Powered By Kitlog Pro v2.0
Mark Weitkamp CX4
CX4
Fuselage
Work Logs Found:
57
Category Work Time:
390 Hours
Date
Hours
Work Log Summary
Details
05-30-2020
9.00
front spar of vertical fin fitted to fuselage
Details
05-28-2020
7.00
side skins by tail wheel
Details
05-27-2020
8.00
side skins above tailwheel
Details
05-21-2020
8.00
drilled and clecoed new F10 bulkhead
Details
05-19-2020
4.00
debur left side fuse skin and trim to final size
Details
05-18-2020
5.00
fabricate tail spring pivot
Details
05-17-2020
7.00
made form block for F10 and formed F10
Details
05-16-2020
7.00
up drilled left side skin rivet holes plus new F10
Details
05-14-2020
6.00
trimming fuselage skin and longerons
Details
05-12-2020
6.00
work on fuselage skin and bulkheads
Details
05-11-2020
4.00
planning F 11 and F 12 installation
Details
03-13-2020
10.00
finish fitting aft left side fuselage skins
Details
03-12-2020
10.00
left side aft skin on fuselage
Details
03-10-2020
10.00
right side aft fuselage skins
Details
03-09-2020
6.00
continue fuselage skin fitting
Details
03-08-2020
8.00
continuing to fit aft fuselage skins
Details
03-04-2020
10.00
deburred and rivetted top skin of aft fuselage
Details
03-01-2020
10.00
deburred and riveted bottom skin
Details
02-29-2020
10.00
rebuild bulkhead F 9
Details
02-23-2020
5.00
continuing fitting skin of aft fuselage
Details
02-12-2020
8.00
bottom skin forming
Details
02-11-2020
10.00
finished fitting top skin, cut out bottom skin
Details
02-10-2020
8.00
continue forming top skin to bulkheads
Details
02-09-2020
8.00
top skin of aft fuselage
Details
02-08-2020
8.00
set up aft bulkheads
Details
02-02-2020
8.00
forward fuselage to end of table, controls work
Details
01-29-2020
6.00
Drilled and rivetted F3 to vertical angle
Details
01-27-2020
8.00
torqued gusset bolts, installed F3 bulkhead
Details
01-25-2020
7.00
seat back rivetting, gusset bolting, machine screw
Details
01-17-2020
9.00
completed installation of F5 bulkheads
Details
01-16-2020
4.00
checking and fine-tuning alignment and levelling
Details
12-24-2019
8.00
bolt upper longerons to firewall, install angle at
Details
12-21-2019
6.00
attachment and bracing of forward longerons
Details
12-18-2019
6.00
fabricate upper forward longerons
Details
12-17-2019
9.00
lower longerons attached
Details
12-14-2019
8.00
stiffened firewall, fabricated lower longerons
Details
12-09-2019
4.00
welding on control stick
Details
12-08-2019
4.00
beginning bulkhead setup
Details
12-02-2019
4.00
cleared assembly table and set up tailcone jig
Details
11-30-2019
4.00
formed firewall, pulled wings off
Details
11-29-2019
4.00
Bulkheads F3 and F4
Details
11-27-2019
5.00
Final rivet F9, form F11 and F12
Details
11-25-2019
6.00
forming and assembly of bulkhead F9
Details
11-22-2019
8.00
cut out aluminum blanks for bulkhead components
Details
11-21-2019
6.00
fabricate bulkhead F10
Details
11-18-2019
8.00
Fuselage bulkheads f2 and f8
Details
11-10-2019
6.00
bulkhead F2 and control stick
Details
11-08-2019
8.00
forming and fabricating bulkhead F6
Details
11-06-2019
6.00
formed forward floor supports and cut out aluminum
Details
11-03-2019
8.00
final test of fitting wings to center section befo
Details
09-11-2019
5.00
bottom skin of center section riveted on
Details
09-09-2019
6.00
center section bottom skin
Details
09-08-2019
6.00
seat pan finally riveted
Details
09-07-2019
6.00
substructure under seat pan
Details
09-06-2019
7.00
continued test fitting and refinement of seat ribs
Details
08-13-2019
4.00
cut out the firewall
Details
04-16-2011
4.00
cutting out aluminum for fuselage and fin
Details
SITE NAVIGATION
Contact Builder
CX4 Home
Category
# Logs
# Hours
All
504
2592
Control system
24
133
cylinder baffling, p
26
93
Empennage
44
216
Engine
41
223
engine cowling
86
365
fixtures and forms
17
86
Fuel System
3
13
Fuselage
57
390
Landing Gear
7
54
Miscellaneous
20
81
paperwork for regist
1
100
Time spent on projec
4
24
Wings
174
814
Copyright © 2001-2024 Matronics. All Rights Reserved.
