Powered By Kitlog Pro v2.0
Mitch Hodges (N601MH)
Zodiac 601HDS
All
Work Logs Found:
147
Category Work Time:
160 Hours
Date
Hours
Work Log Summary
Details
09-13-2009
1.50
Remark LE skin for VR8
Details
09-13-2009
0.50
Photo inside of LE Skin for Error
Details
09-10-2009
0.10
Factory Call
Details
04-13-2008
0.20
Drill Pilot Holes For Leading Edge Skin
Details
04-12-2008
0.50
Review Nose Skin
Details
04-12-2008
0.60
Mark Nose Ribs On Nose Skin
Details
04-10-2008
0.75
Mark Nose Rib Rivet Lines
Details
04-10-2008
3.00
Mark and Trim Spar Line on Nose Skin
Details
04-10-2008
0.00
Additional Photos of Router Process
Details
04-09-2008
1.00
Mark Spar Line and Fit Nose Skin
Details
04-08-2008
0.90
Zinc Oxide and attach bottom of nose skin
Details
02-02-2008
3.00
Attach Bottom of Nose Skin To Ribs/Spar
Details
01-26-2008
1.00
Prepare Leading Edge Nose Skin
Details
01-19-2008
0.50
Add Tack Rivets to Spar
Details
01-17-2008
0.25
Rivet Bottom Skin
Details
01-14-2008
0.50
Realign and cleco bottom rear skin.
Details
01-12-2008
0.25
Attache L's to skin
Details
06-03-2007
2.25
Work on bottom rear skin
Details
05-29-2007
0.15
Shape L's for False Ribs
Details
05-29-2007
0.25
Make False Rib L Angle
Details
05-29-2007
1.10
Clamp and drill skin
Details
05-29-2007
0.90
Add L at 8.5 to replace locker
Details
05-28-2007
0.50
Rivet Skin
Details
05-28-2007
0.50
Make supports for wire conduit and attach
Details
05-28-2007
0.75
Add Tip Rib
Details
05-27-2007
1.25
Zinc Oxide, Debur, attach top rear wing skin
Details
04-29-2007
3.25
Build Wing Skeleton
Details
04-21-2007
0.75
Zinc Chromate Left O/B Wing Skeleton
Details
04-14-2007
2.50
Duct Tape Method for Nose and Rear Ribs
Details
04-13-2007
1.50
Prepare Nose Ribs for LE Tanks
Details
04-11-2007
1.50
Drill Rear Z and add L angle to spar
Details
04-10-2007
1.00
Start Left Outboard Wing
Details
04-04-2007
3.00
Discover major aileron mistake!
Details
04-14-2006
0.05
Wing Skeleton Ready to Proceed
Details
04-06-2006
0.25
Aileron Horn Template
Details
04-05-2006
1.00
Trim I/B Wing Skins
Details
04-02-2006
1.50
Add Aileron Tip
Details
04-01-2006
1.00
Trim AIleron Length
Details
03-19-2006
0.75
Trim Aileron Tip
Details
03-18-2006
0.75
Cut Aileron to Length
Details
03-12-2006
0.75
Complete Wing!
Details
03-12-2006
0.75
Clean and mark right aileron
Details
03-11-2006
0.75
Run Rivets for Tip Rib
Details
03-10-2006
0.25
Attach L6 to top rear wing skin
02-19-2006
2.00
Trim for New Nose Rib and Mark Pilot Holes
Details
02-19-2006
3.00
Complete Tip Rib Drilling and Fitting
Details
02-18-2006
0.75
New tip rib arrives!
Details
02-18-2006
0.40
Add Tie Down Ring
Details
02-12-2006
2.40
Trim O/B Skins
Details
02-11-2006
1.00
Trim outer wing skin
Details
02-11-2006
2.40
Close Nose Skin
Details
02-09-2006
1.00
Attach Fuel Line, debur nose skin
Details
02-06-2006
0.25
Bracket for fuel line
Details
02-05-2006
0.75
Complete Tank installation
Details
01-29-2006
1.00
Grounding for Tank
Details
01-28-2006
0.50
Tank Inlet Installations
Details
07-04-2005
2.00
Drill Hole and Attach Sender
Details
05-28-2005
0.50
Uncleco and Debur skin
Details
05-28-2005
0.50
Make Template for Fuel Inlet
Details
05-28-2005
2.00
Cut Filler Hole in LE skin
Details
05-01-2005
1.45
Drill A5 Line for Nose and Spar line
Details
05-01-2005
0.55
Continue to work on Sender
Details
04-24-2005
1.00
Bend Sending unit for wing
Details
04-16-2005
0.10
Sun and Fun Discussion with Zenith
Details
04-10-2005
0.50
Test fit the tank
Details
04-10-2005
0.50
Make template for tank bottom holes
Details
04-10-2005
0.15
Make Drill Board to support skin
Details
04-10-2005
0.60
Drill holes in bottom of wing
Details
04-10-2005
0.45
Drill Fuel Outlet Hole
Details
04-10-2005
0.50
Draw plans for Sender
Details
04-09-2005
0.75
Trim Spar end of LE Skin
Details
04-09-2005
0.90
Prep Fuel Tank
Details
04-09-2005
0.60
Make Template for fuel outlet
Details
04-09-2005
1.25
Drill Pilot Holes on LE Upper Spar
Details
04-08-2005
1.00
Practice cuts to trim LE skin
Details
04-08-2005
0.25
Mark Top LE Skin to Cut
Details
04-08-2005
1.25
Drill Pilot Holes
Details
04-08-2005
2.40
Drill and Cleco LE skin to ribs
Details
04-08-2005
1.45
Bend and mark LE Skin
Details
04-07-2005
0.17
Zinc Oxide LE Skin and U Channel
04-07-2005
0.75
Rivet Bottom LE Skin to Spar/Nose Ribs
Details
04-07-2005
0.50
Remove Skin and Wash
Details
04-07-2005
0.10
Ready Bottom of LE Skin for Riviting
Details
04-07-2005
0.90
Make LE Tank U Channel
Details
04-07-2005
0.15
Attach U-Channel
03-20-2005
0.01
Recieved U Channel from Zenith
Details
03-18-2005
1.45
Reattach Nose Skin to check end
Details
03-18-2005
0.10
Contact Zenith About U Channel
Details
03-17-2005
1.00
Remove and Debur Skin
Details
03-14-2005
1.40
Drill Rivet Lines Bottom Leading Edgr
Details
03-13-2005
1.75
Mark and Drill Pilot Holes Leading Edge
Details
03-11-2005
0.50
Mark Rivet Locations on leading Edge
Details
03-11-2005
4.00
Mark Leading Edge for Rivet Lines
Details
02-08-2005
0.25
Attach Fuel Line Bracket
Details
04-12-2003
0.25
Take photos of the wing at current stage
04-11-2003
1.50
Support and mark nose skins
Details
11-26-2002
1.00
Steps 21a - c: Leading Edge Nose Skin
Details
11-17-2002
3.00
Step 19-20: Rivet Rear Bottom Skin
Details
11-16-2002
1.00
Wing Locker Channel
Details
11-03-2002
0.25
Remove Bottom Skin
Details
10-27-2002
1.00
Complete work on Conduit L's
Details
10-26-2002
0.50
L Brackets for Wire Conduit
Details
10-26-2002
1.50
Bottom Skin Wing Locker Channel
Details
10-19-2002
2.00
Install Wing Locker Channel
Details
10-14-2002
0.01
Response from Zenith on Wing Lockers
Details
10-05-2002
0.90
Prepare Rear Bottom Skin for Attachment
Details
09-21-2002
1.00
Step 17: Position Bottom Skin
Details
09-21-2002
0.34
Step 17: Wings Supports Complete
Details
09-21-2002
1.27
Step 16: Prepare L angles for False Ribs
Details
09-20-2002
0.50
Step 17: Make wing supports
Details
09-20-2002
1.25
Step 15: Install Top Rear Wing Skin
Details
09-20-2002
1.00
Review plans for Wing Locker
Details
09-20-2002
1.00
Recleco Top Rear Skin
Details
08-31-2002
2.00
Prepare Top Rear Skin for Attachment
Details
08-03-2002
0.09
Countersink for Tack Rivets
Details
07-04-2002
1.00
Straighten Rear Skin
Details
07-04-2002
0.25
Step 14. Tack Rivets
Details
07-04-2002
0.50
L Angles between Rib stations
Details
06-28-2002
1.25
Position the Rear Top Skin 6SV3-5
Details
06-28-2002
0.25
Place supports under training edge
Details
06-28-2002
0.75
Drill Top Rear Skin for Rivets
Details
06-27-2002
0.25
Crimp L angles (False Ribs)
Details
05-27-1999
0.50
Wing Skins
Details
05-25-1999
1.25
End Ribs
Details
05-20-1999
2.15
Finish up Right Outboard Wing skeleton
Details
05-13-1999
1.90
Nose Ribs continued
Details
04-30-1999
0.45
More Ribs
Details
04-21-1999
1.25
Prep for LE Tank
Details
04-20-1999
2.25
Inventory Wing Tanks/Rib Prep
Details
02-28-1999
0.75
Debur and attach ribs and spar
Details
02-21-1999
2.50
Continue work on rear ribs
Details
01-24-1999
2.60
Complete wing tip, begin Nose Rib work
Details
01-20-1999
0.75
Marked Nose Ribs/Wing Tip
Details
12-13-1997
1.50
Debur, check and Rivet Left Aileron
Details
12-01-1997
1.50
Left Aileron work continues
Details
11-30-1997
2.00
Continued work on Left Ailerons
Details
11-25-1997
0.50
Left Aileron Ribs marking
Details
11-25-1997
2.25
Correct Aileron twist in Right Aileron
Details
09-07-1997
2.00
Drill and Rivet the Right Aileron
Details
08-25-1997
0.50
Mark and predrill right Aileron Ribs
Details
08-25-1997
0.10
Cut O/B end of the Rear Zee at 45 deg
Details
08-11-1997
1.00
Pre-drill Rear Zee 6SV4-2 for Rear Ribs
Details
08-05-1997
0.50
Cleco Rear O/B Splice Plate to Rear Zee
Details
06-08-1997
4.00
Skinning the Rudder
Details
06-08-1997
1.00
Rudder Completed!
Details
06-07-1997
4.00
Rudder Workshop
Details
06-07-1997
4.50
Build Rudder Skeleton
Details
SITE NAVIGATION
Contact Builder
Zodiac 601HDS Home
Category
# Logs
# Hours
All
147
160
Ailerons
8
11
Rudder
4
14
Wings
135
135
Copyright © 2001-2024 Matronics. All Rights Reserved.
