10-19-2012
3.00
Fit bottom skint to Left Wing
Details
10-17-2012
2.00
Cut slot in leading edge for stall warner
Details
10-16-2012
4.00
Stall Warner doubler
Details
10-15-2012
3.00
Ran conduit in right wing for lights and autopilot
Details
10-13-2012
3.00
Ran conduits in left wing for lights and autopilot
Details
10-11-2012
4.00
Pitot Tube
Details
10-10-2012
3.00
Attach Flaps to wings
Details
10-08-2012
5.00
Attach Ailerons to Wings
Details
10-05-2012
2.00
Primed Aileron push rods
Details
10-04-2012
1.50
Riveted rod ends to Aileron push rod
Details
10-03-2012
1.50
Primed inside of W-917 Aileron push rod
Details
10-03-2012
2.00
Install Aileron bell cranks
Details
10-01-2012
2.00
Match drilled Aileron push rod ends
Details
09-28-2012
1.00
Weld W-917 Aileron push rod threaded ends
Details
09-27-2012
4.00
Cut and Fit Aileron push rods (W-917 & W-918)
Details
09-25-2012
3.00
Drill and attache Aileron hinge brackets
Details
09-24-2012
3.00
Cut and install landing light lens
09-18-2012
5.00
Cleco, match drill, dimple, rivet Aileron fairings
Details
09-17-2012
2.00
Rivet Flap gap fairings to wings
Details
09-14-2012
2.00
Rivet right Flap fairing to rear spar and upper sk
Details
09-14-2012
1.50
Dimple upper Wing skins for Flap fairing
Details
09-14-2012
1.00
Dimple Flap fairings
09-14-2012
1.00
Cleco left and right Flap fairing to wings
Details
09-13-2012
1.00
Match drill flap fairings
Details
09-13-2012
1.00
Install assembled landing ling assembly in wing
Details
09-12-2012
2.00
Modify landing light brack and install balast and
Details
09-10-2012
2.50
Drill and rivet Landing Light brackets Plate Nuts
Details
08-23-2012
1.50
Fit and drill Landing Light retainer strips
Details
08-23-2012
2.00
Deburr and cleco Flap gap fairings to Wings
Details
08-22-2012
3.00
Cut hole in left Wing for landing light
Details
08-21-2012
2.00
Pressure test fuel tanks
Details
08-15-2012
2.50
Seal Fuel Tank Access Plate
Details
08-13-2012
3.00
Riveted Aileron brackers to rear wing spars
Details
08-10-2012
1.00
Cleco Aileron Brackets to rear Wing spars
08-09-2012
4.00
Fabricated Aileron brackets
Details
08-07-2012
3.00
Bend fuel sender floats and test
Details
08-06-2012
3.00
Tie down Rings
Details
08-03-2012
1.50
Seal fuel level sendier to cover plate
Details
08-03-2012
2.00
Fuel Tank Z brackets
Details
08-02-2012
2.50
Fuel pickup Tiubes
Details
07-26-2012
3.00
Mounted Wings on Stand
Details
07-25-2012
4.00
Constructed Wing Stands
Details
07-24-2012
3.00
Unpack Quick Build Wings
Details
SITE NAVIGATION
Contact Builder
EX-3 Home
RV9A Home
Category
# Logs
# Hours
All
853
3355
Avionics
106
456
DAR and Technical Co
6
12
Delivery & Invenory
3
23
Empennage
121
306
Engine
22
82
Finish
186
758
Firewall Forward
139
508
Fuselage
178
700
Miscellaneous
3
10
None
2
40
Wings
87
460
Copyright © 2001-2024 Matronics. All Rights Reserved.
