Date
|
Hours
|
Work Log Summary
|
Details
|
01-11-2014
|
1.75
|
Installing wing root fairings
|
Details
|
|
|
09-30-2013
|
0.75
|
Safety wired the flaps
|
Details
|
|
|
04-16-2013
|
2.25
|
Trimming the wing root fairing and installing seal
|
Details
|
|
|
02-11-2012
|
0.00
|
Adjusting the flap pushrods.
|
Details
|
|
|
01-28-2012
|
1.75
|
Adjusting the flap and fuselage gap
|
Details
|
|
|
05-30-2011
|
2.75
|
Riveted wingtip rib & safety wired the
|
Details
|
|
|
03-21-2011
|
3.50
|
Installing the wings for the last time.
|
Details
|
|
|
12-29-2010
|
5.50
|
Installing wing root nut plates.
|
Details
|
|
|
05-09-2009
|
4.25
|
Installation of the wing flap pushrods
|
Details
|
|
|
03-02-2009
|
4.00
|
Right wing outboard lower skin
|
Details
|
|
|
02-02-2009
|
4.00
|
Rivet lower outboard wing skin.
|
Details
|
|
|
01-26-2009
|
4.00
|
Primed wing skins and installed fuel sender.
|
Details
|
|
|
01-19-2009
|
6.00
|
Dimpled wing skins, installed wing tips and nutpla
|
Details
|
|
|
01-04-2009
|
3.00
|
Debured and dimpled the wing skin
|
Details
|
|
|
01-03-2009
|
7.00
|
Wing tip installation
|
Details
|
|
|
11-01-2004
|
2.00
|
Enlarge exisiting wire run holes
|
Details
|
|
|
11-02-2003
|
6.00
|
Wing root nut plates and F-796B support brackets.
|
Details
|
|
|
10-28-2003
|
0.00
|
Landing light installation.
|
Details
|
|
|
10-26-2003
|
1.50
|
Wing Root Fairing Installation.
|
Details
|
|
|
10-25-2003
|
0.75
|
Fuel tank attach brackets.
|
Details
|
|
|
10-25-2003
|
2.00
|
Drilling the rear spar
|
Details
|
|
|
10-24-2003
|
1.50
|
Setting the angle of incidence.
|
Details
|
|
|
10-23-2003
|
4.00
|
Wing mating
|
Details
|
|
|
10-23-2003
|
0.50
|
Securing the pushrods and ailerons.
|
Details
|
|
|
10-21-2003
|
0.75
|
Preparing the rear spar-02
|
Details
|
|
|
10-21-2003
|
2.50
|
Preparing the rear spar-01
|
Details
|
|
|
09-25-2003
|
1.25
|
Pitot tube hole and attachment.
|
Details
|
|
|
09-23-2003
|
1.00
|
Pitot tube hole.
|
Details
|
|
|
07-04-2003
|
0.00
|
Outboard skin cleo'd and ready for drilling.
|
Details
|
|
|
07-03-2003
|
12.00
|
Countersinking flap hinges and drilled holes in ai
|
Details
|
|
|
06-25-2003
|
7.00
|
Drilling the flap hinges
|
Details
|
|
|
06-23-2003
|
0.00
|
Aileron installation
|
Details
|
|
|
06-22-2003
|
0.00
|
Aileron installation
|
Details
|
|
|
06-21-2003
|
4.00
|
Aileron installation
|
Details
|
|
|
06-20-2003
|
7.00
|
Gap fairing, flap brace, and W-716 contol tube.
|
Details
|
|
|
06-14-2003
|
3.00
|
Aileron control rods
|
Details
|
|
|
06-09-2003
|
3.00
|
Aileron attach brackets.
|
Details
|
|
|
06-08-2003
|
4.00
|
Attach brackets, gap fairings, and braces.
|
Details
|
|
|
06-07-2003
|
2.00
|
Drilling the flap braces and aileron gap fairings.
|
Details
|
|
|
06-07-2003
|
0.00
|
Aileron Brackets-02
|
Details
|
|
|
06-06-2003
|
2.50
|
Aileron Brackets-01
|
Details
|
|
|
06-03-2003
|
2.75
|
Large Aileron Pushrods.
|
Details
|
|
|
06-01-2003
|
1.75
|
Aileron control tubes
|
Details
|
|
|
05-31-2003
|
2.00
|
Install bell cranks
|
Details
|
|
|
05-29-2003
|
2.00
|
Bell crank work
|
Details
|
|
|
04-27-2003
|
2.00
|
Wing cradle work
|
Details
|
|
|
04-18-2003
|
6.00
|
Started building the wing cradle.
|
Details
|
|
