KitLog pro

Powered By Kitlog Pro v2.0

BRAD'S WEB SITE
Work Logs Found: 92
Category Work Time: 495 Hours
 Date
Hours
Work Log Summary

Details

 04-10-2018
4.50
Drilled rear of lower engine cowling
Details

 04-08-2018
5.00
Engine cowling
Details

 04-07-2018
8.00
Cowling
Details

 04-06-2018
8.00
Hung Engine and prop!
Details

 04-05-2018
7.00
Re-drilled flap arms
Details
     

 04-04-2018
3.00
Ran gas through right wing
Details

 04-03-2018
3.00
Trimmed windshield
Details
     

 04-02-2018
8.00
Aileron travel & fuel lines
Details

 03-31-2018
9.00
Wing cables and fuel lines.
Details
       

 03-30-2018
4.00
Fuel site guage
Details

 03-29-2018
2.00
Fuel line coonections
Details

 03-28-2018
10.00
Flap & Aileron cables, fuel lines
Details
       

 03-27-2018
6.00
Aileron cables, wing fuel line connections
Details
     

 03-26-2018
5.00
Drilled flap arms and Flap cables
Details
     

 03-25-2018
5.00
C Channel for nosebowl support
Details
     

 03-24-2018
4.00
Brake lines
Details
       

 03-23-2018
4.00
Hung Wings
Details
     

 03-15-2018
6.00
Engine mount and Tail wires
Details
       

 03-13-2018
5.00
Putting the tail together
Details
       

 03-12-2018
5.00
Fuselag is back on wheels
Details

 03-10-2018
4.00
Fuselage main plumbing
Details
       

 03-09-2018
3.00
Planning wing closure for site guages
Details
       

 03-09-2018
5.00
Mounting the gascolator
Details
       

 03-09-2018
5.00
Brake lines and gascolator
Details
       

 03-08-2018
3.00
Wing wiring and wing cable fairleads
Details
       

 03-07-2018
3.00
The wing is finished!!
Details
       

 03-07-2018
5.00
Back to wing # 1
Details
       

 03-06-2018
8.00
Finished the plumbing on 2nd wing
Details
       

 03-06-2018
3.00
Finished the plumbing and mounted the wingtip
Details
       

 03-05-2018
8.00
Mounted the aux fuel pump
Details
       

 02-27-2018
4.00
Started on 2nd wing plumbing
Details
       

 02-26-2018
5.00
Fuel caps and fuel lines
Details
       

 02-25-2018
0.00
Pausing to work on the airboat
Details
       

 02-25-2018
4.00
Opening up the finished wing
Details
       

 02-19-2018
4.00
Pulled the tanks again and cleaned up!
Details

 02-18-2018
4.00
Did a fuel transfer leak check
Details

 02-17-2018
3.00
Fairleads and stiffeners
Details
       

 02-16-2018
1.00
Easy day. Worked on a fairlead and went flying
Details
       

 02-15-2018
5.00
More gas line stuff
Details
       

 02-14-2018
5.00
Tapped bad threads, fabricated tank lines
Details
       

 02-13-2018
5.00
drilled / dimpled fuel hole cover, worked gas line
Details
       

 02-12-2018
4.00
Drilled control arm brackets, cut stiffener
Details
       

 02-11-2018
1.50
Wing root ribs
Details
       

 02-11-2018
7.50
Flap / aileron hinges and install
Details
       

 02-10-2018
1.50
Trying to understand flap/aileron attachment
Details
       

 02-10-2018
9.00
Finished all access panels
Details
       

 02-09-2018
5.00
Main and Aux tank bay covers
Details
       

 02-08-2018
8.00
Access panels
Details
       

 02-07-2018
8.00
First flush rivets! Started access panels
Details
       

 02-06-2018
5.00
Fuel pump plate and opened up control path
Details
       

 02-05-2018
5.00
Cut fuel cap opening in wing and installed vent li
Details
       

 02-04-2018
4.00
Installed main tank, worked out strap placement
Details

 02-03-2018
5.00
Experimented with Rivets, started fuel lines
Details

 02-02-2018
7.00
Worked on bell crank / flaps
Details
       

 02-01-2018
10.00
Wire brushed and painted straps
Details
       

 01-31-2018
12.00
Cut out aux tank spot in wing and straps
Details
       

 01-30-2018
7.00
Finished Main tank straps and worked aux tank
Details
       

 01-29-2018
12.00
Wing controls fuel tank straps
Details
       

 01-28-2018
8.00
Cleaned out the wings, re-welded 2nd float fitting
Details
       

 01-27-2018
6.00
First day looking at a wing!
Details
       

 01-24-2018
8.00
Grinded and grinded and welded float fittings
Details
       

 01-23-2018
4.00
Formulated a plan to fit the float fittings
Details
       

 01-22-2018
3.00
Ordered shoulder harness and research
Details

 01-21-2018
7.00
Second gear leg complete and fitted rear seat
Details
       

 01-20-2018
6.00
Landing gear and a few more tabs
Details
       

 01-18-2018
5.00
Finished skylight, added gopro tabs and gussets
Details
       

 01-17-2018
8.00
Finished tabs and half of skylight
Details
       

 01-16-2018
11.00
Welded tabs
Details
       

 01-15-2018
9.50
Cut tabs and test fit sky light
Details
       

 12-08-2017
1.00
Lexan test fit for kinks and dimples
Details
       

 12-08-2017
8.50
Adding skylight tubing support
Details
       

 12-07-2017
4.50
Working Rotisserie and first weld
Details
       

 12-04-2017
1.00
The expensive lesson
Details
     

 12-04-2017
8.00
Finished rotisserie front and rear connections
Details
       

 12-02-2017
4.50
Gettin Tiggy with it
Details
       

 12-01-2017
4.50
Brennan finished his mouse door
Details
       

 11-29-2017
6.00
Finished welding rotisserie pieces
Details
     

 11-27-2017
4.50
Welded 2 rotiserie bases for wings and fuselage
Details
       

 11-23-2017
4.50
Fabricating tubing support for sky light
Details
       

 11-21-2017
6.00
Brennan's Door is hung and rear window cut
Details
       

 11-20-2017
3.00
Mouse door and cut roof stringers for sky light
Details
       

 11-16-2017
8.00
Doors almost all formed
Details
       

 11-14-2017
6.00
More door work
Details
       

 11-13-2017
6.50
Installed Lexan in Pilot window
Details
     

 11-12-2017
1.00
Brennan worked on his door
Details
     

 11-09-2017
8.00
More door work
Details
       

 11-07-2017
2.00
Started on Doors
Details
       

 11-06-2017
5.00
Drilled and tapped 2 bushings for rear seat
Details

 11-05-2017
5.00
Planning window layout
Details
       

 11-03-2017
3.00
Saw my first Bearhawk!
Details
     

 11-01-2017
4.00
Test fit the tail feathers, floor, seats, control
Details
       

 10-29-2017
5.00
Step 1: Begin the organization
Details
       










Copyright © 2001-2024 Matronics. All Rights Reserved.