Date
|
Hours
|
Work Log Summary
|
Details
|
12-07-2014
|
1.00
|
Seat Back assembly
|
Details
|
|
|
|
12-07-2014
|
9.00
|
Rudder Pedals
|
Details
|
|
|
10-19-2014
|
9.50
|
Completion of Right Wing tank
|
Details
|
|
|
10-13-2014
|
4.00
|
Installation of Auto pilot servo
|
Details
|
|
|
10-12-2014
|
3.00
|
Completion of Aeirlon and installation on wing
|
Details
|
|
|
09-28-2014
|
4.00
|
Dimpling outet Right hand wing skins
|
Details
|
|
|
09-20-2014
|
7.00
|
Dimpling wing skins
|
Details
|
|
|
|
09-07-2014
|
7.50
|
Match drilling, dimpling, inspection platenuts etc
|
Details
|
|
|
08-10-2014
|
6.50
|
Completing Wing Tank left side
|
Details
|
|
|
|
07-01-2014
|
3.00
|
Left Elevator
|
Details
|
|
|
03-23-2014
|
2.00
|
Attaching the Aierlon Gap seal
|
Details
|
|
|
|
03-22-2014
|
5.00
|
Completioin of Aierlon - Left Side
|
Details
|
|
|
|
03-09-2014
|
4.00
|
Completion of Aierlon
|
Details
|
|
|
03-02-2014
|
1.00
|
Completing the right flap
|
Details
|
|
|
|
02-23-2014
|
4.00
|
Completing the rudder
|
Details
|
|
|
02-22-2014
|
3.50
|
Pre Cover Inspection
|
Details
|
|
|
|
02-10-2014
|
4.00
|
Aierlon Hinge and Brackets and pushtubes
|
Details
|
|
|
01-26-2014
|
1.00
|
Aierlon Bracket and Bellcrank
|
Details
|
|
|
|
01-25-2014
|
1.50
|
Aierlon Brackets and bellcrank
|
Details
|
|
|
|
01-01-2014
|
5.00
|
Reviewing aft work on left wing
|
Details
|
|
|
|
12-26-2013
|
2.00
|
Aierlon skin riveting
|
Details
|
|
|
10-14-2013
|
1.00
|
Aierlons and review after move
|
Details
|
|
|
|
05-25-2013
|
6.00
|
Left Flap
|
Details
|
|
|
05-08-2013
|
2.00
|
Took down uprights and moving on to Flaps
|
Details
|
|
|
05-05-2013
|
5.00
|
placed right wing skin on the ribs and riveted all
|
|
|
|
05-04-2013
|
7.00
|
Preparing the trim and flap, aierlon bits for prim
|
Details
|
|
|
04-13-2013
|
2.00
|
Deburring right wing inboard panel
|
Details
|
|
|
|
02-24-2013
|
6.00
|
Right tank assembly and Pro SEAL 5 of 7 ribs
|
Details
|
|
|
02-16-2013
|
6.00
|
Wings and skins
|
Details
|
|
|
02-13-2013
|
3.00
|
Assembly of leading edge right wing
|
Details
|
|
|
|
02-11-2013
|
1.00
|
Finished the rear lower rivets in wing
|
Details
|
|
|
|
02-05-2013
|
1.00
|
prepared the leading edge and riveted to Spar
|
Details
|
|
|
|
02-03-2013
|
8.00
|
Riveting the wing skins to the skeleton
|
|
|
|
|
02-02-2013
|
3.00
|
Placing the skins onto the wing skeleton
|
|
|
|
|
01-22-2013
|
2.00
|
finished the leading edge riveting
|
Details
|
|
|
|
01-21-2013
|
1.50
|
Assembled leading edge section and W 423
|
Details
|
|
|
|
01-20-2013
|
5.00
|
Removed Leading edge and dimpled ribs and skins
|
Details
|
|
|
|
01-19-2013
|
3.00
|
Dimmpling of wings skins
|
Details
|
|
|
01-01-2013
|
4.50
|
Installation of tank Stiffeners, drain and filler
|
Details
|
|
|
12-30-2012
|
5.00
|
Fuel Tanks
|
Details
|
|
|
|
12-26-2012
|
5.00
|
Capacitative fuel quantity sender Left tank
|
Details
|
|
|
12-22-2012
|
3.00
|
Vent tube holders and dimpling tanks ribs
|
Details
|
|
|
|
12-02-2012
|
4.00
|
Fit the drain and fill flanges and dimple T skin
|
Details
|
|
|
|
11-30-2012
|
1.00
|
Coountersink the T 701 to the Tank Baffle holes
|
Details
|
|
|
|
11-04-2012
|
5.00
|
Wing tank work
|
Details
|
|
|
11-03-2012
|
3.00
|
Fabrication of T 403 angle and install T 410
|
Details
|
|
|
10-27-2012
|
0.50
|
forming T 405 Tank attach angle
|
Details
|
|
|
|
10-17-2012
|
4.00
|
Intsallation of tank 708 Access Plates Right and
|
Details
|
|
|
09-30-2012
|
2.00
|
Installing fuel drain valves and fuel tank non ven
|
Details
|
|
|
09-23-2012
|
2.50
|
installing the Capacitative fuel quantity sender
|
Details
|
|
|
|
09-05-2012
|
3.50
|
Dimpling the tank skins
|
Details
|
|
|
|
08-21-2012
|
5.00
|
Right wing tank preparation and assembly
|
Details
|
|
|
06-05-2012
|
2.00
|
Continuing the install to left wing of the Z angle
|
Details
|
|
|
|
06-04-2012
|
2.00
|
Fixing nutplates to Z angle and bolting to spar
|
Details
|
|
|
|
05-26-2012
|
1.00
|
|
Details
|
|
|
|
05-24-2012
|
3.00
|
Leading edge assembly
|
Details
|
|
|
|
05-06-2012
|
5.90
|
Affixing the skins and match drilling to Spar and
|
Details
|
|
|
05-05-2012
|
3.00
|
Affix clecoes to wing skins and to Spar
|
Details
|
|
|
|
04-09-2012
|
0.50
|
Drilled doubler to the wings skin
|
Details
|
|
|
|
04-08-2012
|
4.00
|
prime wing skins
|
Details
|
|
|
|
04-02-2012
|
1.00
|
making wing walk doubler
|
Details
|
|
|
|
04-01-2012
|
9.00
|
Preparation of wing skins and jigs
|
Details
|
|
|
|
03-12-2012
|
1.00
|
Installation of grommets in wing
|
Details
|
|
|
|
03-09-2012
|
1.50
|
Orgnizing the wing skin parts
|
Details
|
|
|
|
03-04-2012
|
4.00
|
Reinstalled wing to upright holders and took out r
|
Details
|
|
|
|
03-03-2012
|
6.00
|
erection of wing jig
|
Details
|
|
|
|
02-28-2012
|
1.00
|
Rib Straightening
|
Details
|
|
|
02-25-2012
|
5.00
|
Completing the rear right spar
|
Details
|
|
|
02-20-2012
|
2.00
|
Preparation of the rear spar, doubler installation
|
Details
|
|
|
|
02-19-2012
|
8.00
|
Painting, priming, painting some more........
|
Details
|
|
|
02-18-2012
|
8.00
|
Preparing the Wing components for assembly
|
Details
|
|
|
02-11-2012
|
4.00
|
Rear Spar
|
Details
|
|
|
|
02-08-2012
|
3.00
|
Preparation of rear wing spar
|
Details
|
|
|
|
02-06-2012
|
1.00
|
Aierlon hinges
|
Details
|
|
|
|
02-05-2012
|
6.00
|
Installing the aierlons bellcrank
|
Details
|
|
|
02-04-2012
|
3.00
|
Wing Tie Downs
|
Details
|
|
|
02-01-2012
|
2.00
|
Install platenuts for access panels on wing spars
|
Details
|
|
|
|
01-30-2012
|
2.50
|
Continuing the installation of platenuts on right
|
Details
|
|
|
01-26-2012
|
3.00
|
Preparing the Spar for the wing tanks
|
Details
|
|
|
01-22-2012
|
1.00
|
Reading the Wings section over
|
Details
|
|
|
|
01-22-2012
|
2.00
|
|
Details
|
|
|
|
01-21-2012
|
3.00
|
Control horn installation
|
Details
|
|
|
|
01-20-2012
|
2.00
|
Trim tab Construction
|
Details
|
|
|
01-07-2012
|
2.00
|
Electric Trim Servo Install
|
Details
|
|
|
01-05-2012
|
2.00
|
Dimpling and installation of trim backing plate
|
Details
|
|
|
|
01-03-2012
|
2.00
|
Trim motor and package
|
Details
|
|
|
|
12-06-2011
|
1.50
|
Dimpling ribs and counterweight skin
|
Details
|
|
|
|
12-01-2011
|
3.00
|
fabricating elevator counterweight
|
Details
|
|
|
|
11-01-2011
|
2.00
|
right elevator kin to skeleton
|
Details
|
|
|
|
10-23-2011
|
2.50
|
703 to 704 and rivet to 702 spar
|
Details
|
|
|
|
10-10-2011
|
2.00
|
dimpling, shaping of elevator weights
|
Details
|
|
|
|
10-02-2011
|
4.00
|
Right elevator assembly
|
Details
|
|
|
|
10-01-2011
|
3.00
|
Right elevator
|
Details
|
|
|
|
08-23-2011
|
1.50
|
|
Details
|
|
|
|
08-15-2011
|
3.00
|
E 703, 704, 713 assembly
|
Details
|
|
|
|
05-29-2011
|
4.00
|
Bending the trailing edge of the elevators
|
Details
|
|
|
|
05-23-2011
|
5.50
|
Left Hand Stiffeners
|
Details
|
|
|
05-02-2011
|
3.50
|
Remaining stiffeners right side
|
Details
|
|
|
|
05-01-2011
|
4.00
|
Bending the trailing edge of elevator
|
Details
|
|
|
|
04-18-2011
|
6.00
|
Elevator Stiffener creation and placement
|
Details
|
|
|
04-09-2011
|
3.00
|
Forming stiffeners
|
Details
|
|
|
|
03-27-2011
|
5.00
|
Riveting trailing edge of rudder
|
Details
|
|
|
|
03-26-2011
|
3.00
|
01 skin to counterweight skin and rib
|
Details
|
|
|
|
03-21-2011
|
1.50
|
counterweight and rib install
|
Details
|
|
|
|
03-12-2011
|
3.00
|
Rudder trailing edge couterbalance
|
Details
|
|
|
03-10-2011
|
1.00
|
rivetted counterweight skin to rudder spar
|
Details
|
|
|
|
03-06-2011
|
2.50
|
Rudder counterbalance
|
Details
|
|
|
|
02-16-2011
|
1.50
|
Drill and Dimple R901 skins for riveting
|
Details
|
|
|
|
02-06-2011
|
3.00
|
Rudder horn, attach strips
|
|
|
|
02-06-2011
|
1.50
|
Dimpling skins
|
Details
|
|
|
|
02-03-2011
|
1.50
|
Gluing Rudder trailing edge
|
Details
|
|
|
01-29-2011
|
2.00
|
finish drill clecoed R901 skins to ribs and trail
|
Details
|
|
|
11-21-2010
|
2.00
|
Radused and fit rudder horn to R - 904
|
Details
|
|
|
11-15-2010
|
1.50
|
left rudder skin stiffener riveting
|
Details
|
|
|
11-10-2010
|
2.00
|
match drill stiffeners to left rudder skin
|
Details
|
|
|
|
10-30-2010
|
4.50
|
Installing stiffeners to the Rudder right hand sid
|
Details
|
|
|
|
10-24-2010
|
1.50
|
Rudder Stiffeners
|
Details
|
|
|
|
09-13-2010
|
1.30
|
Riveting left side fin
|
Details
|
|
|
|
09-12-2010
|
1.50
|
Riveting the skin to the Fin Skeleton
|
|
|
|
09-11-2010
|
3.00
|
Building Fin Skeleton
|
|
|
|
09-01-2010
|
1.00
|
Riveting the 808pp to the stiffener, with AN426
|
|
|
|
08-31-2010
|
2.50
|
Dimpling 808 and countersink stiffener
|
Details
|
|
|
|
08-25-2010
|
2.00
|
familiarizing with rivets
|
Details
|
|
|
|
05-16-2010
|
3.00
|
primer of empennage
|
|
|
|
05-15-2010
|
2.00
|
Prep empennage
|
Details
|
|
|
03-15-2010
|
1.50
|
Prep and primer study
|
Details
|
|
|
|
03-09-2010
|
2.00
|
Dimpling fin structure
|
Details
|
|
|
02-21-2010
|
2.00
|
Dimpling the fin
|
Details
|
|
|
02-18-2010
|
0.50
|
Drilling the Starboard side fin
|
Details
|
|
|
|
02-17-2010
|
1.00
|
match drilling of empennage
|
Details
|
|
|
|
01-23-2010
|
3.00
|
assemble ribs to vertical spar
|
Details
|
|
|
01-12-2010
|
2.00
|
Vertical Stabiliser
|
Details
|
|
|
|
01-04-2010
|
0.50
|
review and installation of Kitlog Software
|
|
|
