KitLog pro

Powered By Kitlog Pro v2.0

MICHAEL'S WEB SITE
Work Logs Found: 53
Category Work Time: 283 Hours
 Date
Hours
Work Log Summary

Details

 11-10-2007
3.00
Glued Leading Edge of Canard Into Jig

 11-09-2007
3.00
Set Up Jig and Fit Canard in Place

 11-05-2007
2.00
Drilled Holes for Lift Tabs

 11-04-2007
6.00
Layed Up "U" section of canard

 11-03-2007
6.00
Alagined and Jigged Canard Foam

 10-16-2007
4.00
Working On Lift Tab Installation and Foam Jig

 10-11-2007
8.00
Install Antennae in Winglets

 09-23-2007
8.00
Rudder Layup

 09-20-2007
1.00
Sand Bottom Spar Cap

 09-18-2007
1.00
Sand Bottom Wing Spar

 09-17-2007
1.00
Bottom Wing Spar Cap Sanding

 09-14-2007
4.00
Prepping Wing For Bottom Layup
Details

 09-13-2007
4.00
Installed COM In Wing
Details

 09-08-2007
10.00
Left Wing Bottom Spar Cap Layup
Details

 03-10-2007
10.00
Installed Top Wing Layup
Details

 03-03-2007
8.00
Installed Top Spar Cap
Details

 02-24-2007
8.00
Glassed Bottom of the wing

 02-16-2007
2.50
Bottom of Wing Prep for Glassing
Details

 12-30-2006
8.00
Installed Antenna inside foam
       

 12-23-2006
8.00
Installed Bottom Spar Cap
     

 12-04-2006
2.00
Bond leading edge of wing to shear web
Details
       

 12-03-2006
8.00
Wing Cap
Details
     

 12-02-2006
5.00
Wing Attach Points
Details
       

 11-11-2006
8.00
Started Jigging and Glueing Wing Cores
Details
       

 11-05-2006
4.00
Wing Jigs Laid out Wings
Details
       

 10-16-2006
8.00
Main Wing Jigs
Details
       

 10-08-2006
3.00
Cut Out Temp. Firewall
Details
     

 10-03-2006
3.00
Fire Wall Cutout
Details

 09-17-2006
10.00
Installed Top of Spar Box
Details
     

 09-16-2006
12.00
Worked on Wing Spar, Completed First Layup
Details
       

 09-01-2006
6.00
Spar
Details

 08-26-2006
5.00
Building Jig for Spar
Details
     

 07-30-2006
10.00
Hot Wired Canard
Details

 04-16-2006
4.00
Prepare Foam For Layup
Details
     

 04-15-2006
4.00
Dished Out Control Stick and Fuel Sight Areas
Details
       

 04-06-2006
2.00
Cut Pieces for Inside Shaping of Fuselage
Details

 04-03-2006
3.00
Scrapped Bad Longeriron Parts, Cleaned Epoxy Pump
Details

 04-02-2006
12.00
Set Up Longerirons
Details

 04-01-2006
6.00
Fuselage Sides, Build Frames and Extended Table
Details

 03-26-2006
8.00
Trimmed Instrument Panel and Started on Forms for
Details

 03-19-2006
4.00
Continued Work on Instrument Panel and Aft Landing
Details

 02-28-2006
3.00
Instrument pnl front and remaining hard points
Details

 02-26-2006
6.00
Front Side of Instrument PNL, and Landing Gear Bul
Details
       

 02-23-2006
3.00
Traced Then Layed Out Rear Landing Gear Bulkhead
Details
     

 02-21-2006
2.00
Same as 2/20/06 mirror image layup
Details

 02-20-2006
2.00
layed up 22 BID for "hard point" on Landing Gear B
Details

 02-18-2006
5.00
Cut Out Instrument Panel and 1st Layup
Details
     

 02-16-2006
3.00
Bulkhead F22 and F28 Trimmed Glass
Details
       

 02-13-2006
5.50
Bulkheads F22 and F28 Last Layup
Details

 02-12-2006
5.00
Bulkhead F22 and F28
Details

 02-10-2006
4.00
Front Seat Last Layup
Details
       

 02-09-2006
8.00
Front Seat repair
Details
       

 02-08-2006
4.00
Front Seat first layup
Details










Copyright © 2001-2020 Matronics. All Rights Reserved.