Powered By Kitlog Pro v2.0
Dan's Web Site
RV-7A
Panel
Work Logs Found:
39
Category Work Time:
47 Hours
Date
Hours
Work Log Summary
Details
03-30-2007
2.00
Install Parking Brake, Carb Heat, Throttle, Mixtur
Details
03-30-2007
1.00
Install Panel and Vents Permanently
Details
03-30-2007
1.00
Drill and Install Bracket for Engine Control Cable
Details
03-29-2007
1.50
Drill/Dremel Holes in Subpanel for Harnesses/Cable
Details
03-28-2007
1.50
Temporarily Install Panel; Mark Subpanel for Cutou
Details
03-28-2007
3.00
Drill/Dremel Holes in Subpanel for Harnesses/Cable
Details
03-13-2007
0.50
Install Dimmer Switch Knob
Details
02-06-2007
3.00
Wet Sand/Polish Panel, Install Instruments
Details
02-06-2007
3.00
Wet Sand/Polish Panel, Install Instruments
Details
07-31-2006
1.00
Sand/Clean Panel to Prime Again - Gray This Time
Details
07-31-2006
0.50
Prime Panel Using Gray Epoxy Primer
Details
07-24-2006
1.00
Sand/Acetone Panel and Covers for Priming
Details
07-24-2006
1.00
Prime Panel with White Epoxy Primer
Details
07-24-2006
0.50
Inspect Priming
Details
07-22-2006
2.00
Create Anti-Rotation Ring for Ignition Switch
Details
07-15-2006
1.00
Drill Holes for Toggle Switches
Details
07-15-2006
1.00
Debur/Edge Prep Anti-Rotation Strips/Panel for Swi
Details
07-15-2006
1.00
Acetone/Alodine/Rivet Anti-Rotation Strips to Pane
Details
07-07-2006
1.00
Drill Holes for Cabin Heat & Parking Brake Cables
Details
07-07-2006
1.00
Drill Hole for Low Voltage Light; Trim Bracket
Details
07-06-2006
2.00
Cut Holes for Trim Indicators, ELT and Ignition Sw
Details
06-01-2006
2.00
Fabricate/Install SL40 Support Angles in Sub Panel
Details
05-30-2006
0.50
Trim Air Gizmo Tray for Garmin 396 Handheld
Details
05-30-2006
1.00
Fabricate/Install Support Strip for Trays
Details
05-30-2006
1.00
Cut Slot in Sub-Panel for SL40 Comm Tray
Details
05-30-2006
0.50
Acetone/Alodine Rails/Trays; Install Trays
Details
05-28-2006
0.50
Mark Subpanel for SL40 Comm Cutout
Details
05-28-2006
1.50
Drill Air Gizmo Tray to Rails for Garmin 396 GPS
Details
05-27-2006
1.00
Drill SL40 Comm Tray to Rails
Details
05-27-2006
1.00
Drill GTX327 Transponder Tray to Rails
Details
05-27-2006
1.00
Drill GMA340 Audio Tray to Rails
Details
05-26-2006
1.00
Rivet Support Angles for Radio Stack to Panel
Details
05-26-2006
1.00
Fabricate / Drill Support Angles for Radio Stack
Details
05-14-2006
2.00
Cut Panel for Radios and GPS
Details
05-12-2006
0.50
Temporarily Install Dynon's, Panel; Sit Back and E
Details
05-12-2006
0.50
Drill Remaining Instrument Attach Holes
Details
05-11-2006
0.50
Use Jig to Drill Instrument Attach Holes
Details
05-11-2006
0.50
Temporarily Install Dynon EMS in Panel
Details
05-11-2006
1.50
Mark / Punch Eight 3-1/8" Instrument Panel Holes
Details
SITE NAVIGATION
Contact Builder
RV-7A Home
Category
# Logs
# Hours
All
1974
2363
Ailerons
35
56
Assembly
5
6
Avionics
4
4
Baffles
134
110
Big Dig
8
Brakes
23
26
Canopy
64
83
Canopy Frame
144
152
Cowl
68
74
Electrial
120
96
Electrical
120
96
Elevator
58
90
Empennage
30
48
Engine
64
42
Filtered Air Box
26
22
Finish Kit
4
4
Firewall Forward
27
24
Flaps
50
64
Forward Fuselage
44
53
Fuel System
28
36
Fuselage
294
460
Gear
32
38
Hangar
2
Hardware
5
4
Horizontal Stabilizer
42
60
Left Aileron
4
6
Left Flap
3
2
Left Fuel Tank
38
68
Left Wing
90
117
Paint
1
0
Panel
39
47
Photo Shoot
25
2
Prop
4
4
Right Aileron
2
2
Right Flap
3
2
Right Fuel Tank
43
60
Right Wing
84
102
Rudder
16
30
Rudder II
31
54
Seats
9
21
Service Bulletin: No
7
6
Spinner
17
15
Systems
1
0
Training
3
Vertical Stabilizer
23
31
Wings
100
146
Copyright © 2001-2024 Matronics. All Rights Reserved.
