KitLog pro

Powered By Kitlog Pro v2.0

Bill's RV-10 Builder Page
Work Logs Found: 62
Category Work Time: 154 Hours
 Date
Hours
Work Log Summary

Details

 03-31-2007
10.00
Empennage Attach
Details
     

 03-07-2007
2.50

Details

 03-06-2007
3.00
Attached elevators and started pushrod assembly
Details
       

 02-21-2007
2.50
Resolved issue with stab horn drilling
Details
     

 02-18-2007
5.30
RH elevator attach and control horn drill
Details

 02-18-2007
2.50
Attach Stab to Tailcone
       

 02-17-2007
1.50
RH Elevator attach
Details

 02-15-2007
2.70
LH Elevator attach
Details
       

 02-13-2007
1.50
Began elevator to stab attach
Details

 01-31-2007
3.20
Completed elevators and trim tabs
Details
     

 01-30-2007
3.50
Riveting elevator & trim tab hinge - 1 complete
Details

 01-27-2007
2.00
Proseal and rivet elevators
Details

 01-14-2007
1.50
Riveting trim tab

 01-13-2007
4.00
Finishing elevator riveting

 01-10-2007
1.00
Prosealed elevator trailing edges

 01-06-2007
8.00
Riveting elevator

 01-05-2007
5.50
Riveting Elevator skins, spars, tip
Details

 01-03-2007
1.00
Rivet elevator skins
Details

 12-27-2006
3.00
Elevator riveting and assembly

 12-25-2006
1.70
Rivet RH elevator rear spar
Details

 12-23-2006
1.50
Replace RH rear elevator spar and half rib
Details

 12-16-2006
2.00
Riveted spars to ribs and skins
Details

 12-14-2006
1.50
Elevator riveting - skins to ribs
Details

 12-13-2006
3.00
Elevator riveting

 12-12-2006
1.00
Riveted Elevator Horns
Details

 12-12-2006
3.75
Rivet Tip ribs, spar plates and root ribs

 12-12-2006
1.00
Primed Elevator and trim tab skins
Details

 12-11-2006
2.00
Rivet tip ribs

 12-11-2006
4.50
Prep and Prime elevator and trim tab

 12-10-2006
0.30
slight bend in trailing edge of elevator skins
Details

 12-10-2006
0.50
Match drilled WD-415 replacement part from Rivethe
Details
     

 12-10-2006
2.00
Cleaned Elevator & Trim tab parts for priming
Details

 12-10-2006
0.75
Adjusted angle on elevator flanges with hand seame
Details

 11-15-2006
1.00
Deburr and dimple elevator trim plates

 11-11-2006
3.00
Trim Tab
Details
       

 11-10-2006
2.00
dimpled remaining elevator parts - tough ones

 11-10-2006
1.00
Cut clamping blocks for trim tab

 11-08-2006
0.50
Foam rib cutting and sanding

 11-08-2006
0.50
foam rib cutout & sanding

 11-08-2006
1.00
Cutting out 6 trim tab jigs
Details

 11-06-2006
4.00
elevator - misc dimple and CS
Details

 11-05-2006
2.50
Elevator spars - CS and dimple

 10-31-2006
1.50
Disassemble LH elevator, deburr, dimple

 10-31-2006
1.50
dimpled RH elevator skins

 10-30-2006
2.00
Elevator disassembly, deburring, dimple

 10-23-2006
1.50
Riveted HS attach brackets - out of sequence
Details
     

 10-22-2006
1.50
Completed skin riveting
Details

 10-09-2006
1.00
Final drilling Elevator

 10-07-2006
1.50
Initial assembly of elevators - clecoing cont

 10-06-2006
2.00
Riveting HS - cont

 10-06-2006
1.00
Initial Assembly of Elevators - cont
       

 10-05-2006
3.00
Riveting skins on HS - continued

 10-03-2006
4.00
Riveting HS skins

 10-02-2006
5.00
Riveting HS skins

 10-01-2006
4.50
HS riveting & Elevator assembly
Details

 09-30-2006
1.00
Riveting front spar of HS (cont)

 09-30-2006
2.50
Cleco'd Elevator
Details

 09-28-2006
2.50
Riveted HS Spar - Cleco'd elevator

 09-26-2006
1.00
Cleco Elevator ribs and spars

 09-24-2006
6.00
Riveted HS nose ribs and LH Bottom spar to skin
Details

 09-23-2006
3.50
Assembled and matchdrilled elevator tip ribs
Details
       

 09-13-2006
2.00
cleco'd stab skins & Cut 3 wing cradles
Details
     










Copyright © 2001-2024 Matronics. All Rights Reserved.