Powered By Kitlog Pro v2.0
Bruces S-19 Build Log
S-19 Venterra
Wings
67 Logs Found
Date
Hours
Work Log Summary
Details
02-07-2013
10.0
Assembled frame, started electrical installation
Details
02-02-2013
8.0
Primed wing details
Details
12-20-2012
5.0
Finished up the tip
Details
12-17-2012
10.0
Built the RHS wing tip
Details
12-12-2012
10.0
Finished drilling wing skins
Details
12-01-2012
20.0
Started skining wing
Details
11-26-2012
5.0
Assembled Wing frame
Details
11-24-2012
8.0
Primed wing components
Details
11-19-2012
10.0
Prepared wing for primer
Details
07-23-2012
10.0
Building up the frame
Details
07-18-2012
10.0
Started the Right Hand Wing
Details
04-27-2012
2.0
Hung wing in rafters for safe keeping
Details
04-10-2012
6.0
Finished the Left Hand Wing!
Details
04-08-2012
6.0
Turned wing upright and clecoed upper skin
Details
04-07-2012
8.0
Riveted Lower Wing Skin
Details
04-01-2012
4.0
Installed Lower Aft wing skin
Details
03-31-2012
6.0
Installed Fuel Tank
Details
03-28-2012
4.0
Fixed leaky fuel cap
Details
03-25-2012
8.0
Pressure tested tank - home made manometer.
Details
03-21-2012
3.0
Installing fuel sender
Details
03-21-2012
2.0
Finisher sender installation
Details
03-03-2012
8.0
Fuel tank prep
Details
02-26-2012
2.0
Finished fuel lines
Details
02-26-2012
8.0
Fabricated fuel return lines
Details
01-29-2012
2.0
Fuel tank prep
Details
01-15-2012
4.0
Fuel tank hadware
Details
01-14-2012
4.0
Drilled the fuel pick-up tubes.
Details
12-24-2011
4.0
Modified sender ring, drilled mounting holes in ta
Details
12-23-2011
2.0
Trimed fuel tank filler necks
Details
12-14-2011
6.0
Planing for a wing tip VOR/ILS antenna
Details
11-30-2011
16.0
Primed Skins and Leading Edge
Details
10-31-2011
6.0
Built a handling table
Details
10-23-2011
6.0
Started with fuel tank
Details
10-22-2011
8.0
Building the aileron push rods
Details
10-09-2011
8.0
Finished drilling left hand wing
Details
10-04-2011
2.0
How not to drill a hole (or impress your wife)
Details
10-02-2011
6.0
Formed LE skins
Details
10-01-2011
1.0
Turned wing top side up
Details
10-01-2011
2.0
Finished the bottom of the wing.
Details
10-01-2011
6.0
Fabricated Torque Angle
Details
09-24-2011
4.0
Drilled Lower Leading Edge Skin
Details
09-09-2011
2.0
Loaded LE wing skin
Details
09-07-2011
2.0
Trimed fwd LE ribs
Details
09-05-2011
2.0
Modified and match drilled aileron hinge doublers
Details
08-29-2011
3.0
Set Flap hinge
Details
08-28-2011
6.0
Aligned Aileron Hinge
Details
07-04-2011
2.0
Reset wing top side up
Details
07-03-2011
1.0
One man wing flip
Details
07-03-2011
8.0
Drilling wing skins
Details
07-02-2011
4.0
Drilling wing skins
Details
07-01-2011
4.0
Started drilling wing skins
Details
06-28-2011
1.0
Fabricated wing skin stiffeners
Details
06-26-2011
2.0
working on the wing skins
Details
06-25-2011
6.0
Set up work bench blocks and trued wing
Details
06-20-2011
16.0
primed and riveted the LHS wing frame
Details
06-18-2011
12.0
primed the LHS wing frame
Details
06-11-2011
4.0
Details
06-04-2011
6.0
Deburing wing details
Details
05-30-2011
4.0
Drilling out the rear spar
Details
05-26-2011
3.0
Nose rib assy
05-21-2011
8.0
Touch up work on the machined spars
Details
05-21-2011
4.0
Continuing on the left hand wing assy
Details
01-12-2011
8.0
Perliminary assy of the wing
Details
01-09-2011
8.0
Unpacked wing crate and started LH wing
Details
05-30-2010
4.0
Reamed Wing Spars
Details
05-16-2010
6.0
Inventoried wing kit
Details
04-08-2010
4.0
Wing Kit Arived
Details
SITE NAVIGATION
Contact Builder
S-19 Venterra Home
All
Aft Fuselage
Aileron
Builder
Center Fuselage
Controls
Demo Flight
Distractions
Electrical
Empennage
Flaps
Forward Fuselage
Fuselage
Horiz Stabilator
Instruments
Landing Gear
Project
Rudder
Seats
Shop
Tips
Tools
Trim Tab
Vertical Stablizer
Wings
Copyright © 2001-2013 Matronics. All Rights Reserved.
