Powered By Kitlog Pro v2.0
BOB'S WEB SITE
RV-12iS
Empennage
Work Logs Found:
57
Category Work Time:
111 Hours
Date
Hours
Work Log Summary
Details
10-31-2020
0.20
Fully finished SD-00001 service bulletin
Details
10-27-2020
1.50
Mostly finished with SD-00001
Details
10-26-2020
1.50
Began replacing trim motor
Details
10-07-2019
1.00
Finished most of service bulletin
Details
10-06-2019
1.50
Riveted gussets
Details
10-04-2019
2.00
Assembled new hinge brackets
Details
10-01-2019
2.00
Started on spar service bulletin
Details
03-28-2017
2.00
Completed empennage kit
Details
03-27-2017
2.00
Wired connector for trim servo
Details
03-26-2017
2.00
Assembled trim pushrods etc.
Details
03-25-2017
3.00
Fit control surfaces to tailcone
Details
03-24-2017
0.50
Fit vertical stabilizer
Details
03-21-2017
1.50
Completed tailcone
Details
03-19-2017
3.00
Began riveting top skin
Details
03-18-2017
1.25
Fit the top tailcone skin
Details
03-17-2017
1.50
Completed side skin riveting on tailcone
Details
03-16-2017
1.00
Completed right side of side skin riveting
Details
03-15-2017
0.75
More riveting of side skins
Details
03-14-2017
1.00
Riveting side skins
Details
03-12-2017
2.50
Installed some system runs
Details
03-11-2017
3.00
Completed riveting tail cone bottom
Details
03-10-2017
1.50
More riveting of bottom skins
Details
03-09-2017
3.00
Riveted bottom skin halfs
Details
03-02-2017
1.00
Fit side skirts to tailcone
Details
02-26-2017
1.00
Started work tail cone skin
Details
02-25-2017
2.00
Fit aft bulkhead to stabilator
Details
02-24-2017
1.00
Finished riveting aft bulkhead
Details
02-23-2017
1.50
Riveting aft bulkhead
Details
02-22-2017
0.50
Made tie-down bracket
Details
02-20-2017
5.00
Assembled bulkheads
Details
02-19-2017
1.50
Completed stabilator
Details
02-18-2017
6.00
Finished riveting the stabilator
Details
02-17-2017
1.50
Began riveting left skin on stabilator
Details
02-16-2017
1.00
Completed right stabilator skin
Details
02-15-2017
1.00
More riveting
Details
02-14-2017
1.50
Reamed holes
Details
02-12-2017
1.00
Fit skin on stabilator
Details
02-11-2017
7.00
Completed stabilator spar assembly
Details
02-10-2017
2.00
Riveted control brackets
Details
02-09-2017
2.00
Riveted nutplates
Details
02-08-2017
2.00
Spar box assembly
Details
02-06-2017
0.50
Stabilator spar box assembly
Details
02-05-2017
2.00
Stabilator parts prep
Details
02-05-2017
1.00
More priming
Details
02-05-2017
1.00
More part prep for stabilator
Details
02-04-2017
2.00
Completed right anti servo tab assembly
Details
02-03-2017
1.00
Started work on right trim assembly
Details
02-02-2017
1.00
Completed left trim assembly
Details
01-27-2017
3.00
Primed and riveted rudder parts
Details
01-27-2017
4.00
Completed rudder
Details
01-23-2017
3.00
Began work on rudder
Details
01-22-2017
5.00
Completed vertical stabilizer
Details
01-21-2017
4.00
Completed VS rib/spar assembly
Details
01-20-2017
1.00
Riveted upper spar caps to rear VSspar
01-17-2017
1.00
Completed other half of VS spar doubler
01-16-2017
2.00
First parts for vertical stabilizer
01-14-2017
2.00
Kit arrival and inventory
Details
SITE NAVIGATION
Contact Builder
RV-12iS Home
Category
# Logs
# Hours
All
400
797
Electrical
6
12
Empennage
57
111
Engine
38
78
Finishing Kit
97
183
Fuselage
131
255
Hardware
1
2
Miscellaneous
3
6
Prop
16
20
Tools
1
2
Wings
50
128
Copyright © 2001-2024 Matronics. All Rights Reserved.
