KitLog pro

Powered By Kitlog Pro v2.0

RV-6A - GBC
Work Logs Found: 126
Category Work Time: 392 Hours
 Date
Hours
Work Log Summary

Details

 05-25-2017
3.00
Adjustments - inlets
Details
       

 05-10-2017
1.00
Cowl - exh heat on fiberglass
Details
       

 05-09-2017
7.00
Baffles & induction
Details
       

 04-13-2017
2.00
Re-install Mags - repaired
Details
       

 04-06-2017
3.00
Mags - Pulled & shipped
Details
       

 04-05-2017
4.00
Mags/Plugs - plugs & cleaned
Details

 03-08-2017
4.50
Engine baffle adjustments
Details
       

 03-07-2017
2.00
Baffles and 'cylinder' wraps
Details

 02-15-2017
6.00
Baffles - Flexible edges
Details
       

 02-08-2017
6.00
Cowl - BAF flexible edge
Details
       

 01-20-2017
2.00
Tune-up - New Plugs
Details
       

 01-14-2017
6.00
Tune-up
Details
     

 01-13-2017
5.00
Tune-up - Diagnostics & Plug gaps
Details
     

 01-07-2017
4.50
Compression Test -
Details

 08-26-2016
4.00
Brake bleed & engine start
Details
     

 08-24-2016
2.50
First Engine Start - Test
Details
       

 08-24-2016
3.50
EFIS - Engine run follow-up
Details
     

 08-16-2016
4.00
Sensor and EFIS setup - adjustments
Details
       

 08-15-2016
4.00
Fuel & Oil sensor - troubleshooting
Details
       

 08-12-2016
4.00
Wires, fuel lines etc
Details

 08-10-2016
6.00
FWF - secure wire
Details
       

 08-08-2016
5.00
Startting circuits - troubleshoot
Details

 07-27-2016
1.50
Check the timing
Details
       

 07-26-2016
2.50
Starting Vibrator - & Ignition Switch wiring
Details
       

 07-25-2016
4.00
Starting Vibrator - Mount (& P-Lead)
Details
       

 07-22-2016
2.50
Starting Vibrator - fabricate doubler
Details
     

 07-20-2016
3.00
Magnetos - Mag to Eng timing
Details

 07-19-2016
2.50
Starting Vibrator - wire harness
Details
     

 07-18-2016
2.00
Mag - P-Leads & Components
Details
       

 07-16-2016
4.00
Magneto - evaluation
Details
       

 05-26-2016
7.00
Engine baffle - oil cooler duct
Details
       

 05-25-2016
5.50
Baffle - SCAT duct to oil cooler
Details
       

 05-17-2016
5.00
Clamps, washers and misc
Details
       

 05-14-2016
7.00
New Alternator, Sump & other bolts
Details
       

 05-10-2016
5.00
Engine - more hoses, fasteners, etc
Details
     

 05-09-2016
6.00
Engine - hoses & throttle
Details
       

 04-26-2016
0.50
Order hoses - TS FlightLines
Details
     

 04-22-2016
5.50
Cowl - more riveting hinges
Details
       

 04-20-2016
7.00
Cowl, (Hinges), FAB alt air, engine
Details
       

 04-18-2016
7.00
Vetterman Exh & cowl fit
Details
       

 04-15-2016
5.00
Misc -
Details
       

 04-08-2016
9.00
FWF - Hoses, and more
Details
       

 04-07-2016
5.00
Throttle cable - replace & configure
Details

 04-06-2016
6.00
Hoses, baffles, & wires
Details
       

 04-05-2016
2.50
Engine - FI & cables
Details
       

 04-04-2016
5.50
FI - Cables & distribution
Details
       

 04-02-2016
9.00
FW prep & hang the engine
Details
       

 03-26-2016
4.50
FWF - Sensors
Details
       

 03-09-2016
2.00
Torqued & Secured
Details
       

 03-07-2016
2.00
EMS - Sensors (CHT & EGT)
Details
       

 12-26-2015
5.00
FWF - Oil Cooler & mount
Details
       

 04-02-2015
2.00
Some engine, and fuselage stuff
Details
       

 03-25-2015
1.50
Parts prep
Details

 03-11-2015
2.00
Ignition Wiring
Details
       

 03-06-2015
2.00
Fuel Pump Gear -
Details
     

 03-05-2015
1.20
Assembly prep
Details

 03-04-2015
3.00
Accessory Cover & Fuel Pump
Details
       

 02-28-2015
1.00
Review - Check & preparations for assembly
Details
     

 02-22-2015
2.00
Engine - moved to hangar
Details
       

 11-29-2014
3.00
AFP - Fuel Divider
Details
       

 10-27-2013
4.00
Engine Baffles - 11th step? (& Cowl)
Details
       

 10-19-2013
2.00
Cowl - more fitting
Details
     

 10-18-2013
2.00
Engine Baffles - 10th step
Details
       

 10-17-2013
1.50
Engine Baffles - 10th step
Details

 10-14-2013
8.00
Engine Baffles - 9th step
Details
       

 10-13-2013
3.50
Engine Baffles - 9th step
Details
       

 10-12-2013
6.00
Engine Baffles - 8th step
Details
       

 10-11-2013
2.00
Engine Baffles - 7th step (again)
Details
       

 10-09-2013
1.00
Engine Baffles - OOPS
Details
       

 10-07-2013
1.50
Engine Baffles - 7th step
Details
       

 10-06-2013
3.00
Engine Baffles - 6th step
Details
       

 10-05-2013
3.50
Engine Baffles - 6th step
Details
       

 10-04-2013
4.00
Engine Baffles - 5th step
Details
       

 10-04-2013
6.00
Engine Baffles - 5th step
Details
       

 10-03-2013
2.50
Engine Baffles - 4th step
Details
       

 10-02-2013
3.00
Engine Baffles - 3rd step
Details
       

 10-02-2013
1.00
Engine Baffle - 3rd step
Details
       

 10-01-2013
3.00
Engine Baffles - 2nd step
Details
       

 09-30-2013
2.50
Engine Baffles - 1st step
Details
       

 09-28-2013
2.00
FW - sensors/fittings
Details
       

 09-27-2013
2.00
FW - EMS wiring
Details
       

 09-26-2013
1.00
FW - clamp
Details
       

 09-24-2013
1.00
FWF - Order parts
Details

 09-22-2013
3.00
Engine - strip down
Details
       

 09-21-2013
0.60
FW - Oil Cooler mount
Details
     

 09-21-2013
1.50
FW - Oil cooler mount
Details
       

 09-20-2013
4.00
FW - Oil Cooler remote mount
Details
       

 09-19-2013
1.00
Dynon - Sensors & clamp
Details
       

 09-18-2013
2.50
FW - penetration & clamps
Details
       

 09-15-2013
1.50
FWF - fuel lines
Details
       

 09-02-2013
6.00
FWF - various
Details
       

 08-31-2013
2.00
FWF - misc tasks
Details
       

 05-03-2013
2.00
Exhaust hangers & cowl support
Details
       

 04-21-2013
2.00
Cowl hinges
Details
       

 04-07-2013
2.50
Mount - remove washers
Details

 10-28-2012
1.00
Gear Ring Assembly
Details
     

 10-26-2012
2.00
Gear Ring Assembly
Details
     

 12-03-2011
0.50
Inventory Vans order
Details
       

 10-28-2011
0.30
Prop spinner arrived
Details
       

 10-25-2011
1.00
Prop arrived - inspect
Details
       

 09-30-2011
4.00
Crankshaft lug replacements 1/2"
Details
       

 06-10-2011
4.00
F/W position - various
Details
       

 06-08-2011
0.70
Oil Cooler Mounting - more fab
Details
     

 06-07-2011
1.00
Oil Cooler Mounting - more fab
Details
     

 06-06-2011
3.00
Oil Cooler Mounting - fabricate
Details
       

 05-10-2011
0.70
Hang the conical mount - termporary
Details
       

 03-25-2011
2.50
Sump swap
Details
       

 03-17-2011
2.50
Parted out 1st O-360
Details
     

 03-02-2011
3.00
Engine prep issues
Details
       

 02-22-2011
4.00
Research Conical Eng Mount
Details
       

 02-21-2011
4.00
See the engine and decide
Details
       

 02-18-2011
4.00
First look at low-time engine
Details
       

 10-17-2010
1.00
More cleaning
Details
     

 10-16-2010
1.00
Lycoming Models - research
Details
       

 10-15-2010
1.00
Parts cleaning
Details
       

 10-14-2010
1.00
Cleaning more parts
Details
       

 10-13-2010
1.00
Cleaning parts
Details
     

 10-04-2009
4.00
Engine tear-down
Details
       

 10-03-2009
2.50
Engine tear-down
Details
       

 07-20-2009
1.50
Engine Stand - mount
Details
     

 06-29-2009
2.50
Preliminary engine evaluation
Details
       

 06-27-2009
1.00
Engine inspection
Details
       

 06-25-2009
3.00
Engine condition review
Details
       

 06-23-2009
0.00
Engine selection
Details
       

 06-21-2009
0.00
Research engine choices and options
Details

 06-19-2009
0.00
Engine Research
Details










Copyright © 2001-2024 Matronics. All Rights Reserved.