KitLog pro

Powered By Kitlog Pro v2.0

Swami's Web Site
Work Logs Found: 65
Category Work Time: 140 Hours
 Date
Hours
Work Log Summary

Details

 11-10-2019
2.50
install left wing pitot+set-up for riveting skin
Details

 11-10-2019
2.00
finish riveting right wing bottom skin
Details

 11-09-2019
3.50
start rivetig right wing bottom skin
Details

 10-13-2019
1.00
install safety wire on AP roll-servo 9 pin
Details

 04-21-2017
2.50
finish installing wing root plate nuts

 04-20-2017
2.50
continue install of wing root plate nuts

 04-18-2017
1.00
start install of wing root plate nuts

 04-09-2017
2.00
remove left wing, rivet right wing aileron brace s
Details

 04-02-2017
0.25
remove right wing

 04-01-2017
1.00
rig right aileron to stick

 04-01-2017
1.00
rig left aileron to stick

 03-19-2017
1.25
install left flap. adjusted range of motion

 03-18-2017
1.50
install right flap and adjust range of motion

 03-18-2017
6.00
complete install of wing root fairings
Details

 03-17-2017
1.00
install right fuel tank attach bracket

 03-17-2017
2.00
begin install right wing root fairing

 03-15-2017
2.50
install left fuel tank attach bracket

 03-15-2017
1.00
drill fuse center/wing skin screw holes

 03-13-2017
1.00
recheck fwd sweep
Details

 03-13-2017
1.00
drill rear spar holes to final size

 03-13-2017
2.00
chack flaps (OK), recheck incidence.pilot hole in
Details

 03-12-2017
1.25
square wings to fuselage
Details

 03-12-2017
0.75
install right Wing! level fuselage

 03-11-2017
2.00
twist left, right wing red/blk wingtip light wires

 03-11-2017
3.00
Install left wing!

 02-11-2017
2.50
run heated pitot wiring in left wing
Details

 02-06-2017
1.50
run left wingtip wires, stall and fuel sender wire
Details

 02-05-2017
3.00
prep,prime,install left flap hinge/pin
Details

 02-04-2017
1.50
set neutral position of left aileron
Details

 02-04-2017
3.00
install left fuel tank on wing
Details

 01-29-2017
1.50
shrink wrap stall warning wires
Details

 01-28-2017
3.00
trim right and left wing aft spar attach
Details

 01-21-2017
3.00
test right fuel tank. begin fwd fuse ctr section

 01-16-2017
2.00
Install right Flap. bend and drill hinge pin

 01-16-2017
1.00
Finish drilling right Flap hinge + Prime

 01-16-2017
1.00
drill wiring holes in wing and run wire
Details

 01-15-2017
2.00
begin install of right Flap

 01-14-2017
2.50
seal fuel tanks

 01-07-2017
2.00
install roll AP servo in Right wing

 01-05-2017
2.00
reroute static line

 12-10-2016
5.00
Prep tank for sealing. Install ailerons
Details

 12-05-2016
3.00
Install aileron brackets to ailerons
Details

 12-04-2016
2.50
Fab and install L+R skin access panels
Details

 12-03-2016
2.50
re-fab antihangup strap. build R fuel sender
Details

 10-28-2016
4.00
Complete L wing skin. Drill L tank sender hole
Details

 10-16-2016
2.00
install trap door and anti-hangup in L fuel tank
Details

 10-13-2016
1.00
Fab trap door for inverted fuel tank mod
Details

 10-12-2016
7.00
Aileron bracket and fairing, Pitot mast, Complete
Details

 10-11-2016
1.00
Remove fuel tank
Details

 10-08-2016
3.50
Pitot bracket install
Details

 09-29-2016
1.00
match drill L flap brace, C/S rear spar
Details

 09-28-2016
1.00
Fab stall warning access panel
Details

 09-25-2016
2.75
begin work on left wing
Details

 09-24-2016
3.00
finish work on right wing skin
Details

 09-23-2016
1.00
debur spar and ribs under skin
Details

 09-22-2016
2.00
Prime aileron brace, match drill skin
Details

 09-21-2016
1.00
more work on flap bracket and aileron brace
Details

 09-14-2016
2.00
Prep work on Right wing Flap brace
Details

 09-12-2016
2.50
Rivet aileron brackets to Right wing
Details

 09-11-2016
2.00
Finish aileron bracket build-up
Details

 09-05-2016
3.00
Install R bellcrank, prep aileron attach brackets
Details

 09-04-2016
6.00
Complete pushrod Fab (7)
Details

 09-03-2016
4.50
Begin work on wings. aileron bellcrank
Details

 07-07-2016
0.00
Inventory QB Wing crates

 07-06-2016
0.00
Recieved QB wing crates










Copyright © 2001-2020 Matronics. All Rights Reserved.