KitLog pro

Powered By Kitlog Pro v2.0

Dan's Web Site
Work Logs Found: 134
Category Work Time: 110 Hours
 Date
Hours
Work Log Summary

Details

 12-19-2009
1.00
Secure Right Baffle Cylinder Fin Wraps
Details
       

 12-19-2009
1.00
Secure Left Baffle Cylinder Fin Wraps
Details
       

 12-19-2009
1.00
Replace Lower Oil Cooler Fitting with 45
Details
       

 12-19-2009
1.00
Install and Safety Wire Oil Cooler Support Rod
Details
       

 12-07-2009
1.00
Reinstall Baffles and Oil Cooler
Details
     

 12-05-2009
0.50
Install Baffle Material with Screws
Details
     

 12-04-2009
1.00
Install Baffle Material with Screws
Details
       

 12-01-2009
2.00
Remove Baffles and Drill Out Pop Rivets
Details
       

 12-01-2009
0.50
Drill Hex Oil Cooler Brace for Safety Wire
Details
     

 11-30-2009
1.00
Replace Pop Rivets with Screws - Left Front
Details
       

 10-06-2009
2.00
Trim, Punch, Drill, Rivet Final Airseal Strips - F
Details
       

 09-19-2009
0.50
Trim & Punch Right Front Airseal Fabric Strip
Details
       

 09-19-2009
0.50
Trim & Punch Left Front Airseal Fabric Strip
Details
       

 09-09-2009
0.50
Trim & Punch Left Side (Middle) Airseal Fabric Str
Details
       

 09-09-2009
0.50
Rivet Airseal Fabric to Left Side (Middle) Baffle
Details
     

 09-09-2009
0.25
Reinstall Top Cowl; Check Baffle Contours - Right
Details
       

 09-09-2009
0.25
Reinstall Top Cowl; Check Baffle Contours - Left
Details
       

 09-09-2009
0.00
Photo Op: Front Baffles Marked for Final Trimming
Details
       

 09-09-2009
0.50
Mark Front Baffles for Further Trimming
Details
       

 09-09-2009
1.00
Install Right Side (Middle) Airseal Strip
Details
     

 09-09-2009
1.00
Install Right Side (Front) Airseal Strip
Details
     

 09-09-2009
1.00
Install Left Side (Front) Airseal Strip
Details
     

 09-09-2009
1.50
Final Trim Front Baffles
Details
       

 08-31-2009
0.50
Trim & Punch Right Side (Aft) Airseal Fabric Strip
Details
       

 08-31-2009
0.50
Rivet Airseal Fabric to Right Side (Aft) Baffle
Details
     

 08-28-2009
0.50
Trim & Punch Left Side (Aft) Airseal Fabric Strip
Details
       

 08-28-2009
0.50
Trim & Punch Left Aft Airseal Fabric Strip
Details
       

 08-28-2009
0.50
Rivet Airseal Fabric to Left Side (Aft) Baffle
Details
       

 08-28-2009
0.50
Rivet Airseal Fabric to Left Aft Baffle
Details
       

 08-27-2009
1.00
Trim & Punch Right Aft Airseal Fabric Strip
Details
       

 08-27-2009
0.50
Rivet Airseal Fabric to Right Aft Baffle
Details
       

 08-27-2009
0.25
Install Mag Cooling Blast Tubes
Details
       

 08-27-2009
0.50
Install Cover Plate/Airseal Fab over Manifold Pres
Details
       

 08-27-2009
1.00
Final Install Right Baffles; Fab Manifold Cover Pl
Details
       

 08-27-2009
0.25
Bolt Baffles to Center Braces; Add Oil Cooler Brac
Details
       

 08-26-2009
1.50
Final Install Left Baffles & Oil Cooler
Details
       

 08-25-2009
0.50
Final Rivet Front Baffles - Cyl Fin Wrap Plates
Details
       

 08-25-2009
1.00
Final Rivet Back Baffles - Cyl Fin Wrap Plates
Details
       

 05-12-2009
1.00
Fabricate Oil Cooler Support Brackets / Rod
Details
       

 05-11-2009
2.00
Final Trim Back Left Baffles; Reinf Flanges; Cap
Details
     

 05-11-2009
1.00
Fabricate and Drill Retention Clips
Details
       

 05-05-2009
3.00
Final Trim Front Baffles; Reinf Flanges
Details
       

 05-04-2009
2.00
Final Trim Right Aft Corner Baffles; Reinf Screw H
Details
     

 05-03-2009
1.00
Remaining Baffles - Mark Top Edges for Final Trim
Details
       

 05-03-2009
0.25
Install Lower Cowl
Details
     

 05-03-2009
0.50
Front Baffles - Mark Top Edges for Final Trim
Details
       

 05-03-2009
0.25
Drill Mounting Holes for Harness Grommets
Details
       

 05-03-2009
0.25
Drill Hole For Alternator Blast Tube
Details
     

 05-03-2009
0.50
Connect the Dots to Mark the Final Trim Lines
Details
     

 04-04-2009
0.75
Parts 5&6 - Cutouts for Harness, Blast Tube
Details
     

 04-04-2009
1.00
Part 7 - Cutouts for Cabin Heat, Harness, Blast Tu
Details
       

 04-04-2009
0.25
Match Drill Cabin Heat Inlet Flange to Part 7
Details
       

 03-17-2009
1.00
Trim, Drill, Debur, Bolt Part 12 to Engine & Parts
Details
       

 03-16-2009
1.00
Rivet Part 7 to Part 8 Reinforcement Angles
Details
       

 03-16-2009
1.00
Cut Flanges Off Part 8; Fabricate Angle Replacemen
Details
       

 03-16-2009
1.00
Countersink, Debur, Alodine, Rivet Angles to Part
Details
       

 02-25-2009
1.00
Install Parts 4,5&6, Clamp and Drill 5&6 Together
Details
       

 02-25-2009
1.00
Countersink, Debur, Clean, Alodine Rivet Parts 5&6
Details
       

 02-24-2009
1.00
Bend, Drill, Debur, Alodine, Install Part 15
Details
       

 02-23-2009
0.50
Rivet Mounting Spacer to Part 6
Details
       

 02-23-2009
0.50
Install Part 6 on Engine
Details
       

 02-23-2009
1.00
Fabricate Mounting Spacer for Part 6
Details
       

 01-19-2009
1.00
Install Parts 4&5 and Oil Cooler
Details
       

 01-19-2009
1.00
Debur, Clean, Alodine, Rivet Parts 4&5
Details
       

 01-19-2009
0.50
Cut Flange Off Part 8; Fabricate Angle Instead
Details
       

 01-19-2009
0.50
Countersink Parts 4 and 5
Details
       

 01-18-2009
0.50
Match Drill Parts 4 & 5 & Reinforcement Components
Details
       

 01-18-2009
1.00
Fabricate and Drill Part 4 Brace Angle / Spacer
Details
       

 01-18-2009
0.50
Drill Oil Cooler Mounting Holes in Aft Baffle/Doub
Details
     

 01-18-2009
1.00
Align Drill Parts 4 & 5 & Reinforcement Components
Details
       

 01-17-2009
0.25
Trim Top of #3 Baffle; Install Cowl
Details
     

 01-17-2009
0.25
Trial Fit Cowl Halves - Edges Line Up Nicely
Details
       

 01-17-2009
2.00
Position & Drill FF-709 Oil Cooler Doubler to Part
Details
       

 01-17-2009
1.25
Mark 3/8" Down From Top of Paper Clips & Trim
Details
       

 01-17-2009
0.25
Install Paper Clips on Top Edges of Baffles
Details
       

 01-13-2009
0.50
Third Iteration of Trimming Top Bulkhead Edges
Details
       

 01-13-2009
0.50
Second Iteration of Trimming Top Bulkhead Edges
Details
       

 01-13-2009
0.50
Mark Front of Left Side Baffle for Trimming
Details
       

 01-12-2009
1.00
Trim New Left Aft Baffle Parts 4 & 5
Details
       

 01-12-2009
1.00
First Iteration of Trimming Top Bulkhead Edges
Details
       

 01-10-2009
0.50
Trim/Fabricate Part 13 - Left Inlet Floor Support
Details
       

 01-10-2009
0.50
Rivet Right Inlet Components
Details
       

 01-10-2009
0.50
Rivet Part 13 Left Inlet Floor Support to Baffles
Details
       

 01-10-2009
0.50
Rivet Left Inlet Components
Details
       

 01-10-2009
0.50
Pre Drill F1A&B to Left Inlet Floor and Bulkhead
Details
       

 01-10-2009
0.50
Pre Drill F11A&B to Right Inlet Floor and Bulkhead
Details
       

 01-10-2009
0.50
Install Right Front Inlet Corner Assembly
Details
       

 01-10-2009
0.50
Install Left Front Inlet Corner Assembly
Details
       

 01-10-2009
0.50
Final Drill Reinf Brackets to Inlet Floors/Bulkhea
Details
       

 01-10-2009
0.50
Debur, Clean, Alodine All Inlet Components
Details
       

 01-10-2009
0.50
Bend Right Inlet Reinforcement Angles - F11A&B
Details
     

 01-09-2009
0.50
Trim Right Front Bulkhead - Lower to Inlet Floor
Details
       

 01-09-2009
0.50
Trim Left Front Bulkhead - Lower to Inlet Floor
Details
       

 01-09-2009
0.00
Initial fitting of Front Bulkheads - Parts 1 & 11
Details
       

 01-09-2009
0.00
Front Bulkheads Lowered to Inlet Floors
Details
       

 01-09-2009
0.50
Fabricate Front Bulkhead Angles - F1A&B, F11A&B
Details
       

 01-08-2009
0.00
Oil Cooler Mounted Too High - Need to Redo
Details
       

 01-08-2009
5.00
5 Iterations of Trimming Top Edges of Baffles
Details
       

 01-07-2009
0.50
Trim Front/Top of Part 9 Side Baffle for Top Cowl
Details
       

 01-07-2009
0.50
Trim Front/Top of Part 3 Side Baffle for Top Cowl
Details
       

 01-07-2009
0.50
Temp Install Right Inlet Baffle and Lower Cowl
Details
       

 01-07-2009
1.00
Rivet Right Inlet Floor - Parts 9, 10, and 10S
Details
       

 01-07-2009
0.50
Install Lower Cowl, Then Upper Cowl; Mark Baffles
Details
       

 01-07-2009
2.00
3 Iterations of Trimming Top Edges of Baffles
Details
       

 01-05-2009
0.50
Temp Install Parts 9&10 - Right Inlet
Details
     

 01-05-2009
2.00
Fabricate Part 10S Reinf Angle; Drill to Right Inl
Details
       

 01-05-2009
0.50
Bend Parts 9&10 - Right Inlet Floor / Baffle
Details
       

 12-20-2008
1.00
Rivet Left Intake Parts 2, 2S, and 3
Details
       

 12-20-2008
0.50
Intall Left Intake Baffles on Engine - Parts 2&3
Details
       

 12-20-2008
1.50
Fabricate Part 2S Angle - Drill to Parts 2 & 3
Details
       

 11-08-2008
1.00
Make Bends in Left Intake Parts 2 & 3
Details
       

 09-27-2008
0.50
Rivet Right Inlet Floor Parts - 10, 10R, 16
Details
       

 09-27-2008
0.50
Install Right Inlet Floor on Engine - Part 10
Details
       

 09-25-2008
0.50
Match Drill Part 10R to Part 10 - Right Inlet Floo
Details
       

 09-25-2008
0.50
Drill Part 2 - Left Inlet Floor to Parts 2R and 14
Details
       

 09-25-2008
0.50
Drill Part 16 Bracket to Right Inlet Floor
Details
       

 09-25-2008
0.50
Debur, Alodine, Rivet Parts 2, 2R, 14 - Left Inlet
Details
       

 09-24-2008
1.00
Fabricate Part 2R Reinf Angle for Left Inlet Floor
Details
       

 09-23-2008
1.00
Rivet R7F Reinf Plate to Part 7 - Right Aft Baffle
Details
       

 09-23-2008
1.00
Install Part 7 on Engine - Right Aft Baffle
Details
       

 09-22-2008
0.50
Trim Part 6 Baffle; Remove Oil Filler Tube
Details
       

 09-22-2008
0.50
Rivet Reinforcement Angle to Part 8
Details
       

 09-22-2008
1.00
Fabricate Diagonal Support Angle for Part 8
Details
     

 09-20-2008
0.50
Install Left Aft Corner Baffles/Oil Cooler on Engi
Details
       

 09-20-2008
0.50
Bolt Oil Cooler to Baffles
Details
       

 09-20-2008
1.00
Acetone, Alodine, Rivet Parts 4&5 - Oil Cooler
Details
       

 09-17-2008
2.00
Final Trim and Debur Oil Cooler Baffle Components
Details
     

 09-16-2008
1.50
Cutout Part 5 for Oil Cooler; Countersink 4&5
Details
     

 09-14-2008
1.50
Fit and Drill Oil Cooler to Baffles
Details
       

 09-14-2008
1.50
Drill / Debur Oil Cooler Baffle Parts (4&5)
Details
       

 07-25-2008
1.00
Fabricate 6 Spacers for Oil Cooler Bolts
Details
       

 03-10-2008
1.00
Part 9: Front Right Side Baffle - Drill & Rivet Re
Details
       

 03-10-2008
1.00
Part 8: Back Right Side Baffle - Drill & Rivet Rei
Details
       

 03-03-2008
1.00
Part 3: Front Left Baffle - Drill and Rivet Reinf
Details
     










Copyright © 2001-2024 Matronics. All Rights Reserved.