KitLog pro

Powered By Kitlog Pro v2.0

JOHN'S WEB SITE
Work Logs Found: 55
Category Work Time: 134 Hours
 Date
Hours
Work Log Summary

Details

 03-07-2020
1.00
FINISHED MAIN SPAR!!
Details
       

 03-05-2020
2.25
Lay up 4 layers of UNI on top of main spar
     

 03-02-2020
1.75
Sand spar #2 in main spar to final dimension
Details
     

 02-29-2020
9.00
Layup spar #2 in main spar and peel ply
Details
     

 02-24-2020
2.00
Sand spar #1 in main spar to final dimension
Details
       

 02-21-2020
11.00
Lay up Spar 1 in main spar and Peel Ply - LONG day
Details
       

 01-25-2020
1.25
Finalize shaping of foam and wood inserts in main
Details
     

 01-20-2020
2.50
Shape top foam piece of main spar
Details
       

 01-04-2020
1.00
Inspect hard point adhesion and cut foam insert te
Details
       

 01-04-2020
1.25
Epoxy all main spar foam inserts into place
Details
       

 01-02-2020
1.25
Epoxy hard point laminates into spar
Details
       

 01-01-2020
1.50
Trim out first spar layup
Details
       

 12-23-2019
6.25
Redo 6-layer base fiberglass layup
Details
       

 11-10-2019
0.75
Epoxy hardpoints into main spar DWA's
Details
     

 11-09-2019
4.25
Layup 6-layer fiberglass base layup
Details
       

 11-08-2019
0.75
Trim out hard point inserts for main spar
Details
     

 11-08-2019
0.50
Line main spar jig with contact release paper
Details
     

 11-08-2019
1.25
Cut fiberglass for main spar lauyups
Details
       

 11-05-2019
3.25
Lay up 1/4" thick fiberglass plate for hard points
Details
     

 11-03-2019
1.75
Route out for hardpoint inserts in DWA-4 and DWA-8
Details
       

 10-27-2019
1.75
Cut and laminate two DWA-5's
Details
       

 10-25-2019
2.25
Trim to final size DWA-4 and DWA-8
Details
     

 09-25-2019
0.25
Final laminate for DWA-4 and DWA-8. Looking good!
Details
       

 09-23-2019
2.50
Layup DWA-8 Laminate
Details
       

 09-21-2019
2.25
Layup DWA-4 Laminate
Details
       

 09-20-2019
8.00
Construct solid block form for DWA-4 and DWA-8
Details
       

 09-11-2019
1.00
Determined that spar was unacceptable and destroy.
Details
       

 07-04-2019
9.00
Lay up second spar in centersection spar.
Details
       

 06-23-2019
11.00
Lay up first spar in centersection spar.
Details
       

 06-14-2019
0.75
Repair edges of center foam section for main spar
Details
       

 06-02-2019
0.10
Inspecting underside of centersection spar. I wil
Details
       

 06-01-2019
0.50
Sand down high point edges of curved wooden sectio
Details
       

 05-30-2019
2.50
Finish sanding middle foam section of centersectio
Details
       

 05-27-2019
2.00
Began to sand additional high density foam piece i
Details
     

 05-26-2019
1.75
Unmold spar from jig and trim fiberglass edges.
Details
       

 05-25-2019
0.75
Epoxy second piece of foam to forward face of main
Details
       

 05-24-2019
3.50
Lay in 6 layers of UNI into main spar jig.
Details
       

 05-24-2019
3.00
Install foam and laminated wood pieces into main s
Details
       

 05-21-2019
1.50
Finish cutting last piece of foam and finished tri
Details
       

 05-20-2019
1.50
Final trimming and fitting of foam inserts for ma
Details
       

 05-19-2019
2.00
Rough cut foam inserts for main spar and start to
Details
       

 05-18-2019
2.50
Make final alignment for main spar wood inserts an
Details
       

 04-21-2019
0.75
Begin final alignment markup on centersection spar
Details
     

 04-19-2019
1.00
Use Flox to Epoxy all 4 Fiberglass Hardpoints into
Details
     

 04-18-2019
1.20
Rout Out Area for Fiberglass Hardpoints in DWA-4 a
Details
       

 04-07-2019
1.25
Cut Out Hard Points for Main Spar Inserts
Details
     

 03-28-2019
2.00
Layup 21 plies for 1/4" Hardpoints for Main Spar
Details
       

 03-21-2019
3.00
Cut fiberglass for first main spar layup, lower wi
Details
       

 02-28-2019
2.50
Trim out DWA-8 and DWA-4 to final shape.
Details
       

 02-25-2019
1.50
Layup 8-ply plywood laminate for DWA-4
Details
       

 02-25-2019
0.30
Add final end pieces to DWA-5's
Details
       

 02-18-2019
1.50
Laminate 8 plys for DWA-8
Details
       

 02-14-2019
1.00
Cut new wooden parts to test new method to make DW
Details

 02-09-2019
2.50
Define ends of main spar on jig
Details
       

 02-07-2019
0.50
Laminate base 3-layers of plywood for DWA-5's
Details
     










Copyright © 2001-2024 Matronics. All Rights Reserved.